T-Fal 1700 Serie Owner's manual

Category
Irons
Type
Owner's manual

This manual is also suitable for

maxmax
032503 - 21/03
Mod. : 1500 series
1700 series
Use and care instructions / Instrucciones de uso y mantenimiento / Notice d’emploi
A. Spray Button
To moisten fabrics
B. Burst of Steam Button
(depending on model)
To remove wrinkles
C. Auto Shut off indicator light
(depending on model)
D. Electric power cord
E. Thermostat indicator light
Goes out when the correct
temperature has been reached.
F. Thermostat control
For choosing the ironing temperature
G. Water reservoir maximum fill line
Do not exceed this limit
H. Sole plate
I. Spray nozzle
J. Anti-scale valve
To be cleaned once per month
K. Steam control
L. Express refilling drawer
A. Botón del rocío
Para humedecer la ropa
B. Botón de extra vapor
(según el modelo)
Para quitar las arrugas
C. Indicador luminoso autoapagado
automático (según el modelo)
D. Cordón de suministro eléctrico
E. Indicador luminoso de termostato
Se apaga cuando se alcanza la
temperatura deseada
F. Control del termostato
Para elegir la temperatura de planchado
G. Nivel máximo del depósito
No exceda de ese límite
H. Suela
I. Rocío
J. Varilla anticalcárea
Límpiese una vez al mes
K. Control de vapor
L. Tapa de llenado del depósito
A
A. Touche Vaporisation
Pour humidifier le linge
B. Touche Jet de vapeur puissant
(selon modèle)
Pour défroisser
C. Voyant Arrêt automatique
(selon modèle)
D. Cordon d’alimentation
E. Voyant du thermostat
S’éteint quand la température est
atteinte.
F. Commande du thermostat
Pour choisir la température de
repassage
G. Repère maxi du réservoir
Ne dépassez pas cette limite
H. Semelle
I. Vaporisateur
J. Tige anti-calcaire
A nettoyer une fois par mois
K. Commande vapeur
L. Volet d’ouverture du
réservoir
ULTRAGLIDE
ENGLISH
FRANCAISESPAÑOL
Be careful ! (depending on the model) Remove the soleplate protection before heating the iron.
¡ Cuidado ! (segun el modelo) Retire el protector de la suela antes de calentar la plancha.
Attention ! (selon modèle) Retirez le protecteur de semelle avant de faire chauffer le fer.
ENG
FR
ESP
B
C
D
E
F
G
H
I
J
K
L
NOT 032503 T-FAL GB/F/E 23/05/03 10:34 Page 1
IMPORTANT SAFEGUARDS
Read all instructions before using the iron.
When using your clothes iron, basic safety precautions should always be
followed, including the following :
11.1Use iron only for its intended use.
12.1To protect against a risk of electric shock, do not immerse the iron or the base
of the iron in water or other liquids.
13.1When fitted with an on/off switch the iron should always be turned OFF
before plugging or unplugging from outlet. Never yank cord to disconnect
from outlet ; instead, grasp plug and pull to disconnect.
14.1Do not allow cord to touch hot surfaces. Let iron cool completely before
putting away. Wrap cord loosely around iron when storing.
15.1Always disconnect iron from electrical outlet when filling with water or
emptying and when not in use.
16.1Do not operate iron with a damaged cord or if the iron has been dropped or
damaged. To avoid the risk of electric shock, do not disassemble the iron.
Contact our Consumer Service Department for examination, repair or
adjustment. Incorrect reassembly can cause a risk of electric shock when the
iron is in use.
17.1Close supervision is necessary for any appliance being used by or near
children. Do not leave iron unattended while connected or on an ironing
board.
18.1Burns can occur from touching hot metal parts, hot water or steam. Use
caution when you turn a steam iron upside down - there may be hot water in
the reservoir.
19.1This appliance is only for domestic and personal use.
SPECIAL INSTRUCTIONS
11.1To avoid a circuit overload, do not operate another high-wattage appliance on the
same circuit.
12.1If an extension cord is absolutely necessary, a 13 ampere cord should be
used.Cords rated for less amperage may overheat. Care should be taken to
arrange the cord so that it cannot be pulled or tripped over.
SAVE THESE INSTRUCTIONS
ENGLISH
NOT 032503 T-FAL GB/F/E 23/05/03 10:34 Page 2
- Unplug your iron before filling it.
- Set the steam control on DRY (A).
- Fill the beaker up to the line
indicated (B).
- Open the water tank filling inlet
completely (C), set the iron on a
table according to diagram (D) and fill
the reservoir.
- Do not exceed the MAX line indicated on the water reservoir (with the iron set on its heel).
- Close the Express refilling drawer.
A
C D
B
ENG
Warning ! Remove the sole plate protector before heating up the iron
(depending on the model).
What water to use ?
Your appliance has been designed to function with tap water. However, it is necessary to use the
Auto-Cleaning feature to clean the steam chamber regularly in order to eliminate hard water
deposits. If your water is very hard you may mix tap water with demineralized water in the
following proportions : 50% tap water, 50% demineralized water.
What water not to use :
Heat concentrates the elements contained in water during evaporation. The types of water
listed below contain organic waste or mineral elements that can cause spitting, brown staining, or
premature wear of the appliance: water from clothes dryers, scented or softened water, water
from refrigerators, batteries, or air conditioners, pure distilled water, or rain water. Do not use
any de-scaling agents in your iron, you may do permanent damage to the unit.
1- STEAM IRONING
Filling the water reservoir
- Set the temperature control
according to diagrams (E)
depending on model, and refer
to the table on the next page.
- Once plugged in, the indicator
light will turn on (F).
It automatically turns off when
the sole plate is sufficiently hot.
- In order to avoid dripping on fabrics:
Turn off the steam when ironing silk or synthetic fabrics.
Set it at the minimum position for wool.
G
Setting the steam (G)
Setting the temperature
E
F
Warning !
Prior to first use of your iron using steam on fabric, we recommend that you turn it
on for a few seconds in the horizontal position, and press the Burst of Steam button
several times.
During the first few uses, the iron may give off an odor and smoke; both are harmless.
This will not affect the use of the iron and will quickly disappear.
NOT 032503 T-FAL GB/F/E 23/05/03 10:34 Page 3
FABRIC
POSITION OF
THERMOSTAT CURSOR
STEAM SETTING
POSITION
COTTON
WOOL
SILK
SYNTHETIC
Polyester,Acetate,
Acrylic, Nylon
MIN
DRY
●●●
●●
= STEAM ZONE
Fabrics and ironing temperatures:
Your iron heats up quickly: begin by ironing fabrics that require a low temperature, then go on to
those requiring a higher temperature;
If you reduce the temperature, wait until the indicator light comes back on before ironing again.
When ironing fabrics with mixed fibres, set the temperature to the most delicate of the fibers.
H
- When steam or dry ironing, press several times on the Spray Button to moisten fabrics (H)
and to remove stubborn creases.
- Make sure that there is water in the reservoir before using this feature.
What temperature and which steam setting to use ?
Moistening the fabric (Spray)
LINEN
MAX
MAX
- Press the Burst of Steam button ( ) from time to time (I).
- Wait a few seconds before pressing the button again.
I
- The electronic system automatically cuts off the electric power and the Auto Shut off
indicator light blinks if the iron remains immobile on its heel for more than 8
minutes, or in a horizontal position for more than 30 seconds.
- To restart the iron, just shake it gently until the indicator light stops blinking.
Note : When the Auto Shut off security feature is on,
it is normal that the thermostat indicator light to be off.
M
Obtaining more steam for removing wrinkles
(depending on the model)
Vertical steam ironing
(depending on the model)
Auto Shut off security feature
(depending on the model)
J
K L
J
Recommendations:
- Hang the garment on a hanger and hold the fabric slightly taut with one
hand.
- Set the thermostat control on MAX (J).
- Press the Burst of Steam button ( ) repeatedly (K), moving the iron
from top to bottom (L).
- Hold the iron a few inches from the fabric to avoid burning delicate
fabrics.
NOT 032503 T-FAL GB/F/E 23/05/03 10:34 Page 4
CLEANING THE ANTI-SCALE VALVE
(Once per month) :
- Unplug your iron and empty the water reservoir through open filling drawer.
- To remove the anti-scale valve, pull it up using the handles located on each side (N).
NEVER TOUCH DOWN THE END OF THE VALVE.
- Soak the valve in a cup of white vinegar or plain lemon juice for 4 hours (O).
- Rinse with tap water.
- Place the steam control on dry.
- Replace the anti-scale valve.
THE IRON WILL NOT FUNCTION WITHOUT THE ANTI-SCALE VALVE.
USING THE SELF-CLEANING METHOD
In order to reduce scale build-up and extend the life of your iron, use the Self-Cleaning method once
per month.
- Unplug your iron and set the steam control on DRY .
- Pull filling tank drawer open and fill the water reservoir up to the max limit (see recommendations for the
types of water to use).
You shall leave the drawer open until you have finished the cleaning process.
- Place your iron on its heel and set the thermostat control on MAX.
- Plug in your iron and wait until the indicator light goes out.
- Unplug the iron and hold it over a sink in the horizontal position.
- Raise the anti-scale valve up to the hard point without removing it.
- Shake the iron gently, over the sink, until all of the water in the water reservoir (with the impurities) has
flowed out via the soleplate.
- At the end of the process, push the anti-scale valve back into position as well as the filling drawer.
- Turn the iron back on for 2 minutes, setting it on its heel, to dry the soleplate.
- Unplug the iron, and when the soleplate is lukewarm, wipe it with a soft cloth.
CLEANING THE SOLE PLATE
- While the sole plate is still lukewarm, clean it by rubbing it with a moist, non-metallic pad.
2- DRY IRONING
- Set the temperature.
- Set the steam control on DRY (see diagram A).
- You may start ironing when the indicator light goes out.
4- STORING YOUR IRON
- Unplug it and wait until the sole plate has cooled.
- Empty the water reservoir and set the steam control to DRY .
- Store the iron on its heel.
3- MAINTAINING YOUR IRON
BE CAREFUL !
Unplug your iron and let it cool off before cleaning.
N
O
Recommendation :
The self-cleaning function helps to delay scale build-up in your iron
and will aid in prolonging the iron’s life.
A
ENG
NOT 032503 T-FAL GB/F/E 23/05/03 10:34 Page 5
FOR YOUR SECURITY
• Warning! The voltage of your electrical installation must correspond to that of the iron (120V a.c).
Connecting to the wrong voltage may cause irreparable damage to the iron and will invalidate the
guarantee.
• If an extension cord is absolutely necessary, a 13 ampere cord should be used. Cords rated for less
amperage may overheat.
If the electrical cord becomes damaged, it must be immediately replaced. Please contact T-Fal’s
Consumer Service Department to avoid any danger.
Never immerse your iron in water!
The appliance must be unplugged before filling or emptying the water reservoir.
If the appliance falls, have it checked by a professional before using it again; unseen damages may
be dangerous.
The sole plate may be very hot:
- Never touch it.
- Always let it cool off before putting it away.
- Never leave your iron unattended when it is plugged in or while the sole plate is still hot.
- Always keep your iron out of the reach of children.
NEVER DISASSEMBLE YOUR IRON ON YOUR OWN ;
PLEASE REFER ALL SERVICE AND TECHNICAL QUESTIONS TO T-FAL’S
CONSUMER SERVICE DEPARTMENT.
NOT 032503 T-FAL GB/F/E 23/05/03 10:34 Page 6
ENG
5- TROUBLESHOOTING
Problems Possible Causes Solutions
Water drips from the holes
in the sole plate.
Brown streaks come through
the holes in the sole plate
and stain the fabrics.
The sole plate is dirty or
brown and and is staining
the fabric.
There is little or no steam.
The sole plate is scratched
or damaged.
The chosen temperature does
not allow for the formation of
steam.
You are using steam while the
iron is not hot enough.
You are using the burst of steam
button too often.
The steam flow is too high.
You have stored the iron
horizontally, without emptying it
and without setting it to DRY.
You are using chemical descaling
agents.
You are using pure distilled
water.
Fabric fibers have accumulated in
the holes of the soleplate and
are burning.
You are using too high a
temperature.
Your fabric is not rinsed
sufficiently or you are using
starch.
The water reservoir is empty.
•The anti-scale valve is dirty.
Your iron has a build-up of scale.
You iron has been used dry for
too long.
You have placed your iron flat on
a metallic rest-plate.
Set the thermostat in the
coloured zone (from ●● to
MAX).
Wait until the indicator light goes
out.
Wait a few seconds between each
use of the button.
Reduce the steam flow.
See the section "Storing your
iron".
Do not add any descaling agents
to the water in the water
reservoir.
Do a self-cleaning and use tap
water.
Do a self-cleaning.
Clean the soleplate with a non-
metallic sponge.
Vacuum the holes of the sole plate
from time to time.
Clean the soleplate as indicated
above. See the temperature table
to correctly set the thermostat.
Clean the soleplate as indicated
above.Always spray starch onto
the reverse side of the fabric to
be ironed.
Fill it with tap water.
Clean the anti-scale valve.
Clean the anti-scale valve and
do a self-cleaning.
Do a self-cleaning.
Always set your iron on its heel.
For all other problems or queries, please contact
our Consumer Service Department or an approved Service Centre
Phone number available on International Guarantee Card
NOT 032503 T-FAL GB/F/E 23/05/03 10:34 Page 7
032503 - 21/03
NOT 032503 T-FAL GB/F/E 23/05/03 10:34 Page 20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

T-Fal 1700 Serie Owner's manual

Category
Irons
Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI