Page is loading ...
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE ALL FASTENERS ARE TIGHT AND ALL STRUCTURAL COMPONENTS ARE SOUND
CURT Manufacturing Inc. warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective, Curt Manufacturing Inc. may repair or replace
the product at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. Curt Manufacturing Inc.'s liability is limited to repair or replacement
of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.
For more information log onto www curtmfg com & for helpful towing tips log onto www hitchinfo com
MAKE: STYLE:
MI N.30
WARNI NG: NEVER EXCEED YOUR VEHI CLE MANUFACTURER'S RECOMMENDED TOWI NG CAPACI TY
WEI GHT CARRYI NG:
I NSTALLATI ON TI PS: I NSTALLATION TI ME:
I NSTALLATION REQUI RES:
VEHICLE PHOTO:
HITCH I LLUSTRATION:
REPRESENTATIVE PHOTO
MAKE SURE YOUR HI TCH MATCHES
LEVEL OF DIFFI CULTY:
MODERATE
EASY MODERATE HARD
THE I NSTALL TI ME LISTED I S FOR PROFESSI ONAL
I NSTALLERS. I F YOU ARE HESITANT TO UNDERTAKE
THIS TASK ON YOUR OWN, CONTACT AN AUTHORI ZED
CURT I NSTALLER FOR ADDI TI ONAL ASSISTANCE.
1. BEFORE YOU BEGIN INSTALLATION, READ ALL
I NSTRUCTI ONS THOROUGHLY.
2. TO EASE I NSTALLATI ON, 2 PEOPLE MAY BE
REQUI RED.
3. USING PROPER TOOLS WILL GREATLY I MPROVE
THE QUALITY OF THE I NSTALL AND REDUCE THE
TI ME REQUIRED.
4. NEED HELP OR HAVE SOME QUESTI ONS?
CALL TECHNICAL SUPPORT AT 800.798.0813
Safety glasses should be
worn at all times while
installing this product
.
YEARS: 2010- CURRENT MERCEDES-BENZ MODEL: E-350 SEDAN SEDAN
2,000
200
TRAI LER WEI GHT:
TONGUE WEI GHT:
11001 I NSTALLATI ON I NSTRUCTI ONS
LBS.
LBS.
6/ 17/ 2014
WARNI NG:
WE RECOMMEND THE USE OF 1805 0 STABI LI ZI NG STRAPS FOR ALL NON-TRAI LER
( WHEEL- LESS) LOADS. PLEASE SEE THE CURT CATALOG OR VI SI T US ONLI NE AT
WWW.CURTMFG.COM FOR FURTHER I NFORMATI ON.
CENTER
PUNCH
POWER
DRI LL
MASKI NG
TAPE
17/ 32"
DRI LL BI T
TORQUE
WRENCH
RATCHET
SOCKET
EXTENSI ON
9"
SOCKET
3/ 4"
DRILLING REQUIRED
FISHWIRE REQUIRED
I NSTALLATI ON WALKTHROUGH:
For more information log ont o www.curt mfg.com, & for helpful towing t ips log onto www.hitchinfo.com
Parts List
DESCRIPTIONPART NUMBERQTYITEM
CARRIAGE BOLT1/2-13 x 1 1/421
HEX FLANGE NUTHFN 121342
HEX BOLT1/2 - 13 x 2 1/243
CONICAL TOOTHED WASHER1/2"44
1/2" FISHWIRE1_2 FISHWIRE25
CARRIAGE BOLT1/2 - 13 x 2"26
.250 x 1.00 x 3.00" SQUARE HOLE SPACERCM-SP627
1
2
3
4
5
7
6
1. Raise nut plate and mounting strap into position around
the vehicle crossmember. Secure using 1/2-13 x 2 1/2"
hex bolts and 1/2" conical toothed washers.
2. Raise hitch weldment past fascia lip and secure to mounting
strap using 1/2-13 x 1 1/4" carriage bolts and 1/2-13 flange
nuts.
I NSTALLATI ON WALKTHROUGH:
For more information log ont o www.curt mfg.com, & for helpful towing t ips log onto www.hitchinfo.com
3. Press hitch against the bottom of the bumper beam,
using the hitch as a template mark hole locations with
a center punch. Lower hitch and drill hole locations
with 17/32" drill bit.
4. Fishwire 1/2-13 x 2" carriage bolt and SP6 spacers through
access hole between the fascia and the back of the bumper
beam and out the holes drilled in Step 3. Raise hitch back
into position and secure with 1/2-13 flange nuts.
5. Torque 1/2" hardware to 75 ft-lbs.
6. Installation is now complete.
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.
* * * DO N OT E X CE ED V EH I CLE M ANU FACT U RE R'S REC OM M EN D ED T OWI NG CAP ACI T Y .* * *
WARNING: ALL NON-TRAILER LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED BY 18050 STABILIZING STRAPS.
* * FAI LURE T O PROP ERLY S UPPO RT N O N-T RAI LER L OA DS W ILL V OID P RODU CT W ARRAN TY* *
HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-877-287-8634
HITCH WEIGHT: LBS.
INSTALL TIME
PROFESSIONAL: MINUTES
NOVICE (DIY): MINUTES
INSTALL NOTES:
INSTALLATION STEPS
PERI ODI CALLY CHECK TH I S RECEIV ER H IT CH T O ENSURE T H AT ALL FAST EN ERS
ARE T I GHT AN D TH AT ALL STRUCT U RAL COM PONEN T S ARE SOUN D.
Curt Manufacturing Inc., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,
Curt Manufacturing Inc., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of
this product voids the warranty. Curt Manufacturing Inc.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or
consequential loss or damage.
2,000 200
26
30
MERCEDES BENZ E-350 SEDAN
4/13/2015
11001
60
Parts List
DESCRIPTIONPART NUMBERQTYITEM
NUT PLATE WELDMENTCM-NP1W11
CARRIAGE BOLT1/2-13 x 1 1/422
HEX FLANGE NUTHFN 121343
HEX BOLT1/2 - 13 x 2 1/244
CONICAL TOOTHED WASHER1/2"45
1/2" FISHWIRE1_2 FISHWIRE26
CARRIAGE BOLT1/2 - 13 x 2"27
.250 x 1.00 x 3.00" SQUARE HOLE SPACERCM-SP628
2
3
4
5
7
8
6
MOUNTING STRAP
BUMPER BEAM
FASCIA
NUT PLATE
VEHICLE CROSSMEMBER
TOOLS REQUIRED
RATCHET
RATCHET EXTENSION
3/4" SOCKET
DRILL
17/32" DRILL BIT
CENTER PUNCH
TORQUE WRENCH
- DRILLING REQUIRED
- FISHWIRE HARDWARE
DESIGNED FOR USE WITH
BALL MOUNT # D-55001/45501
1. Raise nut plate and mounting strap into position around the vehicle crossmember. Secure using 1/2-13 x 2 1/2"
hex bolts and 1/2" concial toothed washers.
2. Raise hitch weldment past fascia lip and secure to mounting strap using 1/2-13 x 1 1/4" carriage bolts and 1/2-13
flange nuts.
3. Press hitch against the bottom of the bumper beam, using the hitch as a template mark hole locations with a center
punch. Lower hitch and drill hole locations with 17/32" drill bit.
4. Fishwire 1/2-13 x 2" carriage bolt and SP6 spacers through the access holes between the fascia and the back of the
bumper beam and out the holes drilled in Step 3. Raise hitch back into position and secure with 1/2-13 flange nuts.
5. Torque all 1/2" hardware to 75 ft-lbs.
ACCESS HOLES
1
/