2. Home
  3. Domestic appliances
  4. Climate control
  5. Household fans
  6. Casablanca
  7. La FLeur

Casablanca La FLeur Owner's manual

  • Hello! I am an AI chatbot trained to assist you with the Casablanca La FLeur Owner's manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
1
La FL e u r
™
INTRODUCTION
Before You Start 2
Safe Use 2
MOUNTING RECOMMENDATIONS
General Guidelines 3
Sloped Ceiling Installations 3
FAN INSTALLATION
Getting Started 4
Crossbar Mounting Bracket Installation 4
Lag Screw Installation (Optional) 5
Canopy Installation 5
Fan Preparation 6
Blade Installation 7
Hanging the Fan 7
Canopy Electrical Connections 8
Canopy Hatch Installation 8
Light Fixture Installation 9
Optional No-Light Cap Installation 9
PRIME-TOUCH W-505 CONTROL
Control Bracket Installation 10
Changing Transmitter Frequency Setting 11
Remote Operation 11
TROUBLESHOOTING TIPS 12
CARE RECOMMENDATIONS 13
PRODUCT SPECIFICATIONS 13
READ AND SAVE THESE INSTRUCTIONS!
SAFETY FIRST: Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the
product and proper installation. erefore, before attempting to install and operate your Casablanca fan, read this Owner’s
Manual completely and carefully. Retain the manual for future reference
CAUTION: To avoid possible electrical shock, make certain that electricity is turned off at the circuit breaker or fuse
box before attempting any installation procedure..
PN 8943891 AT0608
CONTENTS
La FL e u r Ow n e r ’s Ma n u a l
™
2
CIRCUIT BREAKER
Trip the breaker for
the circuit you will
be working on
FUSE BOX
Remove the fuse for
the circuit you will
be working on
SAFE USE
• Inspectthecontentsofyourcartonforpossibleshipping
or handling damage and report any such damage directly
to your authorized Casablanca dealer.
• Itisalwaysagoodideatohaveanassistanttohelpwith
the installation.
• e blades in each pack are matched for equal weight
to assure smooth fan operation. If more than one fan is
being installed, be careful not to mix blades from different
cartons.
• Neverinstallafanoverapoolorspa.
• Forsafetyreasons,thefanbladesmustbeaminimumof
7feetabovetheoor.
• Inanyinstallation,thetipsofthebladesmustbeatleast18
inchesfromthewallinordertoprovidesucientclearance
for the blades.
• Neverinsertanythingintothepathofthefanbladeswhile
the fan is in operation.
• When cleaning, painting, or working nearyour fan,be
verycarefulofthefanandblades.Alwaysturnthepower
OFFtotheceilingfanbeforeservicingit,workingonit,
or replacing lightbulbs.
• Neveroperateafanthathasbeendamagedinanyway.
For assistance inobtaining service,call CasablancaFan
Company toll-free at 1-888-335-5247 or contact your
local Casablanca Authorized Dealer.
BEFORE YOU START
• CAUTION:RISKOFELECTRICALSHOCK!InstallationistobeinaccordancewiththeNationalElectricalCode,
ANSI/NFPA 70-1999 and local codes. If you are unfamiliar with the wiring codes, you should use a qualified electrician.
Toavoidoverheatingandpossibledamagetootherequipment,donotinstallcontroltoareceptacle,uorescentlightxture,
motor operated appliance, or transformer-supplied appliance.
• isfanisdesignedtobeinstalledonanexistingelectricaloutletbox.eoutletboxmustbeULListedforceilingfan
installations,ifitisnot,anewboxmustbeinstalled.Casablancaextensionpolesareavailableforslopedorhighceiling
installations.
• isceilingfanrequiresagroundedelectricalsupplyof120VAC,60Hzandaminimum15ampcircuit.emaximum
currentrequirementforthefanwithlightxtureis3.8amps.efanusesabout1ampor100watts.Maximumlight
current is 2.0 amps or 120 watts of lighting.
•
Where wire nuts are employed, be sure all bare wires are within the connectors. When installing the canopy hatch, make
sure all wires are within the canopy and that no wires are being pinched.
• WARNING:Donotbendthebladebracketswheninstallingthebrackets,balancingthebladesorcleaningthefan.Do
not insert foreign objects in between the rotating fan blades.
• WARNING:Toreducetheriskofreorelectricshock,donotusethisfanwithanysolidstatespeedcontroldevice.Use
onlythecontrolprovidedwithorrecommendedforthisfan..
Unpacking
Beforeassemblingandinstallingyourceilingfan,removeallpartsfromtheshippingcartonsandcheckthemagainsttheparts
listedhere.Beforediscardingpackagingmaterial,becertainthatallpartshavebeenremoved.
NOTE: For best performance and for your warranty to be valid, use only genuine Casablanca Fan Company blades, light
fixtures, and accessories.
INTRODUCTION
18″
84″
3
La FL e u r
™
Ceiling Height Pole Length
8” Standard
8’6” Standard
9’0” 6”
9’6” 12”
10’0” 12”
11’0” 18”
12’0” 24”
13’0” 36”
14’0” 48”
BeforemountingyourCasablancafan,readthefollowinghelpfulrecommendations.elocationofthefan,aircirculation,
and fan size are all important factors to consider before installation.
Location
Ceilingfanshavepracticalusesinalmosteveryroominyourhome.Wesuggest
you follow these mounting recommendations as you decide where to install
your Casablanca fan.
• Donotlocatethefaninadoorwayoraboveaswingingdoor.
• Inbedrooms,fansworkbestwhenmountedabovethefootofthebed.
• Overpooltables,besuretoprovideplentyofclearancetoavoiddamagefrom
pool cues.
• In kitchens be sure to allow for open cupboard doors to clear the fan
blades.
• Donotinstallafancloseto,orover,apoolorspa.Highhumiditycombined
withcorrosivegaseswilldestroythenishandwarptheblades.
Fan Size
Variablefanspeedcapabilitypermitstheuseofafull-size52-inchfaneveninsmallerrooms.Forverylargerooms,twofans
may be needed.
7′ minimum
SUGGESTED EXTENSION POLE LENGTHS
When to Use Extension Poles
For best performance and appearance, an extension pole
should be used with your Casablanca fan when installing on
high (cathedral) ceilings or sloped ceilings. Casablanca offers
standard poles in increments of 6 inches up to 5 feet. Custom
polesareavailableinlengthsupto9feet9inches.Seeyour
Authorized Casablanca Dealer for details.
NOTE: efanmaywobbleorvibrateifthepolelength
is not long enough and the inside blade is too close to the
downslope or side wall. Extending the pole length usually
willsolvetheproblem.
Calculation of 32 Degrees
Use the tear-off Ceiling Angle Template card inserted in
thismanual.Itprovidesyouwithasimple“go”or“nogo”for
installing your fan on a sloped ceiling.
Blades must be a
minimum of 7′

Extension
Pole
Maximum Angle 32º
This slope is less than 32 degrees.
It is okay to install your fan.
SLOPED CEILING INSTALLATIONS
MOUNTING RECOMMENDATIONS
EXAMPLE 1
EXAMPLE 2
EXAMPLE 3
This slope is more than 32 degrees.Your
fan will not hang straight down; an adapter
is necessary. Contact your local Authorized
Casablanca Dealer to purchase a “Slope
Ceiling Adapter.”
This slope is 32 degrees, the maximum
slope that will allow the fan to hang
straight down. It is okay to install
your fan.
GENERAL GUIDELINES
ceiling outlet
box
support
brace
standard
mounting
style
32°
GETTING STARTED
Installing a New Ceiling Fixture Outlet Box
Ifyoudonothaveanexistingxturelocatedwhereyouwish
toplace yourCasablanca fan, anapprovedceiling xture
outlet box must be installed and wired.
Using Existing Ceiling Fixture Outlet Box
After turning the power OFF at its source (either the circuit
breaker or fuse box), lower the old fixture and disconnect the
wiring. Check the ceiling fixture outlet box to be sure that
itismarked“ApprovedForCeilingFanMounting.”Ifitis
not, a new box must be installed.
NOTE: eweightofthisfanis33pounds.
Wire Nut (4)
ADDITIONAL HARDWARE
2
1
/4” x 8-32 Rounded Head Screw (2)
Flat Washer (2)
1” x 8-32 Rounded
Head Screw (2)
Large Flat Washer
3
/
8
”(1)
Crossbar Mounting Bracket
Lag Screw
3
/
8
” #7 x 5” (1)
Joist
Ceiling
Wiring
Crossbar Mounting
Bracket
Green Ground Wire
Ceiling-Fan-Approved
Wiring Box
Ridge side down
NOTE: Afterremovingtheoldxture,checktheoutletbox
to ensure it is supported by a joist or beam across its upper
surface. If not, a 2 x 4 stud must be installed.
Step 1a.Removetheknockoutpluginthecenter ofthe
outlet box or drill a
1
/2-inch hole for the lag screw to pass
through.endrilla
1
/4-inch guide hole into the joist or
beam to a depth of 3 inches.
Step 1b. Route the outlet box wires through the keyhole
slot of the crossbar mounting bracket. Attach the crossbar
mountingbrackettooutletboxwiththescrewsprovided,
ensuring that the outlet box wires are not pinched by the
washer.
CROSSBAR MOUNTING BRACKET INSTALLATION
CEILING HARDWARE (not to scale)
4
FAN INSTALLATION
APPROVED
OUTLET BOX
HARDWARE
CAUTION: To reduce the risk of personal injury,
use only the mounting hardware provided with the
approved outlet box to install the crossbar mounting
bracket.
WARNING: To reduce the risk of fire, electrical
shock, or personal injury, mount to outlet box marked
“Acceptable Fan Support of 22 kg (50 lbs.) or less”
using the mounting hardware provided with the
outlet box.
WARNING!
Support directly to building structure only.
Step 3. Attach the canopy to the crossbar mounting bracket
with three of the 8-32 x 2
1
/
2
” long canopy screws and lock
washersprovidedwithyourCasablancafan.Tightenusingthe
providedscrewdriveruntilsnugagainsttheceiling.
NOTE: On sloped ceilings, align the canopy opening with
the top or peak of the room.
Canopy Screw
Canopy
Lock Washer
Feed outlet box wires
through canopy opening
Canopy Lock Washer (5)
Canopy Screw (5)
NOTE:is stepis requiredonly undertwo conditions:
If the fan weighs 35 lbs. or more (which does not pertain
to this fan) or if the existing ceiling fixture outlet box needs
to be modified for a ceiling fan application (for example, if
the house is not new construction and you are replacing an
existing light fixture). We recommend that the ceiling box be
ofsucientcapacitytosupporttheweightofthefanandlight
fixture under any conditions. If in doubt whether you need to
install the lag screw, consult a qualified electrician.
Step 2 (optional). With the large washer attached, pass the
lag screw through the center hole of the crossbar mounting
bracket and screw into guide hole. Tighten until outlet box
ismountedrmlytobeam.isboxmustbesecuredtothe
ceiling firmly.
Lag Screw
Large Washer
Canopy Hatch
Canopy
LAG SCREW INSTALLATION (OPTIONAL)
CANOPY INSTALLATION
CANOPY HARDWARE
(not to scale)
5
La FL e u r
™
6
Step 4a.Inordertoinstalltheblades,removetheveshipping
blocksattachedtotherotatingmotorplateusingtheprovided
screwdriver.SavethesescrewsforuseinStep4d.
Step 4b. Attach a two-piece blade medallion to each blade
by sandwiching the narrower end of a blade between a
medallion front and medallion back, threading the medallion
screws through the matching holes in the three pieces, and
tighteningthemedallionscrewssecurelyusingtheprovided
screwdriver.(Note:emedallionfrontshouldbeattached
to the side of the blade you want facing downward from the
ceiling.) Repeat for each blade assembly.
Step 4c. Attach a blade iron to each blade by threading two
B screws through the blade iron and blade badge screw holes,
thentighteningthescrewssecurelyusingtheprovidedAllen
wrench.
Step 4d. Attach each blade/blade iron assembly to the upper
edge of the motor by threading two C screws through the
matching holes in the blade iron and the motor, then tightening
thescrewssecurelyusingtheprovidedscrewdriver.
REMINDER:Fiveofthe10Cscrewsneededforthisstep
wereremovedfromtheshippingblocksinStep4a.
BLADE INSTALLATION
Reversible Blade (total of 5)
BLADE HARDWARE (not to scale)
Screw A for attaching
Medallion Front and Back
to Blade (4 per blade)
Screw B for attaching
Medallion to Blade
Iron (2 per blade)
Blade Iron
Medallion Front Medallion Back
Screw C for attaching
Blade Iron to Motor
Housing (2 per blade iron)
Screw A
Screw B
Screw C
Allen Wrench
Phillips Screwdriver
Shipping Block
7
La FL e u r
™
Prepareforfaninstallationasfollows:
Step 5a.Removethepapershieldfromthemotor.
Step 5b.Securethemotoradaptercoverplatewiththethree
providedscrews.
Step 5c.Routethewiresthroughthemotoradaptercover
and downrod.
Tip: e downrod has a tapered thread that is designed to
lock completely when installed correctly.
Step 5d.UsingtheprovidedAllenwrench(attachedtothe
paper motor warning shield), removethe Allen setscrew
from the hanger adapter and set it aside. Insert the downrod
into the motor coupling and turn it clockwise until it stops
turning, ensuring that the pole has bottomed out.
Step 5e.While holdingtheadapter motorcoversecurely,
insertthesetscrewandtightenitwiththeprovidedAllen
wrench to ensure safe operation of your fan. If it is tight
enough, you should not be able to turn the downrod
counterclockwise with your hands. If in doubt, tighten the
set screw with the Allen wrench until you cannot turn it any
further.
CAUTION: Failure to fully lock in the downrod
before securely tightening the Allen set screw may
cause the fan to separate from the downrod and fall
during normal operation.
IMPORTANT SAFETY INFORMATION:
Before starting the installation of your ceiling fan,
install the threaded downrod into the motor coupling
and lock the assembly
FAN PREPARATION
Motor
Coupling
Motor Wires
(leave at least 6 ” long)
Ground Wire
Allen
Set Screw

and Ball Assembly
Motor Adapter
Cover
Tapered
Thread
Motor Adapter
Cover Plate
Allen Set Screw
1
4
-20 X
1
4
” (pre-installed)
Allen Wrench

Ball Assembly
Motor Adapter Cover
Perma•Lock™ Hardware (not to scale)
Motor Adapter
Cover Plate
Motor Housing
Assembly
Motor Adapter Cover
Plate Screw
Motor Adapter
Cover Plate Screw
8
Canopy Washer
Canopy Screw
Canopy Hatch
Step 8a. Tuck the wires into the canopy
with the wire nuts pointed upwards, so
thattheWHITEandBLACKwiresare
on opposite sides of the canopy and all
wires are clear of the canopy opening.
Step 8b. Install canopy hatch with the last
canopy screw and lock washer using the
providedscrewdriver.Todothis,tiltthe
fan body away from the hatch opening.
Tighten the screws firmly.
Step 8c. Straighten the fan, then check
to ensure that there is no movement
between the canopy and the ceiling or
the Perma•Lock downrod and the ball
assembly.
CANOPY HATCH INSTALLATION
Step 7. Attach the fan wires to the ceiling fixture outlet box
wiring by placing the bare ends of the wires side by side and
then securing with a wire nut. Test that the connection is
securebypullingonthewirenut.Connectinthisorder:
• GREENleadsfrommountingplateanddownrodassembly
of fan to GROUND conductor of power source. Secure
with wire nut.
• WHITEwirefromfantowhiteNEUTRALwireinceiling
fixture outlet box. Secure with wire nut.
• BLACKpowerwirefromfantoBLACKpowerwirein
ceiling outlet box. Secure with wire nut
After making the wire connections, the wires should be spread
apart with the grounded conductor and the equipment-
grounding conductor on one side of the outlet box and the
ungrounded conductor on the other side of the outlet box.
NOTE: If the color of your ceiling wires differs from that
described, consult an electrician.
2 White Wires
2 Black Wires
Wire Nut
3 Green Wires
Tilt the fan to install last
canopy screw
Step 6a. To hang the fan body in the canopy, hold the fan body
firmly and insert the ball into the canopy opening. Check that
no wires were pinched. Rotate the fan body until the slot in
the ball fits into the pin opposite the canopy opening.
Step 6b.Trimexcessmotorwires,leavingatleast6inches
abovethedownrod.Strip
1
/2-inch insulation from the end of
eachwireusingawirestripper(availableatyourlocalhardware
store).esplicesafterbeingmadeshouldbeturnedupward
and pushed carefully into the outlet box.
Pin
Slot
Ball
HANGING THE FAN
CANOPY ELECTRICAL CONNECTIONS
9
La FL e u r
™
LIGHT FIXTURE INSTALLATION
Step 9a. Connect the two-pin connector from the light socket
center stem assembly to the two-pin receptor hanging from
the motor housing.
Step 9b. readeach ofthetwo providedscrews through
a screwhole in the light socket center stem assembly and
a screwhole in the motor housing and tighten using the
providedscrewdriver.
Step 9c.Insertaprovided60-wattG-16.5lightbulbintoeach
light socket and twist until snug.
Step 9d. Carefully lift the glass up to the light socket center
stem assembly and insert the threaded post of the assembly
into the hole in the glass. While continuing to hold the glass
up with one hand, screw the light fixture finial onto the
threaded post with the other hand.
WARNING! Do not allow the light socket center
stem assembly to hang by the wire.e fixture could
fall and cause injury or damage the fan.
Perma•Lock™ Hardware (not to scale)
Glass Shade
Light Socket Center
Stem Assembly
Light Fixture
Finial
OPTIONAL NO-LIGHT CAP INSTALLATION
If you choose not to install the light fixture, you must install
the no-light cap finial.
Step 9a. Tuck the wires inside the no-light cap finial, then
twist the finial onto the motor housing until tight.
No-Light
Cap Finial
60-watt g16.5 bulb
(Candelabra-base)
10
CONTROL BRACKET INSTALLATION
Screw
6-32 X
3
/
8
"
(2)
Wood
Screw
1" (2)
Drywall Anchor
6-32 (2)
12v Battery
W-505
Control
W-505
Control Bracket
SAFETYFIRST:Toreducetheriskofelectricalshock,thisfanmustbeinstalledwith
anisolatingwallcontrol/switch.CAUTION!Donotusewithwalldimmer.
 (not to scale)
Step 10. Follow instructions below for the type of
transmitter control you will be installing.
Standard Toggle Light Switch
a.Removethetwoscrewsholdingtheswitchcoverplate.
Donotremovethecoverplate.
b. Orient the control bracket as shown and line up the two
inner mounting holes with those on the switch.
c. Install and tighten screws using the provided
screwdriver.
Wall Installation
a.Locatea2x4wallstudinaconvenient-location.
b.Orientthecontrolbracketasshownoverthe2x4stud.
c. Use the 1-inch wood screws in the inner mounting
holes.Insertandtightenthescrewsusingtheprovided
screwdriver.
NOTE:ewallanchorsand6-32x1”screwsmaybe
used in situations where mounting to a stud is not possible.
Use the inner mounting holes. After securing the anchor,
discard the anchor’s pointed screws and use the supplied
6-32decorovalheadscrews.
CAUTION!Donotusewithwalldimmer.
is device complies with RSS-210 of Industry
Canada. Operation is subject to the following
two conditions: (1) This device may not cause
interference, and (2) is device must accept any
interference, including interference that may cause
undesired operation of the device.
NOTICE: Changes or modifications not expressly
approved in writing by Casablanca Fan Company
may void the user’s authority to operate this
equipment.
PrIme•ToUcH
TM
CONTROL INSTALLATION
11
La FL e u r
™
REMOTE OPERATION
CHANGING TRANSMITTER FREQUENCY SETTING
Send Signal
LED
Ifthefanisnotfunctioningafterinstallation:
Step 1. Check to make sure that batteries are installed correctly
in the control.
Step 2. Turn the power off to the fan (from the circuit breaker)
for at least 5 seconds.
Step 3. Turn the power back on (at the circuit breaker) and push
the HIGH, MED, and LOW buttons–in that order–within 20
seconds.
Step4.efanshouldnowfunctionproperly.
Youwillonlyhavetochangethedipswitchsettingsintheremote
if you are using more than one fan in the same area and want to
control them separately.
Step 1. At the circuit breaker or fuse box, turn the power off for
the fan you want to change.
Step2.OpenthebatterydoorofthePrime•Touchcontroland
removethebatteries.
Step 3. Change the dip switch settings, assuring that they are
dierentfromthepreviouslyinstalledPrime•Touchfan.
Step 4. Re-install the batteries and the battery door on the control.
Step 5. At the circuit breaker or fuse box, turn the power back
on for the fan whose frequency you are changing.
Step 6. Within 20 seconds of restoring power, push the HIGH,
MED, and LOW buttons (in that order).
Circuit Breaker
or Fuse Box
Press in this order to set new
frequency:
1. HIGH 2. MED 3. LOW
Dip Switch
Set to “0101”
Dip Switch
Set to “1000”
LOW
MED
HIGH
LIGHT
FAN
OFF
REVERSE
HigH 3
med 2
low 1
Note:Youmaywanttolabelyourcontrolstoassureyou
do not mix them up.
WARNING!
Do not turn the power off at the circuit breaker, then
backon,forthepreviouslyinstalledPrime•Touch2
fan(s), as you may inadvertently change the
frequency settings for it as well.
Note:Allfansleavethefactorysetto“0000.”
Fan Control
To start the fan, press the appropriate speed button to run the fan at the desired
speed.
•=Lowspeed••=Mediumspeed•••=Highspeed
To turn off the fan, press the FAN OFF button.
AirowDirection
Toreversetheairow,presstheREVERSEbutton.REVERSE operates at any speed,
whetherthefanisonoro.efanreturnstoitssetspeedafterreversing.
Light Control
Turn the light on or off independently from the fan by pressing the LIGHT button. If
youpressthebuttonformorethan0.7seconds,itbecomesadimmer.elightvaries
from“bright”to“dim”overapproximately8seconds.IfyoucontinuetoholdtheLIGHT
button,thissequencewillreversewhenthelightreachesthebrightestordimmestlevel.
Releasethebuttonwhenthedesiredlevelisreached.
12
Pleaserefertothisguidebeforerequestingserviceorcontactingyourdealerforassistance.
TROUBLESHOOTING TIPS
PROBLEM POSSIBLE REMEDIES
Fan will not start • Checkthemaincircuitfuses,circuitbreakers,andwallswitchposition.Checkall
wire connections. Make sure the power is turned off during this inspection.
• e9-pinconnectorisnotmakinggoodcontact.Checkthe9-pinconnectorin
thereceivermountedintheswitchhousing(seereceiverdiagramonpage11).
• ebatteryisweak.Installafreshbattery.
• efanreceiverisdefective.Replacefanreceiver.
• Checkthefrequencysetting:Turnthepoweroatthecircuitbreaker,onlyfor
the fan that is not functioning. Check that the jumper switches match in both the
receiverandthetransmitter.
Fan wobbles or shakes excessively • Besurethecanopypinissetproperlyintotheslotontheball.
• Checkthatthebladeholdershavenotbeenbentduringinstallationandtheblades
are balanced.
• ehangerbracketand/orceilingoutletareattachedtooloosely.Makesure
the hanger bracket is attached tightly to the ceiling outlet box and the downrod
assembly is secured firmly.
• edownrodisattachedtodownrodbasetooloosely.Makesureallthescrewsare
securely tightened.
Fan is noisy during operation
• Checkandtightenthelightxtureretainingscrews,glassshadescrews,and/or
lightbulb(s).
• Tightenthecanopyscrewsandmountingplateassembly.Makesurethewirenuts
inside the canopy and switch housing are not touching the metal parts and that
theyhavenotfallenothewiresplices.Tightenasnecessary.
• Tightenthebladeholderstotheywheel(ordirectdrivemotor)andthebladesto
the bladeholder screws.
• Makesureallscrewsinthemotorhousingaresnugbutnotoverlytight.
Fan does not run on low speed • Iffanisnew,itmayneedtobe“brokenin.”Runathighspeedforseveraldays.
Battery life is short • Replacewithalkalinebatteries.
Light works, but fan does not work • e9-pinconnectorisnotmakinggoodcontact.Checkthe9-pinconnector
receivermountedintheswitchhousing(seereceiverdiagramonpage11).
Fan and light run only on full speed • efanreceiverisdefective.Replacefanreceiver.
Fan is missing one speed • efanreceiverisdefective.Replacefanreceiver.
Fan does not change speed, but light works • efanreceiverisdefective.Replacefanreceiver.
Reverse does not work • efanreceiverisdefective.Replacefanreceiver.
Fan starts working by itself • ereisfrequencyinterference.ChangefrequencyasdescribedonPage11.
Fan operates only when transmitter is close • Checkthatantennawireisnottouchingmetalplate.
Fan works, but light does not dim • efanreceiverisdefective.Replacefanreceiver.
Fan works, but light does not work • efanreceiverisdefective.Replacefanreceiver.
• elightsocketisbroken.Replacesocket.
• Alightbulbisdefective.Replacelightbulb.
13
La FL e u r
™
For questions or to locate the nearest Casablanca Authorized Service Center,
call 1-888-335-5247 toll-free, or visit us on the Web at www.casablancafanco.com.
isdevicecomplieswithPart15oftheFCCrules.Operationissubjecttothefollowingtwoconditions:
1.isdevicemaynotcauseharmfulinterference.
2.This device must accept any interference received, including interference that may cause undesired operation.
isequipmenthasbeentestedandfoundtocomplywiththelimitsforaclassBdigitaldevice,pursuanttoPart15ofthe
FCCrules.eselimitsaredesignedtoprovidereasonableprotectionagainstharmfulinterferenceinaresidentalinstallation.
isequipmentgenerates,uses,andcanradiateradiofrequencyenergyand,ifnotinstalledandusedinaccordancewiththe
instructions,maycauseharmfulinterferencetoradiocommunication.However,thereisnoguaranteethattheinterference
willnotoccurinaparticularinstallation.Ifthisequipmentdoescauseharmfulinterferencetoradioortelevisionreception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
oneormoreofthefollowingmeasures:
• Reorientorrelocatethereceivingantenna.
• Increasetheseparationbetweentheequipmentandreceiver.
• Connecttheequipmentintoanoutletonacircuitdierentfromthattowhichthereceiverisconnected.
• Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
NOTE: Any changes or modifications to the transmitter or receiver not expressly approved by Casablanca Fan Company
may void one’s authority to operate this remote control.
CARE RECOMMENDATIONS
Fan Finishes
• Forcleaning,asoftbrushorlint-freeclothshouldbeusedtopreventscratchingthenish.
• Avacuumcleanerbrushnozzlecanremoveheavierdust.
• Surfacesmudgesoranaccumulationofdirtanddustcanberemovedeasilybyusingamilddetergentandslightlydampened
soft cloth. An antistatic agent may be used, but never use abrasive cleaning agents as these will damage the finish.
Blades
• Wood-nishbladesshouldbecleanedwithafurniturepolishingcloth.Occasionally,alightcoatoffurniturepolishmay
be applied for added protection and beauty.
• Forpaintedandhigh-glossblades,surfacesmudgesoranaccumulationofdirtanddustcanberemovedeasilybyusinga
mild detergent and slightly dampened soft cloth. An antistatic agent may be used, but never use abrasive cleaning agents
as these will damage the finish.
No Need for Lubrication
• Never lubricate this fan!
eprecisionmotorattheheartofyourCasablancafanfeaturessealedbearingsthatarelubricated
for life.
• Donotattempttooilthemotor.
Changing Lightbulbs
• BesuretoturnthepowertoOFFatthewallswitchorcircuitbreakerbeforechanginglightbulbs.
• Replacebulbswiththesametypeasyouremovedfromthelightxture.
• emaximumwattageratingforthisfan’slightkitis300watts.
PRODUCT SPECIFICATIONS
Collection: Cosmopolitan Collection by Casablanca
Model name: La Fleur
™
Model number: P2GxxH
Dimensions: A=12”
B=22”
C=3”
D=12.18”
E=5.6”
Weight:
33 lbs.
Motor: 188 x 20 mm - C1LT type
Blade span: 56 inches
Blade iron pitch: 15 degrees
No. of blades: 5
Technology: Prime•TouchW-505
Lightbulb type: (2) 60-watt G16.5 bulb (Candelabra-base)
Airflow: 5,900 cfm
Electricity Use: 69 watts
Airflow Efficiency: 86 cfm/watt
NOTE: Dimension
B includes light
fixture and glass.
/