MIMAKI UJF-706 Operating instructions

Brand: MIMAKI

Model: UJF-706

Category: Print & Scan

Type: Operating instructions

MIMAKI UJF-706 is an optional roll unit that allows for stable feeding of roll media. It enables continuous printing on roll media and supports the use of 100mm-thick media with the roll unit function turned off. Additionally, the unit features an ionizing bar for static electricity removal.

D202150-12

OPTIONAL ROLL UNIT

MIMAKI ENGINEERING CO., LTD.

1-ii

CAUTION ........................................................................ vi

CAUTION ........................................................................vi

Requests .........................................................................vi

FCC Statement (USA) .....................................................vi

Interference to televisions and radios ..............................vi

CDRH REGULATION .....................................................vii

Foreword ........................................................................viii

For safe operation ........................................................... ix

Symbols ...........................................................................ix

Position of the warning label ............................................ xi

CHAPTER 1 Before Use

Configuration and Function ...........................................1-2

Front Side (Take-up device) ......................................... 1-2

Rear Side (Feeding device) ..........................................1-3

Operation Switch .......................................................... 1-4

CHAPTER 2 How to Use

Setting the media ...........................................................2-2

Operation before drawing ............................................2-10

Drawing data ...............................................................2-11

Feeding and cutting media (after drawing) ..................2-12

Hint on usage of this unit .............................................2-14

Cleaning the table ...................................................... 2-14

Head maintenance .....................................................2-14

Precautions when using various types of media ........ 2-14

How to close the absorbing holes on the table ........... 2-14

How to use the weight ................................................ 2-15

How to use the UV lamp ............................................. 2-16

How to use the mist fan .............................................. 2-17

How to use roll media 1 print ...................................... 2-18

CHAPTER 3 Maintenance

Ionizing bar ....................................................................3-2

TABLE OF CONTENTS

1-iii

CHAPTER 4 Troubleshooting

Troubleshooting ............................................................ 4-2

Media cockles (While printing) ......................................4-2

Media cockles (While feeding) ......................................4-2

Media skews .................................................................4-4

Troubles that messages are displayed ......................... 4-5

Error message ..............................................................4-5

CHAPTER 5 Appendix

Specifications ................................................................ 5-2

1-iv

1-v

CAUTION

THIS LIMITED WARRANTY OF MIMAKI SHALL BE THE SOLE AND EXCLUSIVE WARRANTY AND IS IN LIEU

OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING , BUT NOT LIMITED TO, ANY IMPLIED

WARRANTY OF MERCHANTABILITY OR FITNESS, AND MIMAKI NEITHER ASSUMES NOR AUTHORIZES

DEALER TO ASSUME FOR IT ANY OTHER OBLIGATION OR LIABILITY OR MAKE ANY OTHER WARRANTY

OR MAKE ANY OTHER WARRANTY IN CONNECTION WITH ANY PRODUCT WITHOUT MIMAKI’S PRIOR

WRITTEN CONSENT.

IN NO EVENT SHALL MIMAKI BE LIABLE FOR SPECIAL, INCIDNETAL OR CONSEQUENTIAL DAMAGES OR

FOR LOSS OF PROFITS OF DEALER OR CUSTOMERS OF ANY PRODUCT.

Requests

• This Operation Manual has been carefully prepared for your easy understanding, however, please do not hesitate

to contact a distributor in your district or our office if you have any inquiry.

• Description contained in this Operation Manual are subject to change without notice for improvement.

FCC Statement (USA)

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the operation manual, may cause

harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which cause the user

will be required to correct the interference at his own expense.

Interference to televisions and radios

The product described in this manual generates low radio waves while it is in operation. The product can interfere

with radios and televisions if set up or commissioned under improper conditions. The product is not guaranteed

against any damage to specific-purpose radios and televisions.

The product’s interference with your radio or television will be checked by turning on/off the power switch of the

product.

In the event that the product is the cause of interference, try to eliminate it by taking one of the following

corrective measures or taking some of them in combination.

• Change the direction of the receiving antenna or the feeder of your radio/television.

• Move the receiver away from the product.

• Plug the power cord of this machine into an outlet which is isolated from power circuits connected to the television

set or radio.

• In the case where MIMAKI-recommended cable is not used for connection of this device, limits provided

by FCC rules can be exceeded. To prevent this, use of MIMAKI-recommended cable is essential for the

connection of this device.

vii

CAUTION

CDRH REGULATION

The Center for Devices and Radiological Health for the U.S. Food and Drug Administration Implement

regulations for laser products. The sentence of “This product complies with 21 CFR chapter I and subchapter J”

indicates compliance with the CDRH regulations and is labeled on the product when marketed in the United

States. This Model is equivalent to Class II laser device according to CDRH Regulation.

This product complies with 21 CFR chapter I and subchapter J

• Use of controls, adjustments or performance of procedures other than those specified in this manual

may results in hazardous radiation exposure.

viii

Foreword

Congratulations on your purchase of UJF-706 optional roll unit.

UJF-706 optional roll unit is an unit for feeding roll media stably.

Page feeding function allows the unit to print continuously on a roll media.

In addition, by making the roll unit function OFF, you can print the 100mm-thick media.

(When the option roll unit is not attached, you can print the 150mm-thick media.)

This Operation Manual describes media setting or others when the roll unit is set and used on UJF-706.

For printing and various settings of UJF-706, refer to the Operation Manual of UJF-706.

You can also download the latest operation manual from our website.

Reproduction of this manual is strictly prohibited.

For safe operation

Symbols

Symbols are used in this Operation Manual for safe operation and for prevention of damages to the machine.

The indicated sign is different depending on the content of caution.

Symbols and their meanings are given below. Please follow these instructions as you read.

Examples of symbols

Failure to observe the instructions given with this symbol can result in death or serious injuries to

personnel. Be sure to read it carefully and use it properly.

Failure to observe the instructions given with this symbol can result in injuries to personnel or

damage to property.

Important notes in use of this machine are given with this symbol. Understand the notes

thoroughly to operate the machine properly.

Useful information is given with this symbol. Refer to the information to operate the machine

properly.

Indicates the reference page for related contents.

The symbol “ “ indicates that the instructions must be observed as strictly as the CAUTION

instructions (including DANGER and WARNING instructions). A sign representing a precaution

(the sign shown at left warns of hazardous voltage) is shown in the triangle.

The symbol “ " indicates that the action shown is prohibited. A sign representing a prohibited

action (the sign shown at left prohibits disassembly) is shown in or around the circle.

The symbol “ " indicates that the action shown must be taken without fail or the instructions

must be observed without fail. A sign representing a particular instruction (the sign shown at left

instructs to unplug the cable from the wall outlet) is shown in the circle.

For safe operation

Precautions for installation

CAUTION

A place exposed to direct

sunlight

A place that is not horizontal

A place where temperature and

humidity varies significantly

•Use the machine under the

following environment.

•Operating environment :

15 ～ 30 ℃ (59 ～ 86 F)

35 ～ 65 % (Rh)

A place that vibrates

A place exposed to direct air

blow from air conditioner, etc.

Around a place where fire is used

Position of the warning label

Warning labels are adhered on this machine. Be sure to fully understand the warnings given on the labels.

In the case where any of the warning label has become so soiled that the warning message is illegible or has

come off, purchase a new one from your local distributor or our office.

Vacuum Unit

(mounted on the unit)

(2 places each on the front and back)

(2 places each on

the front and back)

xii

Position of the warning label

Order No. Label

(1) M907071

(2) M907072

(3) M906115

(4) M906222

This chapter describes the parts name and functions.

Configuration and Function .................................1-2

Front Side (Take-up device) ...................................... 1-2

Rear Side (Feeding device) ....................................... 1-3

Operation Switch ....................................................... 1-4

CHAPTER 1

Before Use

1-2

Configuration and Function

Front Side (Take-up device)

Return roller (x 3), Roll protection cover

Set media to the take-up device with the rollers.

Put tension on the media to take up media.

Tension bar lifting stopper

Stops lifting of the tension bar.

Roll holder

Takes up the roll media.

Vacuum unit

Vacuums roll media.

(mounted on the unit)

Operation switch ( P.1-4)

Feeds the media or fixes the roll

holder.

Tension bar stopper

Locks the tension bar.

Vacuum unit controller

Controls the vacuum unit on either the right or

left of the printer.

1-3

Configuration and Function

Before Use

Rear Side (Feeding device)

Operation switch (

P. 1- 4

)

Feeds the media or fixes the roll holder.

Tension bar stopper

Locks the tension bar.

Return roller (x 1)

Set media to the printer with this roller.

Roll holder

Takes up the roll media.

Configuration and Function

1-4

Operation Switch

ROTATING DIRECTION switch

Normally (drawing on the obverse side) flip

it down on the take-up side, and up on the

feeding side.

When drawing on the reverse side, set each

switch in the opposite position.

MANUAL / AUTO switch

Set AUTO to set media, and set MANUAL

to feed media after drawing.

Rotation lock lever

Lock or release the rotation of the

roll holder.

Pull it up to release the lock.

Holder lock lever

Flip it down to lock the roll holder.

This chapter describes the procedure from setting media to draw-

ing, and usage hint of this unit.

Setting the media ...................................................2-2

Operation before drawing ...................................2-10

Drawing data ........................................................2-11

Feeding and cutting media (after drawing) .......2-12

Hint on usage of this unit ...................................2-14

Cleaning the table .................................................... 2-14

Head maintenance .................................................. 2-14

Precautions when using various types of media ..... 2-14

How to close the absorbing holes on the table ........ 2-14

How to use the weight ............................................. 2-15

How to use the UV lamp .......................................... 2-16

How to use the mist fan ........................................... 2-17

How to use roll media 1 print ................................... 2-18

CHAPTER 2

How to Use

2-2

Setting the media

Set a paper core to the take-up device, and then

mount the roll holders on both sides.

(1) Set a paper core to the left roll holder, and then slide the

right roll holder to the left to set to the paper core.

(2) Tighten screws on both sides to fix the holders.

Set a media to the feeding device, and then mount

the roll holders on both sides.

(1) Set a media to the left roll holder, and then slide the right roll

holder to the left to set to the media.

(2) Tighten screws on both sides to fix the holders.

• Insert the paper core all the way seated in the roll holder on

both sides. A loosened core may spin around during

working.

• Insert the media all the way seated in the roll holder on both

sides. A loosened media may spin around during working.

• Set a media “facing inward” (see the figure below).

• Center the media on the table.

• Setting direction of the media depends on the side to be drawn, obverse or reverse.

(2)

(1)

(2)

(1)

Media

Table

Tension bar

Take-up side Feeding side

Media

Table

Tension bar

Take-up side

Feeding side

Facing inward

(drawing on the obverse)

Facing outward

(drawing on the reverse)

Recommended

For reference

Take-up side Feeding side

ROTATING

DIRECTION

ROTATING

DIRECTION

MANUAL

AUTO

MANUAL

AUTO

Take-up side Feeding side

MANUAL

AUTO

ROTATING

DIRECTION

ROTATING

DIRECTION

MANUAL

AUTO

• When media is set facing outward, one time lock on the

feeding side is disabled. ( P.2-6)

Instead, the rotation lock lever and the holder lock lever of

the roll holder are enabled as a brief function. ( P.1-4)

2-3

Setting the media

How to Use

Set the operation switch as shown on the right.

• Normally (drawing on the obverse side) set as shown on the

right.

When drawing on the reverse side, set each switch in the

opposite position.

(Both of the take-up side and the feeding side)

Release the tension bar stopper and then move the

tension bar to its evacuation position.

(1) Push the tension bar stopper to the right to release, and

then raise the tension bar.

(2) Pull the tension bar stopper to the left to lock and fix the

tension bar.

Press the key of the operation panel to move the table to the back, and then

press the key to turn it off.

(Feeding side) Raise the outside shaft of the two-shaft at the rear edge of the table.

(1) Move the lever A at both edges of the shaft outside to

unlock the shaft.

(2) Raise the shaft.

Take-up side

Feeding side

(1)

(2)

VACUUM

Lever A

Raise the outside

thicker shaft.

2-4

(Feeding side) Pull the rotation lock up on the right

of the operation switch.

• The lock of the roll holder is released.

(Feeding side) Pull out the media and pass it

through the two-shaft. Then, paste the top edge of

the media on the table edge with tape.

(Feeding side) Move the shaft that you raised in the

Step 6 downward, and tuck the media into it.

• When you move the shaft downward, the hooks at right and

left of the shaft are inserted into with a clicking sound. If they

are not inserted fully, press them from above.

Page is loading ...

MIMAKI UJF-706 Operating instructions

MIMAKI UJF-706 Operating instructions

MIMAKI UJF-706 Operating instructions

Related papers

Other documents