Dometic Waeco CA-800 Operating instructions

Page is loading ...

D

Fordern Sie weitere Informationen zur umfangreichen Produktpalette aus dem Hau-

se WAECO an. Bestellen Sie einfach unsere Kataloge kostenlos und unverbindlich

unter der Internetadresse: www.waeco.de

GB

We will be happy to provide you with further information about WAECO products.

Please order our free catalogue with no obligation to buy on our homepage:

www.waeco.com

F

Demandez d’autres informations relatives à la large gamme de produits de la

maison WAECO. Commandez tout simplement notre catalogue gratuitement et

sans engagement à l’adresse internet suivante : www.waeco.com

E

Solicite más información sobre la amplia gama de productos de la empresa WAE-

CO. Solicite simplemente nuestros catálogos de forma gratuita y sin compromiso en

la dirección de Internet: www.waeco.com

I

Per ottenere maggiori informazioni sull’ampia gamma di prodotti WAECO è possibi-

le ordinare una copia gratuita e non vincolante del nostro Catalogo all’indirizzo In-

ternet: www.waeco.com

NL

Maak kennis met het omvangrijke productscala van de firma WAECO. Bestel onze

catalogus gratis en vrijblijvend onder het internetadres: www.waeco.com

DK

Bestil yderligere information om det omfattende produktudvalg fra WAECO.

Bestil vores katalog gratis og uforpligtende på internetadressen: www.waeco.com

S

Inhämta mer information om den omfattande produktpaletten från WAECO:

Beställ våra kataloger gratis och utan förpliktelser under vår Internetadress:

www.waeco.com

N

Be om mer informasjon om det rikholdige produktutvalget fra WAECO. Bestill vår

katalog gratis uforbindtlig på Internettadressen: www.waeco.com

FIN

Pyytäkää lisää tietoja WAECOn kattavista tuotevalikoimista. Tilatkaa tuotekuvastom-

me maksutta ja sitoumuksetta internet-osoitteesta: www.waeco.com

CA-800-Install.book Seite 2 Freitag, 4. Mai 2007 4:56 16

3

CoolAi

r

1

209

401 291

2

1

6

4

5

1

2

3

CA-800-Install.book Seite 3 Freitag, 4. Mai 2007 4:56 16

CoolAi

r

4

5

1

2

3

5

4

6

CA-800-Install.book Seite 4 Freitag, 4. Mai 2007 4:56 16

5

CoolAi

r

6

min. 40 mm

365 mm

7

y

x

8

1

CA-800-Install.book Seite 5 Freitag, 4. Mai 2007 4:56 16

CoolAi

r

6

9

5

10

x

11

1562 3 4 7

8

CA-800-Install.book Seite 6 Freitag, 4. Mai 2007 4:56 16

Page is loading ...

Safety instructions

CoolAi

r

22

Contents

1 Safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

1.1 Using the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

1.1.1 Handling electrical cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

2 Conventions in this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

2.1 General information on the installation manual . . . . . . . . . . . . . . . . . . . . . . . . .24

2.2 Target group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

2.3 Symbols and formats. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

3 Intended use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

4 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

5 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

6 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

6.1 Installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

6.2 Installation steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

6.2.1 Make the roof hatch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

6.2.2 Prepare the system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

6.2.3 Secure the balance plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

6.2.4 Attach the sealing compound to the roof of the driver's cabin . . . . . . . . . . . . . . . . 29

6.2.5 Install the system in the roof hatch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

6.2.6 Lay the supply lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

6.2.7 Adjust the cover frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

6.2.8 Attach the cover frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

6.3 Configuration of system software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

6.3.1 Start and end configuration mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

6.3.2 Menu level 1: Set temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

6.3.3 Menu level 2: Low-voltage cut-off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

6.3.4 Menu level 3: Operating mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

6.3.5 Menu level 4: Default setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

7 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

1 Safety instructions

You must read the entire manual thoroughly and carefully.

We can only guarantee reliability of the roof air conditioner if the instruc-

tions are adhered to. The same applies to the prevention of injury and

damage to property.

WAECO International assumes no liability for damage resulting from the

following:

 Installation errors

 Damage to the system resulting from mechanical influences or overvolt-

age

 Alterations to the roof air conditioner made without the explicit permis-

sion of WAECO International

 Use for purposes other than those described in the installation manual

CA-800-Install.book Seite 22 Freitag, 4. Mai 2007 4:56 16

23

Safety instructions

CoolAi

r

1.1 Using the device

 Only use the roof air conditioner for the purpose specified by the manu-

facturer and do not make any alterations or structural changes to the

device.

 Only operate the roof air conditioner if you are certain that the housing

and the cables are not damaged.

 The roof air conditioner must be installed safely so that it cannot tip over

or fall down.

 Installation, maintenance and repair work may only be carried out by

qualified personnel from a specialist company who are familiar with the

risks involved and the relevant regulations.

 Do not use the roof air conditioner near flammable fluids or in closed

rooms.

 Do not reach into air grilles or ventilation nozzles or insert any foreign

objects in the system.

 Do not undo the upper cover of the roof air conditioner in the event of a

fire. Use approved extinguishing agents instead. Do not use water to

extinguish fires.

 Switch off the roof air conditioner before you use automatic washing

equipment (car washes, etc.) to clean the car!

 Please ask your vehicle manufacturer if the height entered in your vehi-

cle documents needs to be altered due to the extra height of the air con-

ditioning roof unit (extra height 209 mm).

 Disconnect all connections to the battery when carrying out work on the

device!

 Always manually drain the condensation before maintenance or tilting

the cab.

1.1.1 Handling electrical cables

 Use cable ducts to lay cables through walls with sharp edges.

 Do not lay loose or bent cables next to electrically conductive materials

(metal).

 Do not pull on the cables.

 Attach and lay the cables in such a manner that they cannot be tripped

over or damaged.

 The electrical power supply may only be connected by a qualified elec-

trician.

 Fit a fuse of at least 25 amps to the connection with the vehicle's power

supply.

 Never lay power supply lines (battery leads) in the vicinity of signal or

control wires.

CA-800-Install.book Seite 23 Freitag, 4. Mai 2007 4:56 16

Conventions in this manual

CoolAi

r

24

2 Conventions in this manual

2.1 General information on the installation manual

This installation manual contains the essential information and instructions

for installing the roof air conditioner. The information here is intended for

the company installing the roof air conditioner.

The following instructions are intended to help you use the installation

manual properly:

 The installation manual is part of the scope of delivery and should be

stored carefully.

 The installation manual provides you with important information on the

installation of the device and can also be used as reference material in

the event of repairs.

 The manufacturer (WAECO) assumes no liability for non-observance of

these installation instructions. Any claims are excluded in this case.

The operating manual for the CoolAir CA-800 can be found in the scope of

delivery for the roof air conditioner.

2.2 Target group

The installation and configuration information in this manual is intended for

qualified personnel at installation workshops who are familiar with the

guidelines and safety precautions to be applied during the installation of

vehicle accessory parts.

2.3 Symbols and formats

You will come across certain symbols and formats in this documentation.

This is what they mean:

Format Meaning Example

Bold Important information in the

text which may not be misun-

derstood

Set the switch (3) to the

COOLING symbol.

➤

Instruction text

➤ Lay the roof air conditioner

on a work surface with the

housing facing downwards.

✓ Results of an action ✓ The device is now ready for

operation.

CA-800-Install.book Seite 24 Freitag, 4. Mai 2007 4:56 16

25

Intended use

CoolAi

r

Indication of:

 Possible risks of injury to the fitter or user

and

 Possible damage to the device

Indicates a potentially dangerous situation which could arise during the in-

stallation or operation of the product and cause damage to the device or

environmental or economic damage.

Special information on handling the product

3 Intended use

The installation kit (item number: CA-EK-UNI1) enables you to install a

roof air conditioner CoolAir CA-800 (item number: CA-0800-DC) in the al-

ready existing roof hatch (ventilation hatch) of an HGV driver's cabin.

The roof air conditioner CA-800 is not suitable for installation in construc-

tion machines, agricultural machines or similar equipment. It does not work

properly in the event of strong vibrations.

The roof air conditioner CA-800 is designed for an ambient temperature of

less than 43 °C in cooling mode.

Operating the roof air conditioner CA-800 with voltages other than those

specified can result in damage to the device.

CA-800-Install.book Seite 25 Freitag, 4. Mai 2007 4:56 16

Scope of delivery

CoolAi

r

26

4 Scope of delivery

CA-800 installation kit for universal installation (existing roof hatch)

Item no. CA-EK-UNI1

5 Accessories

6Installation

The roof air conditioner may only be installed by qualified personnel from a

specialist company. The following information is intended for technicians

who are familiar with the guidelines and safety precautions to be applied.

6.1 Installation instructions

These installation instructions must be read completely prior to the installa-

tion of the roof air conditioner.

The following tips and instructions must be observed while installing the

roof air conditioner:

Make sure that all electrical components are electrically discharged before

carrying out work on them!

Part designation Quantity Item

number

Cover frame 1 4443000160

2,7 m insulating tape (profile: 25 x 25 mm) 1 –

2 m insulating tape (profile: 25 x 10 mm) 1 –

Fastening holder 2 4442500311

Balance plate 1 4442500305

Spacer sleeves L=3 mm 4 4443900170

Rubber buffer M8 4 4445200005

Cylindrical screw with Allen key M6 x 35 4 –

Washer M7 4 –

Self-locking nut M8 4 –

Nut M8 4 –

Washer M8 4 –

Installation manual 1 4445100204

Part designation Item number

Roof air conditioner CoolAir CA-800 CA-0800-DC

Hood for roof air conditioner CoolAir CA-800 CA-SH1

CA-800-Install.book Seite 26 Freitag, 4. Mai 2007 4:56 16

27

Installation

CoolAi

r

 You should always check whether any vehicle components could be

damaged or their function impaired by installing the roof air conditioner

before doing so. Using Fig. 1 on page 3 you can check the dimensions

of the installed system. The broken line here shows the middle of the

roof hatch.

 Before installation, find out (by consulting the manufacturer of the vehi-

cle) whether the construction is designed for the static weight and the

loads of the air conditioner when the vehicle is in motion. The manufac-

turer of the roof air conditioner (WAECO) assumes no liability whatso-

ever.

 The roof inclination of the mounting surface may not be more than 8° to

the front and 0° to the rear.

 The supplied assembly parts may not be modified by the customer

when installing them.

Improper installation of the roof air conditioner can result in irreparable

damage to the device and put the safety of the user at risk.

If the roof air conditioner is not installed according to the manufacturer's in-

structions, WAECO does not assume any liability. Waeco assumes no lia-

bility for malfunctions or for the safety of the roof air conditioner, especially

for personal injury and/or damage to property.

All connections to the battery of the vehicle should be disconnected before

installing the roof air conditioner.

Non-observance of this regulation can result in danger of electrocution.

After installing the system, the specified parameters of the system soft-

ware must be checked (see chapter "Configuration of system software" on

page 31).

6.2 Installation steps

WAECO International only assumes liability for parts included in the scope

of delivery. The validity of the warranty expires if the device is installed to-

gether with third-party parts.

Check whether the roof of the vehicle is able to support the weight of a

person before climbing onto it. Ask the vehicle manufacturer about the per-

mitted roof loads.

CA-800-Install.book Seite 27 Freitag, 4. Mai 2007 4:56 16

Installation

CoolAi

r

28

6.2.1 Make the roof hatch

➤ Remove all screws and fixtures of the existing sunroof.

➤ Take out the sunroof.

➤ Remove the sealing material from around the opening so that the sur-

face is clean and free of grease.

Dispose of all waste material, glue, silicone and seals separately. Observe

the disposal guidelines.

6.2.2 Prepare the system

While preparing the system on the work surface, make sure it does not fall.

Make sure that the surface is even and clean so that the system is not

damaged.

➤ Lay the roof air conditioner on a work surface with the housing facing

downwards.

➤ Remove the four M8 bolts, spring washers and washers from the four

threaded bolts (see fig. 2 on page 3, Pos. 1).

➤ Place the four spacer sleeves L= 3 mm (see fig. 3 on page 3, Pos. 4)

on the four threaded bolts (see fig. 3 on page 3, Pos. 6).

➤ Stick the 2 m long insulation tape (25 x 10 mm, see fig. 3 on page 3,

Pos. 5) into the existing cavity in the system. Apply a plastic, non-hard-

ening sealing compound (for example, SikaLastomer-710) to the im-

pact edge and the top edge of the insulation tape.

6.2.3 Secure the balance plate

➤ Position the balance plate on the system. To do this, place the four

thread bolts through the four slots in the balance plate.

The balance plate adjusts the roof air conditioner to the specific require-

ments of each vehicle.

➤ Screw one M8 nut each + spring washer + washer (see fig. 3 on

page 3, Pos. 1-3) on to the four thread bolts.

Handtighten the nuts.

➤ Screw one M8 bolt each (see fig. 5 on page 4, Pos. 1) on to the four

thread bolts until just in front of the already installed nut. The nut you

have now installed is used later to hold against the fastening holder

(see fig. 5 on page 4, Pos. 2).

CA-800-Install.book Seite 28 Freitag, 4. Mai 2007 4:56 16

29

Installation

CoolAi

r

6.2.4 Attach the sealing compound to the roof of the driver's

cabin

Make sure that the surface for sticking sealing compound between the bal-

ance plate and the roof of the driver's cabin is clean (free from dust, oil,

etc.).

➤ Stick the 2.7 m long insulating tape (25 x 25 mm) along the contour of

the roof hatch on the roof of the driver's cabin (see fig. 4 on page 4).

➤ Apply a plastic, non-hardening sealing compound (for example, Sika-

Lastomer-710) to the impact edge and the top edge of the insulation

tape.

6.2.5 Install the system in the roof hatch

➤ Position the fastening holder under the roof of the driver's cabin (see

fig. 6 on page 5). The fastening holders are pushed here between the

roof of the driver's cabin (chassis) and the roof interior.

The fastening holder must be positioned on a firm surface, as the system

is pushed through the holder against roof of the driver's cabin. The surface

for applying the fastening holder must be at least 40 mm on each side.

➤ Position the system in the sunroof opening centrally and in the direc-

tion of travel (see fig. 1 on page 3). The four thread bolts (see fig. 3 on

page 3, Pos. 6) must be placed into the four drill holes of the fastening

holder (see fig. 5 on page 4, Pos. 2).

Make sure the roof air conditioner is centred perfectly. The seal must be

applied continuously around the roof air conditioner after placing it on the

roof of the vehicle. This is the only way to ensure a tight seal.

➤ Screw one self-locking M8 nut each + M8 washer (see fig. 5 on

page 4, Pos. 3 and 4) on to the four thread bolts.

Do not exceed the specified torque. Only then can you avoid deforming

the fastening holder. Make sure that a high contact pressure is achieved

with minimum effort.

➤ Tighten the nuts with a torque of 3 Nm to attach the system.

➤ Now turn the M8 nut (see fig. 5 on page 4, Pos. 1) to tighten it against

the fastening holder.

➤ Screw the four rubber buffers on to the four thread bolts. The space

CA-800-Install.book Seite 29 Freitag, 4. Mai 2007 4:56 16

Installation

CoolAi

r

30

between the upper edge of the rubber buffer and the roof interior (con-

tact surface of the cover frame) must be calculated using the following

formula: (see fig. 7 on page 5): y = x - 7

The rubber buffers serve as a stop limit for the cover frame and you can

influence the installation position of the cover frame by turning the buffers

up or down.

6.2.6 Lay the supply lines

Make sure there is no voltage at electrically operated components before

carrying out work on them!

It is standard that the system has a 3.5 m long 4 mm

2

cable. If you require

longer cables, the cable cross section must be increased by an authorised

workshop:

Cut off the 4 mm

2

cable as closely as possible to the device (max. 0.5 m)

and then make a proper connection to a larger cable cross section.

WAECO recommends a cross section of 6 mm

2

from lengths of 3.5 m to

6m.

Fit a fuse of at least 25 amps to the connection with the vehicle's power

supply.

The roof air conditioner must be connected to a battery that is able to sup-

ply the required current (see chapter "Technical data" on page 35).

You can connect the system directly to both the HGV's multiplier and the

battery. However, connection to the multiplier is preferable. Ask your vehi-

cle manufacturer for the specifications of the multiplier.

➤ Lay the supply cable and connect it to the vehicle (red cable to plus

and black cable to minus).

➤ Plug the supply line plug into the socket in the roof air conditioner.

➤ Secure the supply line with a cable binder (see fig. 8 on page 5,

Pos. 1).

CA-800-Install.book Seite 30 Freitag, 4. Mai 2007 4:56 16

31

Installation

CoolAi

r

6.2.7 Adjust the cover frame

When the system is installed, the outlet unit must be approx. 5 mm above

the cover frame:

➤ Cut the cover frame to suit the specific conbditions of the vehicle (see

fig. 9 on page 6).

6.2.8 Attach the cover frame

Tighten the screws carefully so that the cover frame is not damaged.

The supplied cylindrical screws are suitable for the usual installation condi-

tions. If the length of the screws for attaching the cover frame is not suita-

ble, you can replace these by standard commercial screws of the same

type. Determine the required screw length as shown in Fig. 10 on page 6

(x = screw length).

➤ Attach the cover frame (see fig. 5 on page 4, Pos. 5) with the four cy-

lindrical screws + washers M7 (see fig. 5 on page 4, Pos. 6) to the

system.

6.3 Configuration of system software

Before you first start up the system, adapt the controls according to the in-

stallation conditions. This must be done by the person installing the sys-

tem.

In configuration mode, the following system software parameters must be

set on the control panel (see fig. 11 on page 6):

The configuration mode can also be called if the undervoltage protection

has switched off the system and there is only residual voltage.

Menu

level

Parameter Meaning Default

setting

1 Set temperature The system starts with the temper-

ature defined here.

20 °C

2 Low-voltage

cut-off

The battery monitor switches the

system off at the defined voltage.

ID number

4 = 23.5

Volt

3 Operating mode The system starts with the operat-

ing mode defined here.

0 =

Automatic

mode

4 Default

settings

The parameters 1-3 can be

returned to the default settings.

--

CA-800-Install.book Seite 31 Freitag, 4. Mai 2007 4:56 16

Installation

CoolAi

r

32

6.3.1 Start and end configuration mode

The adjustable parameters can be altered in edit mode:

➤ With the system switched off, press the ON/OFF button (see fig. 11 on

page 6, Pos. 1) and hold it down for 2-4 seconds.

➤ Additionally press the operating mode button (see fig. 11 on page 6,

Pos. 4) within these 2-4 seconds.

➤ Let go of the ON/OFF button.

➤ Hold the operating mode button pressed until the LED compressor

flashes.

✓ You are now in configuration mode.

✓ The first digit of the display (see fig. 11 on page 6, Pos. 5) shows the

menu level and the second and third show the parameter which can

be set – for example, 1.17 for menu level 1 and a set value of 17 °C.

If you make no entry on the control panel for 60 seconds, the system quits

configuration mode and switches off.

➤ Press the ON/OFF button to quit configuration mode.

6.3.2 Menu level 1: Set temperature

The system always starts with a defined value for the room temperature.

This parameter can be configured between 17 and 30 °C:

➤ Start configuration mode (see chapter "Start and end configuration

mode" on page 32).

✓ The first digit of the display (see fig. 11 on page 6, Pos. 5) shows the

menu level and the second and third show the parameter which can

be set.

➤ Press the operating mode button (see fig. 11 on page 6, Pos. 4) to

change the parameter.

➤ Use the +

or

-

buttons (

see fig. 11 on page 6

, Pos. 6 and 7)

to select

the temperature (in °C) with which the system starts.

✓ The digits in the display flash until the parameter you enter is con-

firmed.

➤ Press the operating mode button (see fig. 11 on page 6, Pos. 4) to

confirm your entry.

✓ The set value is saved and is then used when the system is restarted.

✓ You are now in menu level 1 and can use the + and - buttons to switch

between menu levels.

CA-800-Install.book Seite 32 Freitag, 4. Mai 2007 4:56 16

33

Installation

CoolAi

r

6.3.3 Menu level 2: Low-voltage cut-off

The battery monitor protects the battery from discharging too low.

When the the battery monitor switches the device off, the battery only has

a proportion of its charging capacity. Avoid starting repeatedly or operating

electrical consumers. Ensure that the battery is recharged. As soon as the

required voltage is available, you can restart the system.

If the roof air conditioner only has the supply voltage set here, the system

is switched off.

➤ Start configuration mode (see chapter "Start and end configuration

mode" on page 32).

✓ The first digit of the display (see fig. 11 on page 6, Pos. 5) shows the

menu level and the second and third show the parameter which can

be set.

➤ Press the

+

button (

see fig. 11 on page 6

, 6) once to switch to menu

level

2

.

➤ Press the operating mode button (see fig. 11 on page 6, Pos. 4) to

change the parameter.

✓ The digits in the display flash until the parameter you enter is con-

firmed.

➤ Press the +

or

-

buttons

(see fig. 11 on page 6

, Pos. 6 and 7)

to select

the value for the low voltage cut-off. The ID number displayed in the

second and third place of the digital display stands for the voltage at

which the system is switched off.

➤ Press the operating mode button (see fig. 11 on page 6, Pos. 4) to

confirm your entry.

✓ The set value is saved and is then used when the system is restarted.

✓ You are now in menu level 2 and can use the + and - buttons to switch

between menu levels.

ID

number

Low-voltage

cut-off

ID

number

Low-voltage

cut-off

1

23,2

6

23,7

2

23,3

7

23,8

3

23,4

8

23,9

4

23,5

9

24,0

5

23,6

10

24,1

CA-800-Install.book Seite 33 Freitag, 4. Mai 2007 4:56 16

Installation

CoolAi

r

34

6.3.4 Menu level 3: Operating mode

The system always starts with a defined operating mode for room temper-

ature. This parameter can be configured:

➤ Start configuration mode (see chapter "Start and end configuration

mode" on page 32).

✓ The first digit of the display (see fig. 11 on page 6, Pos. 5) shows the

menu level and the second and third show the parameter which can

be set.

➤ Press the

+

button (

see fig. 11 on page 6

, 6) twice to switch to menu

level

3

.

➤ Press the operating mode button (see fig. 11 on page 6, Pos. 4) to

change the parameter.

✓ The digits in the display flash until the parameter you enter is con-

firmed.

➤ Use the

buttons

+

or

-

(

see fig. 11 on page 6

, Pos. 6 and 7)

to select

the operating mode with which the system starts.

➤ Press the operating mode button (see fig. 11 on page 6, Pos. 4) to

confirm your entry.

✓ The set value is saved and is then used when the system is restarted.

✓ You are now in menu level 3 and can use the + and - buttons to switch

between menu levels.

ID number Operating mode

0

Automatic mode

1

Operating mode 1

2

Operating mode 2

3

Operating mode 3

CA-800-Install.book Seite 34 Freitag, 4. Mai 2007 4:56 16

35

Technical data

CoolAi

r

6.3.5 Menu level 4: Default setting

You can return the parameters you set in configuration mode on menu lev-

els 1 to 3 to the default settings:

➤ Start configuration mode (see chapter "Start and end configuration

mode" on page 32).

✓ The first digit of the display (see fig. 11 on page 6, Pos. 5) shows the

menu level and the second and third show the parameter which can

be set.

➤ Press the

+

button (

see fig. 11 on page 6

, 6) three times to switch to

menu level

4

.

✓ The digital display shows

--.

➤ Press the operating mode button (see fig. 11 on page 6, Pos. 4) to

return the system to its default settings.

✓ The digits in the display

-- flash.

➤ Press the

+

button.

✓ The digital display shows 00.

➤ Press the operating mode button (see fig. 11 on page 6, Pos. 4) to

confirm your entry.

✓ The parameters set in configuration mode are returned to the default

setting.

✓ You are now in menu level 4 and can use the + and - buttons to switch

between menu levels.

7 Technical data

Versions, technical modifications and delivery options reserved.

Roof air conditioner CoolAir CA-800

Item number CA-0800-DC

Cooling capacity: 800 W

Rated input voltage: 24 V DC

Input voltage range: 20 V DC – 30 V DC

Average current consumption: 12 – 22 A

Low-voltage cut-off: Configurable (see chapter "Menu level 2: Low-

voltage cut-off" on page 33)

Dimensions (L x W x H in mm): 690 x 565 x 209

(Height above vehicle roof)

Weight (without balance plate): 20 kg

CA-800-Install.book Seite 35 Freitag, 4. Mai 2007 4:56 16

Page is loading ...

Europe

WAECO Schweiz AG

Riedackerstrasse 7a

CH-8153 Rümlang (Zürich)

℡ +41 44 8187171

 +41 44 8187191

Mail: [email protected]

WAECO Danmark A/S

Tværvej 2

DK-6640 Lunderskov

℡ +45 75585966

 +45 75586307

Mail: [email protected]

WAECO Ibérica S.A.

Camí del Mig, 106

Poligono Industrial Les Corts

E-08349 Cabrera de Mar

(Barcelona)

℡ +34 93 7502277

 +34 93 7500552

Mail: [email protected]

WAECO Distribution SARL

ZAC 2 · Les Portes de L‘Oise

Rue Isaac Newton

F-60230 Chambly (Paris)

℡ +33 1 30282020

 +33 1 30282010

Mail: [email protected]

WAECO Finland OY

Mestarintie 4

FIN-01730 Vantaa

℡ +358 20 7413220

 +358 9 7593700

Mail: [email protected]

WAECO Italcold SRL

Via dell’Industria 4/0

I-40012 Calderara di Reno (BO)

℡ +39 051 727094

 +39 051 727687

Mail: [email protected]

WAECO Norge AS

Leif Weldingsvei 16

N-3208 Sandefjord

℡ +47 33428450

 +47 33428459

Mail: [email protected]

WAECO Benelux B.V.

Ecustraat 3

NL-4879 NP Etten-Leur

℡ +31 76 5029000

 +31 76 5029090

Mail: [email protected]

WAECO Svenska AB

Gustaf Melins gata 7

S-42131 Västra Frölunda

(Göteborg)

℡ +46 31 7341100

 +46 31 7341101

Mail: [email protected]

WAECO UK Ltd.

Dorset DT2 8LY · Unit G

Roman Hill Business Park

UK-Broadmayne

℡ +44 1305 854000

 +44 1305 854288

Mail: [email protected]

CH

DK

E

F

FIN

I

N

NL

S

UK

Overseas + Middle East

WAECO Pacific Pty. Ltd.

1 John Duncan Court

Varsity Lakes QLD 4227

℡ +61 7 55076000

 +61 7 55076001

Mail: [email protected]

WAECO Impex Ltd.

Suites 3210-12 · 32/F · Tower 2

The Gateway · 25 Canton Road

Tsim Sha Tsui · Kowloon

Hong Kong

℡ +852 24632750

 +852 24639067

Mail: [email protected]

WAECO Impex Ltd.

Taipei Office

2 FL-3 · No. 56 Tunhua South Rd, Sec 2

Taipei 106, Taiwan

℡ +886 2 27014090

 +886 2 27060119

Mail: [email protected]

WAECO Middle East FZCO

R/A 8, SD 6

Jebel Ali, Dubai

℡ +971 4 8833858

 +971 4 8833868

Mail: [email protected]

WAECO USA, Inc.

8 Heritage Park Road

Clinton, CT 06413

℡ +1 860 6644911

 +1 860 6644912

Mail: [email protected]

AUS

HK

ROC

UAE

USA

Headquarters

WAECO International GmbH · Hollefeldstraße 63 · D-48282 Emsdetten

℡ +49 2572 879-195 ·  +49 2572 879-322 · Mail: [email protected] · Internet: www.waeco.de

D

www.waeco.com

4445100204 05/2007

CA-800-Install.book Seite 157 Freitag, 4. Mai 2007 4:56 16

Dometic Waeco CA-800 Operating instructions

This manual is also suitable for

Dometic Waeco CA-800 Operating instructions

in other languages

Related papers

Other documents