Honda Civic Si Coupe Owner's manual

Category
Car navigation systems
Type
Owner's manual
2019
NAVIGATION MANUAL
The information and specifications included in this publication were in effect at the time of approval for printing. Honda Motor Co., Ltd., reserves the right,
however, to discontinue or change specifications or design at any time without notice and without incurring any obligation.
Accessories Precautions
The GPS antenna is located in the dashboard.
Metallic front
or side window tinting can seriously degrade or obstruct GPS reception.
Signal noise from devices such as radar detectors, vehicle tracking de
vices, remote starters, and additional amplifiers can disrupt the navigation system. If you
install any such item, install it away from the navigation display and antenna.
Important Safety Information
Avoid focusing on the screen or manually operating the system controls while driving.
Certain on-screen controls are disabled when driving, however most of t
he voice comm
ands continue to function. Pull to the side of the road if you need to devote
more attention and time to look at the screen or access additional menus.
Route guidance may conflict with street closures, road construction, detour
s, and out-of-date map data.
The system itself may also have limitations. Verify route information by carefully observing roads, signs, and signals. Always use your own judgment and
obey
traffic laws.
2
System Limitations P. 128
NOTICE
This vehicle’s navigation display, if so equipped, includes mercury-containing components. Upon removal, please reuse, recycle, or dispose of as hazardous waste.
Clean the screen with a soft, damp cloth. You may use a mild cleaner intended for use on navigation screens.
3 WARNING
Using the navigation system while driving can take your
attention away from the road, causing a crash in which you
could be seriously injured or killed.
Only operate system controls when the conditions permit you
to safely do so.
00X31-TBA-8300 2019 Civic Navigation Manual NM-08627
Contents
2 System Setup P. 15
Start-up 16 Voice Control System 17 Personal Information 18 Display Mode Settings 26
Map & Vehicle 28 Navigation 36 Traffic 44 Other Settings 45
Data Reset 51
2 Navigation P. 53
Entering a Destination 54 Calculating the Route 74 Driving to Your Destination 77 Map Operation 81
Changing Your Route 91 Changing Your Destination 94
2 Other Features P. 107
About Apps Menu 108 ecoRoute
TM
109 Information Functions 117
2 Troubleshooting P. 121
Troubleshooting 122
2 Reference Information P. 127
System Limitations 128 Customer Assistance 130 Legal Information 132
2 Voice Commands P. 135
Voice Commands 136 List of Categories 138
Quick Reference Guide
P. 2
System Setup
P. 15
Navigation
P. 53
Other Features
P. 107
Troubleshooting
P. 121
Reference Information
P. 127
Voice Commands
P. 135
Index
P. 139
2
Quick Reference Guide
Quick Reference Guide
Overview—Functions at a Glance
Navigation
You can select any place/landmark as a destination by using the touchscreen. The navigation system gives you
turn-by-turn driving directions to your destination.
Store home address
(P18 )
Register
1
home address.
Track route
(P77 )
Follow your route in real-time with voice guidance.
Store contacts
(P19 )
Store locations to use as the destination.
Enter destination
(P54 )
Select your destination using several methods.
Select route
(P75 )
Set route preferences and select one of the available routes.
Avoid certain areas
(P39 )
Set streets and areas to detour around.
Add waypoints
(P93 )
Add “pit stops” along your route.
Traffic Information* (P86)
View and avoid congestion and traffic incidents.
*: Available only in certain areas.
3
Quick Reference Guide
HOME Screen
The system displays various functions from the HOME screen. Press the button at any time to return to the main HOME screen.
Navigation Top Screen
Display the map screen and operate the navigation features. From the HOME screen, press the button and then press the button. The
navigation top screen is displayed.
(Home)
Display the HOME screen.
(Map)
Display the map screen.
(Back)
Go back to the previous screen.
VOL (Volume)
Increase or decrease the audio volume.
Display the map menu.
Navigation
Display the navigation feature that
was used the last time.
At start-up, the navigation top
screen is displayed.
(Display Mode)
Switch between Day and Night modes
manually.
GPS signal strength (P120)
Display the satellites’ status.
Where To? (P54)
Select search methods to enter a destination for
route guidance.
Apps (P108)
Display the useful functions incorporated into the
navigation system.
View Map (P6 )
Display the map screen.
Settings (P15 )
Change the settings for the navigation
functions.
4
Quick Reference Guide
Touchscreen Operation
You can operate the system using your finger on the touchscreen.
The touchscreen can be operated if you are wearing thin gloves, but it may be more diff
icult for the system to respond.
Tap
Touch the screen lightly with your finger to select an option on the
screen.
Swipe
Lightly sweep your finger side to side or up and down to scroll a list
or map.
You can change the touchscreen sensitivity setting.
2 Refer to the O
wners Manual.
Slide
Move your finger slowly across the screen to scroll the map.
Pinch In/Out
Open or close your fingers on the screen in a pinching motion to
zoom in or out of the map.
5
Quick Reference Guide
How to Enter Information
You can enter information (e.g., city names, street names, numbers, and symbols) when prompted on the input screen.
Using Voice Commands
When you see in this manual, voice commands are available for
that feature.
The system recognizes only certain commands.Available navigation
vo
ice commands (P136)
Press the button, and say the letter, nu
mber, or symbol (e.g.,
say 1”).
If a voice command is not recognized, a list is displayed with
possible options.
On list screens:
Say the number of the list item (e.g., say Three” to select
item 3).
Say Ma
in menu” to return to the voice command menu
screen.
Say Back
to return to the previous screen.
Say Page U
p” to scroll up one page.
Say Page D
own” to scroll down one page.
Say Exit” to
end the voice command function.
Using the Touchscreen
Select a character or icon on the screen to select it.
Select to remove the last entered character.
Select to remove all entered characters.
Select to display upper/lower case characters.
Select to enter a space character.
Select to display other types of characters.
Select to change the keypad language.
On input search screens, the suggested search terms are
displayed. Select to display a list of possible entries.
6
Quick Reference Guide
Map Screen Legend
The color of the map is different depending on the selected Map Theme.
Map operation icons
(P81 )
Map menu (P82)
Map scale (P81)
Current vehicle position
Streets
Landmark icons
Traffic incident icons
Traffic flow indicator
Traffic is flowing
normally.
Traffic is slightly
congested.
Traffic is heavily
congested or stopped.
Searching specific category (P73)
Traffic has not
updated.
Map buttons (P33 )
Feature areas
7
Quick Reference Guide
During Route Guidance
During route guidance, route information is displayed on the map screen.
You can see the detailed information on the turn information s
creen.
Map Screen
Guidance Screen
Day or Night Mode
Press the button to manually
switch between Day and Night modes.
Turn-by-Turn Directions
The next guidance point appears on
the Driver Information Interface (DII).
Day Mode Night Mode
Remaining
distance
Street name of next
guidance point
Next driving maneuver is
approaching.
8
Quick Reference Guide
Navigation—Home Addresses and Going Home
The “Home” feature automatically routes you to your home address from any location simply by selecting Go Home.
You can store one home address. (P18 )
The order of the steps may change depending on the map data loaded on your system.
Storing Your Home Address
a Press the button.
b Select .
c Select and then select Set
Home Location.
d Select Enter My Address.
e Select Search All.
f Enter a house number and then select
Done.
g Enter a street and then select Done.
h Select a street from the list.
If the select city screen is displayed,
select a c
ity.
i Select an address from the list.
j Select Select.
Going Home
a Press the button.
b Select .
c Select Go Home.
Alternatively, you can say
Na
vigation” and then Go
Home” fro
m any screen.
9
Quick Reference Guide
Navigation—Entering a Destination
Enter your destination using one of several methods, then follow route guidance on the map to your destination.
The order of the steps may change depending on the map data loaded on your system.
a Press the button.
b Select .
c Select Address.
d Select Search All.
e Enter the house number and select
Done if necessary.
f Enter the name of your destination
street and select Done.
g Select your destination street from
the list.
If the select city screen is displayed,
select a city.
h Select an address from the list.
i Select Go!.
Route guidance to the destination
beg
ins.
Routes: Choose one of multiple routes.
: Display your destination map and
save a plac
e.
10
Quick Reference Guide
Navigation—Changing Route or Destination
You can alter your route by adding waypoints to visit, or changing your destination during route guidance.
Adding a Waypoint (“Pit Stop”)
You can add waypoints along your route.
(P93 )
a Press the button.
b Select .
c Select a search method.
d Select the location to add to the
destination list and select Go!.
e Select Add to Active Route.
f If necessary, edit the order of the
destinations and select Done.
Changing Your Destination
There are several methods you can use to
specify a new destination during route
guidance.
Searching nearby hospitals, police
stations, or ga
s stations (P95 )
Select the vehicle icon and select an
op
tion.
Selecting an icon on the map (P94 )
Select a place/landmark icon or a new
area o
n the map twice.
Entering a new destination (P97 )
Select Wh
ere To? and then enter a new
destination.
Canceling Your Route
a Select .
Alternatively, you can say
Na
vigation” and then Stop
route” from
any screen.
Help
This navigation system comes with help
information, which tells you how to use
this navigation. (P117)
a Press the button and then press
the
button.
b Press the button.
c Select Apps.
d Select Help.
e Select a help topic.
Select to search help topics by
keyword.
You can also display a help topic to
select on each menu screen.
11
Quick Reference Guide
Voice Control Operation
Voice Portal Screen
a Press and release the button.
The system prompts you to say a voice
co
mmand. Press and release the
button again to bypass this prompt.
The system beeps when ready for a
co
mmand. Press the button or the
button to cancel.
b Say Navigation.”
The Voice Command screen is
disp
layed.
After that, follow the voice prompt
an
d say a voice command.
The audio system is muted during voice
control mode.
You can use other voice commands on
the Vo
ice Portal screen.
Disable Vo
ice Prompts to bypass the
voice prompt.
See the Owner's Manual.
Carefully read the usage note for the
voice c
ontrol.
Voice Control System (P17)
The system recognizes only certain
co
mmands.
Available navigation commands
(P13
6 )
Voice Command Screen
a After saying Navigation” from
the Voice Portal screen, the below
screen ap
pears.
b Listen for the voice prompt, then say a
voice command.
You do not need to press the
button again in the Voice Command
screen.
Available voice commands are
hig
hlighted on the screen.
12
Quick Reference Guide
Troubleshooting
For more Information (P121 )
Why does the vehicle position icon on the map appear
slightly off my actual position, especially at intersections?
This is normal. The navigation system is unaware of the
width of intersections. Large differences in vehicle position
can indicate a temporary loss of the GPS signal.
Why does the “Arrival time” display sometimes increase
even though I am getting closer to my destination?
The “Arrival time” is based on the speed limit on each
road. Depending on the traffic conditions, the “Arrival
time” may be calculated to be earlier or later.
Why does my clock frequently change the time forward
and backward by one hour?
The clock setting is automatically updated based on your
GPS location. If you are driving near a time zone border,
the automatic update likely is the reason.
How do I turn on the navigation system voice guidance?
1.Press the button and then press the button.
Select Settings > Na
vigation and enable Voice
Prompts.
2.Press the button.
Select Settings > System > S
ound/Beep tab.
Turn up Gu
idance Volume, if volume level is low.
For more details, see the Owner’s Manual.
How do I specify a destination when an entered city or
street could not be found?
Try selecting the destination directly from the map.
13
How to Use This Manual
This section explains different methods on how you can easily find information in this manual.
Searching the Table of Contents
(P1 )
First, find the general chapter related to
what you are looking for (e.g., entering
a destination from the Saved Places).
Then, go to that chapter to view a more
specific table of contents.
Searching the Index
(P139)
This more detailed table of contents
shows you exactly what information is
listed by section and title.
The Index consists of
main terms and sub-
entries. The sub-entries
help you get to the
desired page depending
on what you are looking
for.
Table of Contents
Chapter Contents
Navigation Screen
Index
Two types of Tables of Contents help
you find your desired information.
Menu items displayed on the
navigation screen (e.g., Saved) can be
found individually in the Index.
More Detailed
Contents
Go to the
Next Page
14
uuEntering a DestinationuSaved
Navigation
Saved
H uuSaved
Select a saved location to use as the destination.
1. Select your destination from the
list.
2. Select Go! to set the route to your
destination.
2 Calculating the Route P. 74
Recent
H uuRecent
Select an address from a list of your 50 most recent destinations to use as the
dti ti Th li t i di l d ith th t td ti ti tth t
1 Saved
You can add, edit, or delete the saved place.
2 Saved Locations P. 19
Using Voice Command
You can utilize a saved place by using voice
commands.
From the Voice Portal screen, say Navigation.
Say Saved Place” on the voice command screen,
then say a saved place (e.g., Honda”).
Say View List” if you want to conrm all saved
places.
Say Navigate” or “Yes” to set the route.
2 Using Voice Commands P. 5
2 Voice Con
trol Operation P. 11
1 Recent
If you want to delete all recent destinations, select
or select and then select Clear.
Select the item on the system
control panel.
Menu Tree
The menu tree helps guide you
through the system’s menu options.
To get to your desired function, follow
the menu tree in order of the steps
shown.
Select the menu option.
After following the menu
tree, step-by-step
instructions explain how to
achieve the desired result.
* Sample pages and images in this section may differ from the actual ones.
Select Saved.
Saved
15
System Setup
This section describes the start-up procedure and the navigation and setup functions.
Start-up ....................................................16
Voice Control System .......
.......................17
Voice Recognition ...................................17
Personal Information........
.......................18
Setting Home Location............................18
Saved Locations ......................................19
Display Mode Settings .....
.......................26
Switching Display Mode Manually ...........26
Map & Vehicle ...................
.......................28
Vehicle....................................................29
Driving Map View (Map Orientation) .......30
Map Detail..............................................31
Map Theme ............................................32
Map Buttons...........................................33
Map Layers ............................................ 34
Dashboards............................................ 34
myMaps................................................. 35
Navigation......
......................................... 36
Calculation Mode................................... 37
Avoidances ............................................ 38
Custom Avoidances ............................... 39
Traffic..............
......................................... 44
Other Settings.....................
.................... 45
Units ...................................................... 45
Language & Keyboard............................ 46
Device.................................................... 49
Data Reset ......
......................................... 51
Reset Factory Default Settings ................ 51
16
System Setup
Start-up
The navigation system starts automatically when you set the power mode to
ACCESSORY or ON. At start-up, the following confirmation screen is displayed.
1. Select OK.
u The HOME screen is displayed.
u If you do not select OK, the
system will automatically select
OK after a certain period of
time.
u The system
will automatically
start up the feature that was
used the last time.
2. Press the button.
u The map screen is displayed.
u When you want to display the
navigation top screen, you
press the button.
Certain manual functions are disabled or inope
rable while the vehicle is in motion.
You cannot select a grayed-out option until the vehicle is stopped.
Voice commands are still operable while the vehicle is in motion.
1 Start-up
Avoid focusing on the screen and drive safely.
When you use the navigation system, the system may
close other apps.
When you select Navigation, the system displays the
navigation feature that was used the last time. At
start-up, the navigation top screen is displayed.
Limitations for Manual Operation
17
System Setup
Voice Control System
Your vehicle has a voice control system that allows hands-free operation of the
navigation system functions.
The voice control sy
stem uses the and buttons on the steering wheel and a
microphone near the map lights on the ceiling.
For details of the button, button and microphone position, see the Owner's
Manual.
Voice Recognition
To achieve optimum voice recognition when using the navigation voice control
system:
Make sure the correct screen is displayed for the voice command that you are
using. The system recognizes only certain commands.
Available navigation commands:
2 Navigation Commands P. 136
Close the windows and moonroof
*
.
Adjust the dashboard and side vents so air does not blow onto the microphone
on the ceiling.
Speak in a clear, natural speaking voice without pausing between words.
Reduce any background noise if possible. The
system may misinterpret your
command if more than one person is speaking at the same time.
1 Voice Control System
When you press the button, the system prompts
you to say a voice command. Press and release the
button again to bypass this prompt and give a
command.
1 Voice Recognition
The voice control system can only be used from the
driver’s seat because the microphone unit removes
noises from the passenger’s side.
* Not available on all models
18
System Setup
Personal Information
Setting Home Location
H u u
Use the personal information menu to set your home location.
1. Select Set Home Location.
2. Select an
option.
u Select Us
e Current Location
to set home location.
u If selecting Enter My Address
or Recently Found, proceed to
steps 3 and 4.
3. Select
the home location.
4. Select Select.
The following options are available:
E
nter My Address: Sets the home location by entering the address.
2 Storing Your Home Address P. 8
Use Current Location: Sets your current location as your home location.
Recen
tly Found: Sets the home location from a recently found location.
1 Personal Information
You can also display the same screen by selecting
on the Where To? screen.
If you want to delete a shortcut(s), select Remove
Shortcut(s).
2 Deleting Shortcuts P. 59
The home location can be overwritten.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143

Honda Civic Si Coupe Owner's manual

Category
Car navigation systems
Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI