6-IN-1 NON-INVASIVE MOISTURE METER
KC-316A
USER’S MANUAL
1
CONTENTS
Introduction.............................................................................................1
Product Overview...................................................................................1
LCD Screen Overview............................................................................2
Operating instructions..........................................................................2-3
Operation Tips.........................................................................................3
Safety Instruction....................................................................................3
Battery Safety Tips................................................................................3-4
Specifications..........................................................................................4
Warranty...................................................................................................5
INTRODUCTION
The KC-316A moisture measuring instrument is designed with a non-invasive principle, utilizing the
sensing part of the instrument head. It allows for accurate moisture measurement of various materials
without damaging the object being tested. Through the instrument's LCD screen, users can easily obtain
the moisture content, ambient temperature, humidity, and mildew index of the tested object under the
current environment. The product is compact, easy to operate, provides rapid measurement, and is
highly portable. It is an essential tool for on-the-go use.
PRODUCT OVERVIEW
A. Inductive measuring components
B. LCD
C.Function Button
D. Battery compartment
E. Battery compartment cover
2
LCD SCREEN OVERVIEW
A. Buzzer function identifier
B. Battery indicator
C. Moisture level display
D. Mildew index display
E. Moisture value display
F. Locking sign
G. Measurement mode display
H. Ambient temperature value
I. Temperature unit
J. Ambient humidity
OPERATING INSTRUCTIONS
INSTALL BATTERIES
To open the battery compartment at the bottom of the tool.Then insert 2pcs AAA batteries into the
compartment according to the positive and negative electrode marks.
SELECTING THE MODE
1.Long Press the POWER button to turn on the tool with a beep.The default startup mode is DRYWALL
2.Press the MODE button to switch between the DRYWALL;CEMENT BOARD;SOFT WOOD and HARD
WOOD mode.
3.Press and hold the power button for about 1s and then shut down
MEASUREMENT
1. Place the sensing parts of the machine in close contact with the flat surface of the object being
measured(like below schematic diagram). Wait until the moisture value stabilizes before reading the
measurement result. If the moisture content exceeds the measurement range, "HH%" will be displayed
on the screen.
3
2. Briefly press the "HOLD" key during measurement to lock the moisture measurement data.
3. The lower section of the screen displays the current environmental temperature and humidity in
real-time. The device also calculates the mildew index (nine levels in total) based on the current
environmental conditions and displays it in the "D" area of the screen.
4. Briefly press the "SET" key to turn the buzzer on or off. This function has a power-off memory feature.
When the buzzer is on, an alarm will sound when the moisture value exceeds the red range.
5. Press and hold the "SET" button to switch the temperature display unit. This function also has a
power-off memory feature.
6. After 15 seconds of inactivity, the backlight will dim, and the device will enter power-saving mode. It
will exit power-saving mode when there is key operation or when the moisture value changes by more
than 1%.
STATUS INDICATION
Moisture indicator:
1. Gypsum board mode:
● Green indicator block - 1%~16%:DRY
● Yellow indicator block - 16.1%~28%:SLIGHTLY DAMP
● Red indicator block - 28.1%~50%:EXCESSIVE DAMPNESS
2. Cement board mode:
● Green indicator block - 1%~16%:DRY
● Yellow indicator block - 16.1%~28%:SLIGHTLY DAMP
● Red indicator block - 28.1%~50%:EXCESSIVE DAMPNESS
3. Cork mode:
● Green indicator block - 1%~16%:DRY
● Yellow indicator block - 16.1%~28%:SLIGHTLY DAMP
● Red indicator block - 28.1%~50%:EXCESSIVE DAMPNESS
4. Hardwood mode:
● Green indicator block - 1%~16%:DRY
● Yellow indicator block - 16.1%~28%:SLIGHTLY DAMP
● Red indicator block - 28.1%~50%:EXCESSIVE DAMPNESS
5. Mildew index indicator bar:
The mildew index is 9 levels in total, and the higher the index is, the easier the mildew will occur;
CALIBRATION INSTRUCTION
This instrument features a self-calibration function. If the hand-held instrument is used in the air (with no
other object within a 50 cm radius of the machine), the displayed moisture data may not be 0. To perform
a self-calibration, press and hold the "HOLD" button for 3 seconds until the "CAL" symbol appears on the
display screen. The instrument will enter automatic calibration mode, remain stable, and wait for the
moisture data to be displayed again. Once the calibration is complete, the instrument will display the new,
accurate moisture measurement.
OPERATION TIPS
1. In case the instrument fails to start normally or displays a low battery symbol on the LCD screen after
4
turning on, it indicates that the battery needs replacement. Please replace the battery before use.
2. The moisture value of the measured wood is influenced by ambient humidity and wood density. To
ensure accurate measurements, it is crucial to select the correct measurement mode. The moisture
trend of the material should be assessed by analyzing data obtained from multiple measurements.
SAFETY INSTRUCTION
The following safety tips must be observed when using this product to avoid physical injury.
● Please read all contents of this manual carefully before correct operation.
● Do not remove any label on the instrument.
● Do not operate the instrument with flammable and explosive gases.
● Children are not allowed to use this instrument.
BATTERY SAFETY TIPS
● Prior to cleaning this product, remove the battery.
● If the product will not be in use for an extended period, please remove the battery.
● Ensure proper battery installation by aligning the positive and negative poles accordingly.
● Please dispose of used batteries in accordance with regulations: avoid exposing batteries to high
temperatures or disposing of them in fire. Insulate the battery terminals with tape to prevent contact with
other objects. Many countries have specific guidelines regarding battery disposal, kindly comply with
relevant regulations.
SPECIFICATIONS
Measuring range
DRYWALL
CENMENTBOARD
0 ~ 50% Relative value
SOFTWOOD
HARDWOOD
0 ~ 50% ±2%
Temperature/humidity
measurement
Temperature
-9.9 ~ 50℃ :±1℃ (14~122℉: ±1.8℉)
Humidity
0 ~ 99.9%RH ±3%
No operation backlight darkening time
About 15 seconds
Automatic shutdown
No operation for 2 minutes
C A U T I O N S
● Do not tear off any labels on the instrument
● Do not drop and use rough
● Do not disassemble or install the machine (to avoid causing malfunction)
● Do not place with corrosive gases or other corrosive substances
● Do not use in rain and water droplets
● Do not expose this product to vibrations or high and low temperatures
● Please keep the machine dry and clean.
● Do not immerse the machine in water to avoid damage to the product
● Please remove the battery when the product is not used for a long time
5
Power supply
2*AAA
Maximum power consumption
<70mA
Operating ambient temperature
0～50℃ (32～122℉)
Working environment humidity
<90%RH No condensation
Storage environment
-20～60℃(-4～140℉)，≤85%（Without battery）
Dimensions
197mm*61mm*54mm
Weigh
About 136g（Without battery）
● Thank you for purchasing our products.
● This instrument is not a universal instrument that can detect any material in the wall, I hope users can
understand it.
● Please read this manual carefully before operating it correctly.
● Please keep it properly after use.
WARRANTY
This product is covered by a one-year warranty from the date of purchase, guaranteeing that it is free
from defects in materials and workmanship.
Please note that the warranty does not apply under the following conditions:
Any disassembly of internal machine will void the warranty.
Any damage resulting from abrasion, water, dropping, or disassembling is not covered by the
warranty.
Tip: As many components of this product are recyclable, please dispose of it according to local laws
instead of throwing it in the trash.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Protimeter MMS3 INS9800 Amphenol Advanced Sensors User manual
-
General Tools MM8 User manual
-
General MM8 User manual
-
General Tools & Instruments MMD7NP Operating instructions
-
-
Omega RH650 Owner's manual
-
-
Balance Living Precision LIFE TRACK 10500 User manual
-
EDAN iM50 User manual
-
Yellow Jacket Combustion Analyzer CA502 User manual
