HOOK Reveal 9

Lowrance HOOK Reveal 9, HOOK² 9 Template

  • Hello, I've examined the provided mounting template document for the Lowrance Hook² 9 and Hook Reveal 9. This template provides precise dimensions for mounting your device and includes important details such as pilot hole sizes for different materials and product outlines. I'm ready to answer your questions about this document.
  • Can I use this template if it's a copy?
    What should I check before using the template?
    What are the recommended pilot hole sizes for soft materials?
    What are the recommended pilot hole sizes for hard materials?
REMOVE SHADED AREA
Ø25.4 mm (1.00”)
SUN COVER
PRODUCT OUTLINE
67.3 mm (2.65”)
84.1 mm (3.31”)
81.1 mm (3.19”)
282.9 mm (11.14”)
251.5 mm (9.90”)
277.3 mm (10.92”)
168.2 mm (6.62”)
134.5 mm (5.30”)
162.3 mm (6.39”)
67.3 mm (2.65”)
84.1 mm (3.31”)
81.1 mm (3.19”)
L
C
L
C
Material
Soft materials e.g. Plywood
Hard materials e.g. Fiberglass, Acrylic, Hardwoods
Recommended pilot holes
#6 screw
Ø 2.3-2.5 mm (3/32”)
Ø 2.7-3.1 mm (7/64”)
218.0 mm (8.58”)
152.0 mm (5.98”)
141.4 mm (5.57”)
138.7 mm (5.46”)
125.8 mm (4.95”)
109.0 mm (4.29”)
141.4 mm (5.57”)
138.7 mm (5.46”)
125.8 mm (4.95”)
109.0 mm (4.29”)
76.0 mm (2.99”)76.0 mm (2.99”) 76.0 mm (2.99”)
Hook
2
9/ Hook Reveal 9
Mounting Template
NOTE:
DO NOT SCALE
PRINT 1:1
*988-11782-002*
IMPORTANT. Do not use this template if it has been rescaled by copying or

dimension lines below are to scale before use.







su uso.






















注意:请尽量不要使用本安装挖孔尺寸模版图的复印件。如果使用复印件
,则在使用之前请确认其比例一定要与原件大小必须一致。
중요: 복사나 출력으로 크기가 조정 된 경우 이 템플릿을 사용하지
마십시오. 원본이 아니거나 인쇄물이면, 사용하기 전 아래 치수선의
눈금을 확인 해 주십시오.
注:このテンプレ トは印刷やコピ によって縮尺がわっていること
がありますので使用しないで下さい。テンプレ トがオリジナルのもの
でない場合には、下の寸法線を使って縮尺を確認してください。
ВНИМАНИЕ: Не используйте эту инструкцию, если она была
изменена в размерах при копировании или распечатке. Если
вы используете не оригинал, а распечатку из файла, убедите
сь в соответствии размеров линейки в нижней части инстру
кции с действительными размерами.
Check dimensions before cutting
12"
300 mm
82.7 mm
(3.26“)
28.9 mm
(1.14“)
Maximum curve of the dash
1 mm (0.04”)
/