Elecder D18 User manual

Brand: Elecder

Model: D18

Type: User manual

Elecder D18: Wireless earbuds with Bluetooth V5.0, offering a stable connection and clear sound quality. With a battery capacity of 40mAh for each earbud and 500mAh for the charging case, you can enjoy up to 5-6 hours of playtime and 4-5 hours of talk time on a single charge. The earbuds also feature multi-functions like pause/play, volume control, and answering/ending calls with just a tap.

Bluetooth version V5.0

Operation distance 10 m

Audio coding format SBC,AAC,APTX

BT profiles support HSP, HFP, A2DP, AVRCP

Battery capactity 40mAh for each earbuds

500mAh for charging case

Charging time Around 2 hours

Playing time 5-6 hours

Talk time 4-5 hours

Standby time Around 70 hours

Frequency range 20-20kHz

Driver unit 6mm

Earbuds weight 5g each

Earbuds

22*40mm

Elecder D18

Wireless Earbuds

Power ON/OFF Pairing

Stereo Mode:

Mono Mode:

Elecder D18

Multi Functions

Elecder D18

Pause/Play Single tap L/R

Double tap L

Previous Song

Active Siri/Googel

Assitant Triple tap L or R

Refuse the call

Answer/End a call Tap L or R

Long touch L or R

The correct way of wearing

Put earbuds in the ear and gently rotate until 45° above

(as shown below).

Thank you for purchasing your new Elecder D18 true

wireless earbuds.

We recommend that you spend some time reading this

instruction manual in order that you fully understand all

the operational features it offers.

Read all the safety instructions carefully before use and

keep this instruction manual for future reference.

1. Charge the earbuds and the charging case at least once

every 6 months.

2. Do not store the product in extreme temperature

(below 0 or above 45 ).

3. Do not use chemicals or detergents to clean the product.

4. Do not drop or knock the product on hard surfaces.

5. Do not scrape the surface of product with sharp objects.

6. Do not try to take the product apart.

Power ON:

When you open the charging case(with battery

power inside), it will be power ON automatically

and blue LED will blink.

When the earbuds L & R is power OFF after taking

out of the charging case, long touch the L & R earbuds

button to turn it on and blue LED will blink.

Power OFF:

When you put the L & R earbuds into the charging

case(with battery power inside), close the charging

case, it will be power OFF automatically.

When the earbuds L & R is power ON after taking out

of the charging case, long touch the L or R earbuds

button to turn it off under BT disconnection status.

Note: Under BT disconnection status more than 5 mins,

the L & R earbuds will be power OFF automatically.

2. Activate Bluetooth on the phone and search for

“Elecder D18” to connect. Blue LED will blink

slowly after connected.

1. Take out both earbuds from the charging case,

the L&R earbuds will be automatically connected.

Blue LED will blink.

1. Take out L or R earbuds from the charging case.

Blue LED will blink.

2. Activate Bluetooth on the phone and search for

“Elecder D18” for L earbuds Or

“Elecder D18 R” for R earbuds.

Blue LED will blink slowly after connected.

Note: In Mono mode, double tap L or R can only

move to next song.

Charging Mode

* Charging: Red LED is on

* Full charged: Blue LED is on & turned off after

about 30s

2. Charging the case by Type-C cable

1. Charging the earbuds

Take earbuds into charge case

* Charging: < 30% battery, Red LED is on

30%-80% battery, Orange LED is on

80%-100% battery, Green LED is on

Safety Rules

Specifications Product Overview

How to Wear?

Type-C

ENGLISH ENGLISH ENGLISH ENGLISH ENGLISH

Multi-Function

Button(MFB) LED

Indicator

Soft Silicon

Earbud

Charging

Point

Microphone

Charging

Point

Charging

Case LED

Next Song Double tap R

Volume Down Long touch L for 2s

Volume Up Long touch R for 2s

In case there is no auto pairing after taking out the

earbuds from the charging case, please follow the

below steps to restore the default setting:

1. Ensure L&R disconnect to any device(trun off

the bluetooth device connected before).

2. Trun off both L&R earpbuds.

3. Long touch MFB button of L&R earbuds around 8s

till both red light flash 3 times. The factory reset is

now finished.

4. The L&R earbuds will be automatically connected

and blue LED will blink. The earbuds is ready to pair

with your device now.

Factory reset

Bluetooth Transmission

Frequency Range: 2402MHz-2480MHz

Max. Transmission

Power (Bluetooth) 8dBm

MADE IN CHINA

3. Charge the case by wireless charger

1. Keep the earbuds away from high temperature

and humidity

2. Do not put the earbuds directly in the sun to burst,

or put it in a high temperature environment, which

will shorten the life of the earbuds (internal department

of electronic components and batteries).

3. Do not try to disassemble the earbuds body.

4. Do not drop the earbuds on a hard surface.

5. Do not use sharp objects to scratch the surface of

the product.

6. Do not use chemicals or detergents to clean the earbuds.

http://www.elecder.net

EARBUDS MANTENANCE:

WARRANTY REGULATIONS:

WARRANTY AND AFTER SALES:

The following conditions are not covered by the warrenty:

1. Because of buying second-hand or used products.

2. Damage caused by irregular operation.

3. Damage caused by natural disasters.

4. Damage caused by chemical substances, open flames,

radioactive substances, toxic substances, liquids.

5. Damage caused by third parties / people / things or others.

If you need after-sales or any help, please contact us

by the email "[email protected]", our customer

service will reply you within 24 hours, we will do our

best to solve your problem.

For more information please visit http://www.elecder.net

* Full charged: Green LED is off

Note: 5V/1A or 5V/1.5A is the best choice

for the charger.

NOTE: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help

Changes or modifications not expressly approved by the party responsible for compliance

could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may

cause undesired operation.

Elecder D18 User manual

Elecder D18 User manual

Other documents