D-Link DWA-F18 VR Air Bridge User guide

Type
User guide

This manual is also suitable for

D-Link DWA-F18 VR Air Bridge is a device that allows you to connect your VR headset to your computer wirelessly. It uses a USB 3 port on your computer and connects to your VR headset via Wi-Fi. The VR Air Bridge is designed to provide a high-quality, low-latency connection for VR gaming and other applications. It also features a companion stand to keep the VR Air Bridge vertical and ensure a clear line of sight between the device and your VR headset.

D-Link DWA-F18 VR Air Bridge is a device that allows you to connect your VR headset to your computer wirelessly. It uses a USB 3 port on your computer and connects to your VR headset via Wi-Fi. The VR Air Bridge is designed to provide a high-quality, low-latency connection for VR gaming and other applications. It also features a companion stand to keep the VR Air Bridge vertical and ensure a clear line of sight between the device and your VR headset.

Ver 1.00(FB)_90x130 2021/11/08 5300-00008187-01X
Set-up
1 /
Drivers
Download
oculus.com/setup II
Use these tips to get the best performance
In the same room as the VR headset
Line of sight (unobstructed view between
VR Air Bridge and VR headset)
Desk height
Keep the VR Air Bridge vertical using the
companion stand
Best placement for VR Air Bridge
Support
For more information about PC compatibility
requirements with Quest headsets, please visit
support.oculus.com
For additional support, go to:
https://support.dlink.com
Quick Start Guide
x1 x1 x 1
DWA-F18
VR Air Bridge
Powered by Quest Link Software
Contents in the box
Go to oculus.com/setup to download and
install the Quest Link Software. For those
who have the software already, ensure you
are running the most recent version, if not,
update and reboot your computer.
2 /
Connect the VR Air Bridge to a USB 3
port on your computer (they are blue).
Open the Quest Link Software and check
that VR Air Bridge is detected
FCC INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution
This device and its antenna must not be co-located or operating in conjunction with
any other antenna or transmitter. This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference
that may cause undesired operation. Any changes or modifications not
expressly approved by the party responsible for compliance could void the
authority to operate equipment.
This device is restricted to indoor use.
Federal Communication Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20 cm between the radiator and your body. This device
complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference
that may cause undesired operation.
For products available in the USA/Canada market, only channel 1~11 can be
operated. Selection of other channels is not possible.
  • Page 1 1

D-Link DWA-F18 VR Air Bridge User guide

Type
User guide
This manual is also suitable for

D-Link DWA-F18 VR Air Bridge is a device that allows you to connect your VR headset to your computer wirelessly. It uses a USB 3 port on your computer and connects to your VR headset via Wi-Fi. The VR Air Bridge is designed to provide a high-quality, low-latency connection for VR gaming and other applications. It also features a companion stand to keep the VR Air Bridge vertical and ensure a clear line of sight between the device and your VR headset.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI