Rain Harvesting Clean Rain Ultra Installation guide

Brand
Rain Harvesting
Model
Clean Rain Ultra
Category
Sanitary ware
Type
Installation guide

Rain Harvesting Clean Rain Ultra is an all-in-one rainwater diverter that ensures clean water is diverted to your tank, barrel, pool, or garden. It features a rain head and first flush diverter, integrated cover and cap, and a vibrating screen and leaf slide for easy cleaning. The Clean Rain Ultra can be used with a garden hose, greywater hose, pool hose, or 90mm pipe, and has an internal mosquito barrier to prevent pests from entering. It is easy to install and maintain, and complies with various Australian and New Zealand standards.

Rain Harvesting Clean Rain Ultra is an all-in-one rainwater diverter that ensures clean water is diverted to your tank, barrel, pool, or garden. It features a rain head and first flush diverter, integrated cover and cap, and a vibrating screen and leaf slide for easy cleaning. The Clean Rain Ultra can be used with a garden hose, greywater hose, pool hose, or 90mm pipe, and has an internal mosquito barrier to prevent pests from entering. It is easy to install and maintain, and complies with various Australian and New Zealand standards.

Code
Size
Country
DDCR01
90mm
100mm
100x50mm
100x75mm
Australia
DDCR99
3" SCH40
4" SCH40
2x3"
3x4"
USA
Clean Rain Ultra
PRODUCT DETAILS
An all-in-one rainwater diverter which incorporates a
rain head and first flush diverter to ensure clean
water is diverted to your rainwater tank, rain barrel,
pool or garden. The integrated cover and cap
provide a stylish finish.
Installation and Specification Guide
rainharvesting.com
WHAT'S IN THE BOX? TOOLS/MATERIALS YOU MAY REQUIRE
INSTALLATION
Clean Rain Ultra Tape measure
Marker pen
Saw
Screws
Screwdriver or drill
Solvent cement glue
Installation
1 - Remove 745mm of downpipe from where the Clean Rain® is to be situated. Ensure all edges are clean
and smooth.
2 - Remove the cap and use snips to remove a section to fit the downpipe.
3 - Remove the cover by flexing outwards at the top.
4 - Fit the correct downpipe adaptor to the bottom of the Clean Rain®.
5 - Slide the cap up the top section of downpipe and hold temporarily in place.
6 - Install the Clean Rain® by positioning it securely on the bottom section of downpipe.
7 - Screw the top of the Clean Rain® in position through the screw slots provided. Ensure appropriate
screws and anchors (if required) are used.
8 - Check the placement of the Vibrating Screen. It must sit behind and below the front face (FIGURE 1).
9 - Insert the Leaf Slide into slot holes (FIGURE 2).
10 - Re-install the front cover.
11 - Slide the cap back down the downpipe until it sits securely on top of the Clean Rain® unit.
12 - Fit the hose or pipe of your choice (20mm garden hose thread, 22mm greywater hose, 38mm pool
hose or 90mm pipe) to the outlet.
(a) For a garden hose, unscrew one or two caps and screw one or two garden hoses onto the outlet.
(b) For a 22mm greywater hose and 38mm pool hose, unscrew the cap and push the hose onto the outlet.
(c) For 90mm pipe, remove the outlet cap and cut off the hose fittings, then insert the cap into 90mm
pipe and glue. Reinsert the cap into the Clean Rain outlet and swivel the Clean Rain body to direct the
pipe towards your rainwater tank or where the rainwater is being diverted to.
rainharvesting.com
Figure 1
Suggested Installation Orientations
Figure 2
Suggested Installation Orientations
NOTE: ON/OFF Switch - The Clean Rain® can be turned off so that no water is diverted to your rainwater
tank, rain barrel, pool or garden. To do this simply flick the switch on the front of the Clean Rain® and in
the next rainfall event all the water will be diverted to stormwater.
rainharvesting.com
Country
Code
A
B
C
D
E
G
Australia
DDCR01
90 M
90 F
796
206
513
20mm garden
hose thread
22mm greywater hose
38mm pool hose
Fits into 90mm Pipe
(cut off end of outlet)
100 F
100 F
100x50 M
100x50 F
100x75 M
100x75 F
USA
DDCR99
3"SCH40 M
3"SCH40 F
31.34"
8.11"
20.20"
4" SCH40 M
4" SCH40 F
2"x3" M
2"x3" F
3"x4" M
3"x4" F
Product Specifications
Clean Rain Ultra
rainharvesting.com
All dimensions are in mm unless otherwise stated.
Fitting guide:
F = Female / Socket Fitting (Pipe fits inside)
M = Male / Spigot Gitting (Pipe size, fits into a socket)
LEFT SIDE VIEW FRONT VIEW RIGHT SIDE VIEW
A common misconception about collecting rainwater is that all you need is a
roof, a tank and some rain. This ‘tanking’ approach cannot always be relied on to
deliver the volume – or quality – of water that you require. That is where we can
help.
With some thought, your rain harvesting system can provide you with cleaner
water and lots of it. Whether you’re completely reliant on tank water or wanting
to keep the garden green, our simple steps will help you achieve your goal.
The Rain Harvesting approach to rainwater collection involves using tested and
proven products to make quality rainwater available for use in and around your
property. You don’t need much to get started and you will be surprised how
easy it is to get the most out of your rainwater system.
How can we help you?
DISCLAIMER This product specification is not a complete guide to product usage. Further information is available from Rain Harvesting Pty Ltd and from the installation and Operating
instructions. This specification sheet must be read in conjunction with the installation and Operating Instructions and all applicable statutory requirement. Product specifications may
change without notice. © Rain Harvesting Pty Ltd
rainharvesting.com
Maintenance
COMPLIANCE
The Clean Rain® is mostly self-cleaning, however it may require occasional maintenance in order to keep it
functioning optimally.
– The leaf slide and vibrating screen can both be removed when the cap and cover are off by lifting
up and out. If cleaning is required simply hose or brush off any debris.
Replace as per figure 1 and 2.
– The outlet has an internal mosquito barrier that prevents any mosquitoes from entering the system.
To clean simply remove the outlet by holding the unit in one hand and with a firm pull remove the outlet
adaptor.
– The Smart Sense® valve may require the occasional clean to remove any build-up of sediment.
To clean remove the Clean Rain® from the wall and take the bottom adaptor off the unit. The hygroscopic
washers within the Clean Rain have a long service life and should not require replacement. However, should
you notice decreased amounts of first flush or increasingly longer re-set periods then your washers may
require replacement. Please contact Rain Harvesting for a full replacement set.
RAIN HEAD
OUTLET
FIRST FLUSH
AS/NZS 3500.3:2003 Plumbing and Drainage
HB230:2008 Rainwater Tank Design and
– Stormwater Drainage
Installation Handbook
enHealth Council
Queensland Health Regulations 1996
– Guidance on the Use of Rainwater Tanks
– Preventing Mosquitoes Breeding
(Part 8 – Mosquito Prevention)
For more information or to find out
how we can help, just give us a call on
+61 7 3248 9600
Or visit our website at
rainharvesting.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Rain Harvesting Clean Rain Ultra Installation guide

Brand
Rain Harvesting
Model
Clean Rain Ultra
Category
Sanitary ware
Type
Installation guide

Rain Harvesting Clean Rain Ultra is an all-in-one rainwater diverter that ensures clean water is diverted to your tank, barrel, pool, or garden. It features a rain head and first flush diverter, integrated cover and cap, and a vibrating screen and leaf slide for easy cleaning. The Clean Rain Ultra can be used with a garden hose, greywater hose, pool hose, or 90mm pipe, and has an internal mosquito barrier to prevent pests from entering. It is easy to install and maintain, and complies with various Australian and New Zealand standards.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents