Page is loading ...
Digital Video Recorder
i
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert
the user to the presence of uninsulated "dangerous voltage" within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the presence
of important operating and maintenance (servicing) instructions in the literature accompanying
the appliance.
Symbol
Publication
Description
IEC60417, No.5032
Alternating current
IEC60417, No.5031
Direct current
COMPLIANCE NOTICE OF FCC:
THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL
DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE
REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN
A COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE RADIO
FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION
MANUAL, MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS. OPERATION OF THIS
EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL INTERFERENCE, IN WHICH CASE
USERS WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT THEIR OWN EXPENSE.
WARNING: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR
COMPLIANCE COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
THIS CLASS OF DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE-
CAUSING EQUIPMENT REGULATIONS.
The information in this manual is believed to be accurate as of the date of publication even though explanation about
some functions may not be incorporated. We are not responsible for any problems resulting from the use thereof. The
information contained herein is subject to change without notice. Revisions or new editions to this publication may be
issued to incorporate such changes.
The software included in this product contains some Open Sources. You may obtain the complete corresponding source
code from us. See the Open Source Guide on the software CD (OpenSourceGuide\OpenSourceGuide.pdf) or as a printed
document included along with the User's Manual.
User’s Manual
ii
Important Safeguards
1. Read Instructions
All the safety and operating instructions should be read before the
appliance is operated.
2. Retain Instructions
The safety and operating instructions should be retained for future
reference.
3. Cleaning
Unplug this equipment from the wall outlet before cleaning it. Do
not use liquid aerosol cleaners. Use a damp soft cloth for cleaning.
4. Attachments
Never add any attachments and/or equipment without the approval
of the manufacturer as such additions may result in the risk of fire,
electric shock or other personal injury.
5. Water and/or Moisture
Do not use this equipment near water or in contact with water.
6. Placement and Accessories
Do not place this equipment on an unstable cart,
stand or table. The equipment may fall, causing
serious injury to a child or adult, and serious
damage to the equipment.
This equipment and cart combination should be
moved with care. Quick stops, excessive force,
and uneven surfaces may cause the equipment and cart
combination to overturn.
Do not place this equipment on a closed space. Sufficient amount of
ventilation air is necessary to avoid increase of ambient temperature
which can cause improper operation or the risk of fire.
7. Power Sources
This equipment should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of power,
please consult your equipment dealer or local power company.
You may want to install a UPS (Uninterruptible Power Supply)
system for safe operation in order to prevent damage caused by an
unexpected power stoppage. Any questions concerning UPS,
consult your UPS retailer.
8. Power Cords
Operator or installer must remove power and TNT connections before
handling the equipment.
9. Lightning
For added protection for this equipment during a lightning storm, or
when it is left unattended and unused for long periods of time, unplug
it from the wall outlet and disconnect the antenna or cable system. This
will prevent damage to the equipment due to lightning and
power-line surges.
10. Overloading
Do not overload wall outlets and extension cords as this can result
in the risk of fire or electric shock.
11. Objects and Liquids
Never push objects of any kind through openings of this equipment
as they may touch dangerous voltage points or short out parts that
could result in a fire or electric shock. Never spill liquid of any kind
on the equipment.
12. Servicing
Do not attempt to service this equipment yourself. Refer all servicing
to qualified service personnel.
13. Damage requiring Service
Unplug this equipment from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
A. When the power-supply cord or the plug has been damaged.
B. If liquid is spilled, or objects have fallen into the equipment.
C. If the equipment has been exposed to rain or water.
D. If the equipment does not operate normally by following the operating
instructions, adjust only those controls that are covered by the
operating instructions as an improper adjustment of other controls
may result in damage and will often require extensive work by a
qualified technician to restore the equipment to its normal operation.
E. If the equipment has been dropped, or the cabinet damaged.
F. When the equipment exhibits a distinct change in performance –
this indicates a need for service.
14. Replacement Parts
When replacement parts are required, be sure the service technician
has used replacement parts specified by the manufacturer or that have
the same characteristics as the original part. Unauthorized substitutions
may result in fire, electric shock or other hazards.
15. Safety Check
Upon completion of any service or repairs to this equipment, ask the
service technician to perform safety checks to determine that the
equipment is in proper operating condition.
16. Field Installation
This installation should be made by a qualified service person and
should conform to all local codes.
17. Correct Batteries
Warning: Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
18. Tmra
A manufacturer’s maximum recommended ambient temperature (Tmra)
for the equipment must be specified so that the customer and installer
may determine a suitable maximum operating environment for the
equipment.
WEEE (Waste Electrical & Electronic Equipment)
Correct Disposal of This Product
(Applicable in the European Union and other European countries with separate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at
the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal,
please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material
resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for
details of where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product
should not be mixed with other commercial wastes for disposal.
Digital Video Recorder
iii
Table of Contents
Chapter 1 — Configuration ................................................................................................................ 1
Turning on the Power .................................................................................................................... 1
Initial Unit Setup ............................................................................................................................ 1
Setup Screen ................................................................................................................................ 2
System Setup ................................................................................................................................ 3
General ..................................................................................................................................... 3
Date/Time ............................................................................................................................... 12
User ........................................................................................................................................ 13
Storage ................................................................................................................................... 15
System Event ......................................................................................................................... 16
Recording Setup ......................................................................................................................... 17
General ................................................................................................................................... 17
Schedule ................................................................................................................................. 18
Pre-Event ................................................................................................................................ 20
Event Setup................................................................................................................................. 21
Motion ..................................................................................................................................... 21
Alarm-In .................................................................................................................................. 23
Video Loss .............................................................................................................................. 23
Video Blind ............................................................................................................................. 24
Text-In .................................................................................................................................... 25
Camera Setup ............................................................................................................................. 27
General ................................................................................................................................... 27
PTZ ......................................................................................................................................... 28
Device Setup ............................................................................................................................... 29
Audio ...................................................................................................................................... 29
Alarm-Out ............................................................................................................................... 30
Remote Control ...................................................................................................................... 31
Network Setup............................................................................................................................. 32
General ................................................................................................................................... 32
LAN ......................................................................................................................................... 33
FEN ........................................................................................................................................ 35
RTSP ...................................................................................................................................... 36
WebGuard .............................................................................................................................. 37
VNC ........................................................................................................................................ 37
NetFS ..................................................................................................................................... 38
Notification Setup ........................................................................................................................ 40
Callback .................................................................................................................................. 40
Mail ......................................................................................................................................... 40
SNS ........................................................................................................................................ 42
FTP ......................................................................................................................................... 43
Schedule ................................................................................................................................. 44
Display Setup .............................................................................................................................. 45
OSD ........................................................................................................................................ 45
Main Monitor ........................................................................................................................... 46
Chapter 2 — Operation.................................................................................................................... 47
Turning on the Power .................................................................................................................. 47
Live Monitoring ............................................................................................................................ 47
Live Monitoring Menu ............................................................................................................. 48
Active Cameo Mode ............................................................................................................... 49
Zoom Mode ............................................................................................................................ 50
User’s Manual
iv
PTZ Mode ............................................................................................................................... 50
Event Monitoring ..................................................................................................................... 51
Covert Camera ....................................................................................................................... 51
Status Monitoring .................................................................................................................... 52
Recording Video.......................................................................................................................... 53
Panic Recording ..................................................................................................................... 53
Recording Audio.......................................................................................................................... 54
Playing Recorded Video.............................................................................................................. 54
Searching Video .......................................................................................................................... 55
Search Menu .......................................................................................................................... 55
Event Log Search ................................................................................................................... 57
Record Table Search .............................................................................................................. 59
Motion Search ........................................................................................................................ 60
Text-In Search ........................................................................................................................ 62
Bookmarks .............................................................................................................................. 63
Clip-Copy ................................................................................................................................ 64
Print ........................................................................................................................................ 66
Appendix .......................................................................................................................................... 67
USB Hard Disk Drive Preparation ............................................................................................... 67
Text-In Search Examples ............................................................................................................ 67
Search Example I ................................................................................................................... 67
Search Example II .................................................................................................................. 68
WebGuard ................................................................................................................................... 69
Web Monitoring Mode ............................................................................................................ 70
Web Search Mode .................................................................................................................. 71
Time Overlap ............................................................................................................................... 73
Error Code Notices ...................................................................................................................... 73
System Log Notices .................................................................................................................... 74
Map of Screens ........................................................................................................................... 75
Troubleshooting .......................................................................................................................... 76
Specifications .............................................................................................................................. 76
List of Illustrations
Figure 1: Login screen. ...................................................................................................................... 1
Figure 2: Logout screen. .................................................................................................................... 1
Figure 3: Setup screen. ..................................................................................................................... 2
Figure 4: System – General setup screen. ........................................................................................ 3
Figure 5: System – Date/Time setup screen. .................................................................................. 12
Figure 6: System – User setup screen. ........................................................................................... 13
Figure 7: System – Storage setup screen. ...................................................................................... 15
Figure 8: System – System Event setup screen. ............................................................................. 16
Figure 9: Record – General setup screen........................................................................................ 17
Figure 10: Record – Schedule setup screen. .................................................................................. 18
Figure 11: Schedule – Settings (Advanced Mode) setup screen..................................................... 19
Figure 12: Record – Pre-Event setup screen. ................................................................................. 20
Figure 13: Event – Motion setup screen. ......................................................................................... 21
Figure 14: Event – Alarm-In setup screen. ...................................................................................... 23
Figure 15: Event – Video Loss setup screen. .................................................................................. 23
Digital Video Recorder
v
Figure 16: Event – Video Blind setup screen................................................................................... 24
Figure 17: Event – Text-In setup screen.......................................................................................... 25
Figure 18: Camera – General setup screen. ................................................................................... 27
Figure 19: Camera – PTZ setup screen. ......................................................................................... 28
Figure 20: Device – Audio setup screen. ......................................................................................... 29
Figure 21: Device – Alarm-Out setup screen................................................................................... 30
Figure 22: Device – Remote Control setup screen. ......................................................................... 31
Figure 23: Network – General setup screen. ................................................................................... 32
Figure 24: Network – LAN setup screen. ......................................................................................... 33
Figure 25: Network – FEN setup screen.......................................................................................... 35
Figure 26: Network – RTSP setup screen. ...................................................................................... 36
Figure 27: Network – WebGuard setup screen. .............................................................................. 37
Figure 28: Network – VNC setup screen. ........................................................................................ 37
Figure 29: Network – NetFS. ........................................................................................................... 39
Figure 30: Notification – Callback setup screen. ............................................................................. 40
Figure 31: Notification – Mail setup screen...................................................................................... 40
Figure 32: Notification – SNS setup screen. .................................................................................... 42
Figure 33: Notification – FTP setup screen. .................................................................................... 43
Figure 34: Notification – Schedule setup screen. ............................................................................ 44
Figure 35: Display – OSD setup screen. ......................................................................................... 45
Figure 36: Display – Main Monitor setup screen. ............................................................................ 46
Figure 37: Live Monitoring menu. .................................................................................................... 47
Figure 38: PTZ Select Camera menu. ............................................................................................. 50
Figure 39: PTZ Preset menu. .......................................................................................................... 50
Figure 40: Event Status – Event Status screen. .............................................................................. 52
Figure 41: Event Status – Storage screen. ...................................................................................... 53
Figure 42: Select Playback Camera menu. ..................................................................................... 54
Figure 43: Search menu. ................................................................................................................. 55
Figure 44: Event Log Search screen. .............................................................................................. 57
Figure 45: Record Table Search screen. ......................................................................................... 59
Figure 46: Motion Search screen..................................................................................................... 60
Figure 47: Text-In Search screen. ................................................................................................... 62
Figure 48: Bookmarks screen. ......................................................................................................... 63
Figure 49: Clip-Copy screen. ........................................................................................................... 64
Figure 50: Print screen. ................................................................................................................... 66
User’s Manual
vi
Digital Video Recorder
1
Chapter 1 — Configuration
Turning on the Power
Connecting the power cord to the DVR turns on the unit. The unit takes approximately 50 seconds to initialize.
Initial Unit Setup
Before using your DVR for the first time, you will want to establish the initial settings. This includes items such as
time and date, display language, camera, remote control, record mode, network and password. Your DVR can be set
up using various screens and dialog boxes.
Throughout the screens you will see . Highlighting the and pressing the button gives you the opportunity
to reset that screen to its default settings.
Highlighting This page or All pages and pressing the button resets the current
page or all pages of the screen to its or their default settings.
After you are finished with any setup screen, you can highlight Save and press the button to save the changes
and exit the screen. If you do not wish to save the changes, highlight Cancel and press the button to exit the
screen.
Press the MENU button or move the mouse pointer on the right edge of the screen and then select (Login) in the Live
Monitoring menu to enter the setup screens. The Login screen appears.
Select a User and enter the password by pressing the appropriate
combination of Camera number buttons and then the button.
There is no default password when logging in the admin user for
the first time. If you do not know the password, click the button for
guidance.
Figure 1: Login screen.
NOTE:
To assure the secure management of the system, setting up a password is strongly recommended.
If you cannot use the front panel buttons, click the
button using the mouse to enter a password, and
the virtual keyboard displays. See instructions below for using the virtual keyboard.
To log the user out of the system, press the MENU button or move the mouse pointer on the right edge
of the screen and then select (Logout) in the Live Monitoring menu. The Logout screen displays asking
you to confirm whether or not you want to log out the current user.
Figure 2: Logout screen.
User’s Manual
2
Setup Screen
System
Record
Event
Camera
Device
Network
Notification
Display
Figure 3: Setup screen.
Press the MENU button or move the mouse pointer on the right edge of the screen and then select (Setup) in the Live
Monitoring menu to enter the setup screen.
While setting up the DVR, there will be many opportunities to enter names and titles. When making these entries, a
Virtual Keyboard will appear.
Use the arrow keys to highlight the character you want in the name or title and press
the button. That character appears in the title bar and the cursor moves to the
next position. Pressing toggles between the upper and lower case keyboards,
backspaces, and deletes entered characters. Pressing toggles between
different keyboard layouts. You can use up to 31 characters including spaces in
your title.
Special characters can be created using ^ and a capital letter; e.g., ^J for NL (New
Line), ^M for CR (Carriage Return). Special characters are commonly used by text
input devices and will be useful when performing Text-In Searches.
Digital Video Recorder
3
System Setup
General
Figure 4: System – General setup screen.
Highlight the Site box and press the button. A virtual keyboard appears that you can use to enter a Site Name.
Once you have entered your title, highlight OK and press the button.
Highlight the box beside System ID and press the button. Change the number by highlighting it and using the
Up and Down arrow buttons to increase and decrease the number from 0 to 99.
NOTE:
The System ID number is used to identify the unit when it is connected with other DVRs through the RS485
port. You cannot use the same ID number for two or more DVRs that are in the same RS485 network.
It is possible to have multiple DVRs with System ID 0 that are in the same area as long as they are not
part of an RS485 network. If this is the case, all will be controlled at the same time when using the infrared
remote control.
Highlight the box beside Language and press
button. A drop-down menu displays the available languages.
Highlight the desired language and press the button.
User’s Manual
4
The box beside Version displays the software version of the DVR. To upgrade the software, connect a USB device
containing the upgrade package file to the DVR. If you enabled the NetFS function (Network menu > NetFS tab),
you can download the file from the registered NetFS site. Highlight Upgrade… and press the button. Select
USB Storage or NetFS. If you select NetFS, select a NetFS site from the registered NetFS site list. The Upgrade
screen appears. The screen displays the upgrade package file names that are available. The “.rui” indicates that the file
is for software upgrades.
Select the desired file and press the button. Highlighting the Install button and pressing the button will
install the selected software package. Highlighting the Cancel button and pressing the button will close the
window without upgrading the software. If the upgrade package file is not installed on the DVR properly, you will get
an error message. The system restarts automatically after completing the upgrade.
CAUTION:
The USB device must be FAT16 or FAT32 format.
You can import saved DVR settings or export the current DVR settings. To import saved DVR settings, connect the
USB device containing the setup file (.dat) to the DVR. If you enabled the NetFS function (Network menu > NetFS
tab), you can download the setup file from the registered NetFS site. Highlight Setup – Import… and press the
button. Select USB Storage or NetFS. If you select NetFS, select a NetFS site from the registered NetFS site
list. Select the desired setup file and press the Import button to import the selected settings and change the DVR settings
accordingly. Highlight Include Network Setup and press the button to toggle between On and Off. When set to
Off, the network settings will not be changed.
To export the current DVR settings, connect the USB device to the DVR. If you enabled the NetFS function
(Network menu > NetFS tab), you can upload the setup file on the registered NetFS site. Highlight Setup –
Export… and press the button. Select USB Storage or NetFS. If you select NetFS, select a NetFS site from
the registered NetFS site list. Highlight the box beside File name and press the button. A virtual keyboard
allows you to enter the file name. Selecting Export will save the current settings in .dat file format on the USB device
or the NetFS site.
NOTE:
Even after changing the DVR settings by importing saved settings, the time-related settings (Date/Time,
Time Zone and Daylight Saving Time) will NOT be changed.
CAUTION:
The USB device must be FAT16 or FAT32 format.
Digital Video Recorder
5
Highlight Show System Log… and press the button to display the System Log.
The System Log screen lists system activities (up to 5,000 from the latest) that have occurred along with the time and
date. The
icon will be displayed in the last column for system activities of the remote site. You can scroll through
the log pages by using the Up and Down arrows, or you can go directly to a log page by entering the log page number
in the box at the bottom left of the screen. Highlight Close and press the button to exit the screen.
To export the system log information, connect the USB device to the DVR. If you enabled the NetFS function
(Network menu > NetFS tab), you can upload the log information on the registered NetFS site. Highlight Export…
and press the button. Select USB Storage or NetFS. If you select NetFS, select a NetFS site from the
registered NetFS site list. Highlight the box beside File name and press the button. A virtual keyboard allows
you to enter the file name. Selecting Export will save the log information in .txt file format on the USB device or the
NetFS site.
NOTE:
When opening the saved .txt file, setting to the proper character encoding and using fixed width fonts
will be required to read the file properly.
The box beside Recorded Data – From / To displays the time information of recorded data.
Highlighting Clear All Data… and pressing the button will clear all video data. You will be asked to verify
that you wish to clear all data before the DVR erases the video data. Clear All Data… will not clear the System Log.
Highlight Wizard and press the button. The Wizard setup screen appears. The Wizard setup guides you
through configuring the system for basic operation.
User’s Manual
6
Select either Quick wizard or Network wizard and select the Next button to start the selected setup wizard.
NOTE:
Selecting the Cancel button throughout the screens exits the Quick Setup Wizard without saving your
changes and returns to the main setup screen.
If you selected the Quick wizard, selecting the Next button starts the Quick Setup Wizard.
Digital Video Recorder
7
Date/Time Setup
Date: Set the system date and select the date format.
Time: Set the system time and select the time format.
Time Zone: Select your time zone. The Time Zone can be selected on the map.
Use Daylight Saving Time: Selecting the box sets the system to use daylight saving time.
NOTE:
The Date/Time will be set, and the clock will start when you click the Next button.
Record Method Setup
Select the desired recording mode from:
– Motion Event Record (Recommended)
– Continuous & Motion Event Record
– Continuous Record
NOTE:
You should understand each recording mode before setting the DVR’s recording method.
User’s Manual
8
Record Video Quality Setup
Select the desired video quality profile from:
– Higher Video Quality Priority Profile
– Standard Recording Profile
– Longer Recording Time Priority Profile
NOTE:
The higher quality setting requires more storage space.
NOTE:
The recording quality, recording resolution, and recording speed of each camera channel will be set as
show below according to the Record Method and Record Video Quality you set.
HVQPP*
SRP*
LRTPP*
Motion Event
Record
Very High / Very High / 30 ips
High / Very High / 15 ips
Standard / High / 5 ips
Continuous &
Motion Event
Record
Time, Event: Very High /
Very High / 30 ips
Time: High / Very High / 15 ips
Event: Very High / Very High / 30 ips
Time: Standard / High / 5 ips
Event: High / Very High / 15 ips
Continuous
Record
Very High / Very High / 30 ips
High / Very High / 15 ips
Standard / High / 5 ips
* Record Video Quality: HVQPP (High Video Quality Priority Profile), SRP (Standard Recording Profile), LRTPP (Longer Recording Time
Priority Profile)
Digital Video Recorder
9
Select the Finish button to finish the Quick Setup Wizard and select the Go to Network Setup button to start the Network
Setup.
If you selected the Go to Network Setup, select the Next button to start the Network Setup Wizard.
User’s Manual
10
Internet Connection
Select whether or not your DVR is connected to the Internet.
LAN Setup
Select between Auto Configuration and Manual Configuration for network configuration, and then select the Test
button to test the network configuration you selected.
NOTE:
Selecting Auto Configuration allows the DVR to automatically obtain LAN parameters (IP address, Gateway,
Subnet Mask and DNS Server address). Selecting Manual Configuration allows you to set up LAN
parameters manually.
The network configuration you set should be tested by selecting Test, otherwise the Next button will
cannot be selected, and you cannot move to the next step.
Digital Video Recorder
11
FEN Setup
FEN Name: Enter the DVR name to be registered on the FEN server.
NOTE:
The FEN Name you entered should be checked by selecting Test, otherwise the FEN changes will not
be saved.
When entering no name or a name already registered on the FEN server, an error message displays.
Select the Finish button to finish the Setup Wizard.
Highlight System Shutdown and press the button. The Shutdown screen displays asking you to confirm
whether or not you want to shut the system down.
After selecting Shutdown and pressing the button, a screen will appear telling
you when it is safe to disconnect power.
User’s Manual
12
Date/Time
Figure 5: System – Date/Time setup screen.
Highlight the first box beside Date and press the button. The individual sections of the date will highlight. Use
the Up and Down arrow buttons to change the number. Use the Left and Right arrow buttons to move between month,
date and year. Once you have the correct date, press the button.
Highlight the Format box beside Date and press the button. Select from the three available date formats and
press the button to save your selected format.
Highlight the first box beside Time and press the button. The individual sections of the time will highlight.
Use the Up and Down arrow buttons to change the number. Use the Left and Right arrow buttons to move between
hour, minutes and seconds. Once you have the correct time, press the button.
Highlight the Format box beside Time and press the button. Select from the three available time formats and
press the button to save your selected format.
NOTE:
The clock will not start running until you have highlighted Save and pressed the button.
Highlight the box beside Time Zone and press the button. Select your time zone from the list and press the
button.
NOTE:
The Time Zone can also be selected on the map below by pressing the Left and Right buttons or scrolling
the mouse wheel up and down.
Highlight Use Daylight Saving Time and press the button. Pressing the button toggles between On and
Off.
Highlighting Time Sync.… and pressing the button displays the Time Sync. screen. You can set up time
synchronization between the DVR and standard time servers that are available in most time zones and countries, or
between the DVR and another DVR.
/
