PAGE 1
Undermount Stainless Steel Sink
Installation Instructions
Before You Start
• Schön recommends that all undermount sinks be installed by an experienced, professional installer.
• IMPORTANT: The enclosed cutout template will create a countertop opening with a minimal (1/8” or less) reveal. It is
recommended that you discuss with your installer and agree that the nished appearance is the desired effect. Schön is not
responsible for improper sink or countertop installations.
• IMPORTANT: The cabinet must be installed, secured, plumb, and level. Failure of this step can lead to product damage.
• Schön undermount sinks should only be fastened to a solid surface countertop (i.e. granite, Corian® or Silestone®).
• Schön is not responsible for sink or countertop if damaged during installation. Be sure to inspect the sink for damage prior to
beginning installation.
• Metal edges may be sharp – use caution when handling.
• Follow all local plumbing and building codes.
Recommended Tools & Materials (Not Included)
Tape Measure
Safety Glasses
Painter’s Tape
Level
Framing Square
Pencil (not permanent marker)
Shims or Cabinet Fillers
Denatured Alcohol
Clamps
Construction Adhesive
Silicone Sealant
Screws (recommended by countertop manufacturer)
Contact Soleil Sinks at (678) 445-4638 or visit www.soleilsinks.com. Copyright ©2016, Soleil Sink Company Inc. All rights reserved.
PAGE 1
Undermount Stainless Steel Sink
Installation Instructions
Before You Start
• Soleil recommends that all undermount sinks be installed by an experienced, professional installer.
• IMPORTANT: The enclosed cutout template will create a countertop opening with a minimal (1/8” or less) reveal. It is
recommended that you discuss with your installer and agree that the finished appearance is the desired effect. Soleil is not
responsible for improper sink or countertop installations.
• IMPORTANT: The cabinet must be installed, secured, plumb, and level. Failure of this step can lead to product damage.
• Soleil undermount sinks should only be fastened to a solid surface countertop (i.e. granite, Corian® or Silestone®).
• Soleil is not responsible for sink or countertop if damaged during installation. Be sure to inspect the sink for damage prior to
beginning installation.
• Metal edges may be sharp – use caution when handling.
• Follow all local plumbing and building codes.
Recommended Tools & Materials (Not Included)
� Tape Measure
� Safety Glasses
� Painter’s Tape
� Level
� Framing Square
� Pencil (not permanent marker)
� Shims or Cabinet Fillers
� Denatured Alcohol
� Clamps
� Construction Adhesive
� Silicone Sealant
� Screws (recommended by countertop manufacturer)
Contact Soleil Sinks at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 1
Undermount Stainless Steel Sink
Installation Instructions
Before You Start
• Soleil recommends that all undermount sinks be installed by an experienced, professional installer.
• IMPORTANT: The enclosed cutout template will create a countertop opening with a minimal (1/8” or less) reveal. It is
recommended that you discuss with your installer and agree that the finished appearance is the desired effect. Soleil is not
responsible for improper sink or countertop installations.
• IMPORTANT: The cabinet must be installed, secured, plumb, and level. Failure of this step can lead to product damage.
• Soleil undermount sinks should only be fastened to a solid surface countertop (i.e. granite, Corian® or Silestone®).
• Soleil is not responsible for sink or countertop if damaged during installation. Be sure to inspect the sink for damage prior to
beginning installation.
• Metal edges may be sharp – use caution when handling.
• Follow all local plumbing and building codes.
Recommended Tools & Materials (Not Included)
� Tape Measure
� Safety Glasses
� Painter’s Tape
� Level
� Framing Square
� Pencil (not permanent marker)
� Shims or Cabinet Fillers
� Denatured Alcohol
� Clamps
� Construction Adhesive
� Silicone Sealant
� Screws (recommended by countertop manufacturer)
Undermount Stainless Steel Sink
Installation Instructions
FOR MODELS: SS604016, SS4060RV16, SS604018, SS4060RV18, SS505016, SS505018, SS703016, SS3070RV16, SS703018, SS3070RV18, SSSB301816, SSSB301818, SSSDB18,
SSSBL18, SSSBR18, SSSBMB18, SSSBSB18, SSRASB321916, SSRA604016, SSRA505016, SSRASB231916, SSRASB152016, SSSLB18, SSLD505018, SSSBE18
Tape Measure
Safety Glasses
Painter’s Tape
Level
Framing Square
Pencil (not permanent marker)
Shims or Cabinet Fillers
Denatured Alcohol
Clamps
Construction Adhesive
Silicone Sealant
Screws (recommended by countertop manufacturer)
Recommended Tools & Materials (Not Included)
: Soleil recommends that all undermount sinks be installed by an experienced, professional installer.
: IMPORTANT: The enclosed cutout template will create a countertop opening with a minimal (1/8” or less) reveal. It is
responsible for improper sink or countertop installations.
: IMPORTANT: The cabinet must be installed, secured, plumb, and level. Failure of this step can lead to product damage.
: Soleil undermount sinks should only be fastened to a solid surface countertop (i.e. granite, Corian® or Silestone®).
: Soleil is not responsible for sink or countertop if damaged during installation. Be sure to inspect the sink for damage prior to
beginning installation.
: Metal edges may be sharp – use caution when handling.
: Follow all local plumbing and building codes.
Before You Start
SS50516, SS505018 SSAPLG16
SSAPL604016 SSAPLG16
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 1
recommended that you discuss with your installer and agree that this nished appearance is the desired eect. Soleil is not
50/50 Double Bowl Kitchen Sink 60/40 Double Bowl Kitchen Sink
D-Shaped Single Bowl Kitchen Sink Single Bowl Vanity Sink
50/50 Double Bowl Kitchen Sink 60/40 Double Bowl Kitchen Sink
D-Shaped Single Bowl Kitchen Sink Single Bowl Vanity Sink
50/50 Double Bowl Kitchen Sink 60/40 Double Bowl Kitchen Sink
D-Shaped Single Bowl Kitchen Sink Single Bowl Vanity Sink
Contact Schön at (800) 880-8164 or visit www.schonsimplymodern.com. Copyright ©2017, World Imports Decorative Plumbing. All rights reserved.
Undermount Stainless Steel Sink
Installation Instructions
1: PREP COUNTERTOP
1. Position the template (provided with your sink) front to rear so the sink
will not interfere with the cabinet; secure with tape.
2. Trace the template and remove. Dry t the sink to verify the
measurements.
3. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the inside of the traced line.
4. Locate and drill the mounting holes, following the countertop
manufacturer’s instructions. Holes should allow even spacing of
mounting brackets around the sink.
5. With the countertop inverted (upside down), fasten the mounting
brackets to the countertop loosely.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Schön undermount sinks should only be fastened to a solid
surface countertop (i.e. granite, Corian® or Silestone®).
Undermount Stainless Steel Sink
Installation Instructions
1: PREP COUNTERTOP
1. Position the template (provided with your sink) front to rear so the sink
will not interfere with the cabinet; secure with tape.
2. Trace the template and remove. Dry fit the sink to verify the
measurements.
3. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the inside of the traced line.
4. Locate and drill the mounting holes, following the countertop
manufacturer’s instructions. Holes should allow even spacing of
mounting brackets around the sink.
5. With the countertop inverted (upside down), fasten the mounting
brackets to the countertop loosely.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil undermount sinks should only be fastened to a solid
surface countertop (i.e. granite, Corian® or Silestone®).
Undermount Stainless Steel Sink
Installation Instructions
1: PREP COUNTERTOP
1. Position the template (provided with your sink) front to rear so the sink
will not interfere with the cabinet; secure with tape.
2. Trace the template and remove. Dry fit the sink to verify the
measurements.
3. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the inside of the traced line.
4. Locate and drill the mounting holes, following the countertop
manufacturer’s instructions. Holes should allow even spacing of
mounting brackets around the sink.
5. With the countertop inverted (upside down), fasten the mounting
brackets to the countertop loosely.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil undermount sinks should only be fastened to a solid
surface countertop (i.e. granite, Corian® or Silestone®).
hts reserved.
Undermount Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
1: PREP COUNTERTOP
1. Position the template (provided with your sink) front to rear so the sink
will not interfere with the cabinet; secure with tape.
2.
measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the inside of the traced line.
5. Locate and drill the mounting holes, following the countertop
manufacturer’s instructions. Holes should allow even spacing of
mounting brackets around the sink.
6. With the countertop inverted (upside down), fasten the mounting
brackets to the countertop loosely.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil undermount sinks should only be fastened to a solid
surface countertop (i.e. granite, Corian® or Silestone®).
1.
sink with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant evenly all around the
3. Position and align the sink over the countertop opening. Press silicone
onto countertop.
4. Tighten fasteners until mounting brackets are snug against sink. Check
alignment of sink to the countertop opening.
5. Tighten down fasteners evenly. Be careful not to over-tighten.
6. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening
with a minimal (1/8” or less) reveal. It is recommended that you discuss this
Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged
during installation. Be sure to inspect the sink for damage prior to beginning
installation.
2: INSTALL COUNTERTOP
3: FINAL STEPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:
Soleil Sink Company Inc.
820 Shallowford Rd
Kennesaw, GA 30144
(678) 445-4638
OUTLINE FOR UNDERMOUNT
SINK CUTOUT
MOUNTING BRACKET
INVERTED COUNTERTOP
FASTENER
APPLY SILICONE SEALANT AFTER CLEANING THE
SINK EDGE AND COUNTERTOP
VERIFY SINK IS CENTERED WITHIN THE COUNTERTOP
OPENING BEFORE TIGHTENING FASTENERS.
2: INSTALL COUNTERTOP
1. Clean the bottom of the countertop and the top flange (or lip) of the sink
with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant evenly all around the
top of the sink flanges.
3. Position and align the sink over the countertop opening. Press silicone
onto countertop.
4. Tighten fasteners until mounting brackets are snug against sink. Check
alignment of sink to the countertop opening.
5. Tighten down fasteners evenly. Be careful not to over-tighten.
6. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening
with a minimal (1/8” or less) reveal. It is recommended that you discuss this
with your installer and agree that this finished appearance is the desired effect.
Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged
during installation. Be sure to inspect the sink for damage prior to beginning
installation.
hts reserved.
Undermount Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
1: PREP COUNTERTOP
1. Position the template (provided with your sink) front to rear so the sink
will not interfere with the cabinet; secure with tape.
2.
measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the inside of the traced line.
5. Locate and drill the mounting holes, following the countertop
manufacturer’s instructions. Holes should allow even spacing of
mounting brackets around the sink.
6. With the countertop inverted (upside down), fasten the mounting
brackets to the countertop loosely.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil undermount sinks should only be fastened to a solid
surface countertop (i.e. granite, Corian® or Silestone®).
1.
sink with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant evenly all around the
3. Position and align the sink over the countertop opening. Press silicone
onto countertop.
4. Tighten fasteners until mounting brackets are snug against sink. Check
alignment of sink to the countertop opening.
5. Tighten down fasteners evenly. Be careful not to over-tighten.
6. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening
with a minimal (1/8” or less) reveal. It is recommended that you discuss this
Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged
during installation. Be sure to inspect the sink for damage prior to beginning
installation.
2: INSTALL COUNTERTOP
3: FINAL STEPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:
Soleil Sink Company Inc.
820 Shallowford Rd
Kennesaw, GA 30144
(678) 445-4638
OUTLINE FOR UNDERMOUNT
SINK CUTOUT
MOUNTING BRACKET
INVERTED COUNTERTOP
FASTENER
APPLY SILICONE SEALANT AFTER CLEANING THE
SINK EDGE AND COUNTERTOP
VERIFY SINK IS CENTERED WITHIN THE COUNTERTOP
OPENING BEFORE TIGHTENING FASTENERS.
3: FINAL STEPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:
Soleil Sink Company Inc.
820 Shallowford Rd
Kennesaw, GA 30144
(678) 445-4638
PAGE 2
Contact Soleil Sinks at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
2: INSTALL COUNTERTOP
1. Clean the bottom of the countertop and the top flange (or lip) of the sink
with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant evenly all around the
top of the sink flanges.
3. Position and align the sink over the countertop opening. Press silicone
onto countertop.
4. Tighten fasteners until mounting brackets are snug against sink. Check
alignment of sink to the countertop opening.
5. Tighten down fasteners evenly. Be careful not to over-tighten.
6. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening
with a minimal (1/8” or less) reveal. It is recommended that you discuss this
with your installer and agree that this finished appearance is the desired effect.
Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged
during installation. Be sure to inspect the sink for damage prior to beginning
installation.
Undermount Stainless Steel Sink
Installation Instructions
1: PREP COUNTERTOP
1. Position the template (provided with your sink) front to rear so the sink
will not interfere with the cabinet; secure with tape.
2. Trace the template and remove. Dry fit the sink to verify the
measurements.
3. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the inside of the traced line.
4. Locate and drill the mounting holes, following the countertop
manufacturer’s instructions. Holes should allow even spacing of
mounting brackets around the sink.
5. With the countertop inverted (upside down), fasten the mounting
brackets to the countertop loosely.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil undermount sinks should only be fastened to a solid
surface countertop (i.e. granite, Corian® or Silestone®).
hts reserved.
Undermount Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
1: PREP COUNTERTOP
1. Position the template (provided with your sink) front to rear so the sink
will not interfere with the cabinet; secure with tape.
2.
measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the inside of the traced line.
5. Locate and drill the mounting holes, following the countertop
manufacturer’s instructions. Holes should allow even spacing of
mounting brackets around the sink.
6. With the countertop inverted (upside down), fasten the mounting
brackets to the countertop loosely.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil undermount sinks should only be fastened to a solid
surface countertop (i.e. granite, Corian® or Silestone®).
1.
sink with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant evenly all around the
3. Position and align the sink over the countertop opening. Press silicone
onto countertop.
4. Tighten fasteners until mounting brackets are snug against sink. Check
alignment of sink to the countertop opening.
5. Tighten down fasteners evenly. Be careful not to over-tighten.
6. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening
with a minimal (1/8” or less) reveal. It is recommended that you discuss this
Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged
during installation. Be sure to inspect the sink for damage prior to beginning
installation.
2: INSTALL COUNTERTOP
3: FINAL STEPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:
Soleil Sink Company Inc.
820 Shallowford Rd
Kennesaw, GA 30144
(678) 445-4638
OUTLINE FOR UNDERMOUNT
SINK CUTOUT
MOUNTING BRACKET
INVERTED COUNTERTOP
FASTENER
APPLY SILICONE SEALANT AFTER CLEANING THE
SINK EDGE AND COUNTERTOP
VERIFY SINK IS CENTERED WITHIN THE COUNTERTOP
OPENING BEFORE TIGHTENING FASTENERS.
2: INSTALL COUNTERTOP
1. Clean the bottom of the countertop and the top flange (or lip) of the sink
with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant evenly all around the
top of the sink flanges.
3. Position and align the sink over the countertop opening. Press silicone
onto countertop.
4. Tighten fasteners until mounting brackets are snug against sink. Check
alignment of sink to the countertop opening.
5. Tighten down fasteners evenly. Be careful not to over-tighten.
6. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening
with a minimal (1/8” or less) reveal. It is recommended that you discuss this
with your installer and agree that this finished appearance is the desired effect.
Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged
during installation. Be sure to inspect the sink for damage prior to beginning
installation.
hts reserved.
Undermount Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
1: PREP COUNTERTOP
1. Position the template (provided with your sink) front to rear so the sink
will not interfere with the cabinet; secure with tape.
2.
measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the inside of the traced line.
5. Locate and drill the mounting holes, following the countertop
manufacturer’s instructions. Holes should allow even spacing of
mounting brackets around the sink.
6. With the countertop inverted (upside down), fasten the mounting
brackets to the countertop loosely.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil undermount sinks should only be fastened to a solid
surface countertop (i.e. granite, Corian® or Silestone®).
1.
sink with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant evenly all around the
3. Position and align the sink over the countertop opening. Press silicone
onto countertop.
4. Tighten fasteners until mounting brackets are snug against sink. Check
alignment of sink to the countertop opening.
5. Tighten down fasteners evenly. Be careful not to over-tighten.
6. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening
with a minimal (1/8” or less) reveal. It is recommended that you discuss this
Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged
during installation. Be sure to inspect the sink for damage prior to beginning
installation.
2: INSTALL COUNTERTOP
3: FINAL STEPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:
Soleil Sink Company Inc.
820 Shallowford Rd
Kennesaw, GA 30144
(678) 445-4638
OUTLINE FOR UNDERMOUNT
SINK CUTOUT
MOUNTING BRACKET
INVERTED COUNTERTOP
FASTENER
APPLY SILICONE SEALANT AFTER CLEANING THE
SINK EDGE AND COUNTERTOP
VERIFY SINK IS CENTERED WITHIN THE COUNTERTOP
OPENING BEFORE TIGHTENING FASTENERS.
3: FINAL STEPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:
Soleil Sink Company Inc.
820 Shallowford Rd
Kennesaw, GA 30144
(678) 445-4638
PAGE 2
Contact Soleil Sinks at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
3: FINAL STEPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:
Soleil Sink Company Inc.
4170 JVL Industrial Park Drive
Marietta, GA 30066
(678) 445-4638
PAGE 2
Contact Soleil Sinks at (678) 445-4638 or visit www.soleilsinks.com. Copyright 2016, Soleil Sink Company Inc. All rights reserved.
2: INSTALL COUNTERTOP
1. Clean the bottom of the countertop and the top ange (or lip) of the sink
with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant evenly all around the
top of the sink anges.
3. Position and align the sink over the countertop opening. Press silicone
onto countertop.
4. Tighten fasteners until mounting brackets are snug against sink. Check
alignment of sink to the countertop opening.
5. Tighten down fasteners evenly. Be careful not to over-tighten.
6. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening
with a minimal (1/8” or less) reveal. It is recommended that you discuss this
with your installer and agree that this nished appearance is the desired effect.
Schön is not responsible for improper sink or countertop installations.
IMPORTANT: Schön is not responsible for sink or countertop if damaged
during installation. Be sure to inspect the sink for damage prior to beginning
installation.
Undermount Stainless Steel Sink
Installation Instructions
1: PREP COUNTERTOP
1. Position the template (provided with your sink) front to rear so the sink
will not interfere with the cabinet; secure with tape.
2. Trace the template and remove. Dry fit the sink to verify the
measurements.
3. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the inside of the traced line.
4. Locate and drill the mounting holes, following the countertop
manufacturer’s instructions. Holes should allow even spacing of
mounting brackets around the sink.
5. With the countertop inverted (upside down), fasten the mounting
brackets to the countertop loosely.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil undermount sinks should only be fastened to a solid
surface countertop (i.e. granite, Corian® or Silestone®).
Undermount Stainless Steel Sink
Installation Instructions
1: PREP COUNTERTOP
1. Position the template (provided with your sink) front to rear so the sink
will not interfere with the cabinet; secure with tape.
2. Trace the template and remove. Dry fit the sink to verify the
measurements.
3. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the inside of the traced line.
4. Locate and drill the mounting holes, following the countertop
manufacturer’s instructions. Holes should allow even spacing of
mounting brackets around the sink.
5. With the countertop inverted (upside down), fasten the mounting
brackets to the countertop loosely.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil undermount sinks should only be fastened to a solid
surface countertop (i.e. granite, Corian® or Silestone®).
hts reserved.
Undermount Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
1: PREP COUNTERTOP
1. Position the template (provided with your sink) front to rear so the sink
will not interfere with the cabinet; secure with tape.
2.
measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the inside of the traced line.
5. Locate and drill the mounting holes, following the countertop
manufacturer’s instructions. Holes should allow even spacing of
mounting brackets around the sink.
6. With the countertop inverted (upside down), fasten the mounting
brackets to the countertop loosely.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil undermount sinks should only be fastened to a solid
surface countertop (i.e. granite, Corian® or Silestone®).
1.
sink with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant evenly all around the
3. Position and align the sink over the countertop opening. Press silicone
onto countertop.
4. Tighten fasteners until mounting brackets are snug against sink. Check
alignment of sink to the countertop opening.
5. Tighten down fasteners evenly. Be careful not to over-tighten.
6. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening
with a minimal (1/8” or less) reveal. It is recommended that you discuss this
Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged
during installation. Be sure to inspect the sink for damage prior to beginning
installation.
2: INSTALL COUNTERTOP
3: FINAL STEPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:
Soleil Sink Company Inc.
820 Shallowford Rd
Kennesaw, GA 30144
(678) 445-4638
OUTLINE FOR UNDERMOUNT
SINK CUTOUT
MOUNTING BRACKET
INVERTED COUNTERTOP
FASTENER
APPLY SILICONE SEALANT AFTER CLEANING THE
SINK EDGE AND COUNTERTOP
VERIFY SINK IS CENTERED WITHIN THE COUNTERTOP
OPENING BEFORE TIGHTENING FASTENERS.
2: INSTALL COUNTERTOP
1. Clean the bottom of the countertop and the top flange (or lip) of the sink
with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant evenly all around the
top of the sink flanges.
3. Position and align the sink over the countertop opening. Press silicone
onto countertop.
4. Tighten fasteners until mounting brackets are snug against sink. Check
alignment of sink to the countertop opening.
5. Tighten down fasteners evenly. Be careful not to over-tighten.
6. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening
with a minimal (1/8” or less) reveal. It is recommended that you discuss this
with your installer and agree that this finished appearance is the desired effect.
Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged
during installation. Be sure to inspect the sink for damage prior to beginning
installation.
hts reserved.
Undermount Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
1: PREP COUNTERTOP
1. Position the template (provided with your sink) front to rear so the sink
will not interfere with the cabinet; secure with tape.
2.
measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the inside of the traced line.
5. Locate and drill the mounting holes, following the countertop
manufacturer’s instructions. Holes should allow even spacing of
mounting brackets around the sink.
6. With the countertop inverted (upside down), fasten the mounting
brackets to the countertop loosely.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil undermount sinks should only be fastened to a solid
surface countertop (i.e. granite, Corian® or Silestone®).
1.
sink with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant evenly all around the
3. Position and align the sink over the countertop opening. Press silicone
onto countertop.
4. Tighten fasteners until mounting brackets are snug against sink. Check
alignment of sink to the countertop opening.
5. Tighten down fasteners evenly. Be careful not to over-tighten.
6. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening
with a minimal (1/8” or less) reveal. It is recommended that you discuss this
Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged
during installation. Be sure to inspect the sink for damage prior to beginning
installation.
2: INSTALL COUNTERTOP
3: FINAL STEPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:
Soleil Sink Company Inc.
820 Shallowford Rd
Kennesaw, GA 30144
(678) 445-4638
OUTLINE FOR UNDERMOUNT
SINK CUTOUT
MOUNTING BRACKET
INVERTED COUNTERTOP
FASTENER
APPLY SILICONE SEALANT AFTER CLEANING THE
SINK EDGE AND COUNTERTOP
VERIFY SINK IS CENTERED WITHIN THE COUNTERTOP
OPENING BEFORE TIGHTENING FASTENERS.
3: FINAL STEPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:
Soleil Sink Company Inc.
820 Shallowford Rd
Kennesaw, GA 30144
(678) 445-4638
PAGE 2
Contact Soleil Sinks at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
2: INSTALL COUNTERTOP
1. Clean the bottom of the countertop and the top flange (or lip) of the sink
with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant evenly all around the
top of the sink flanges.
3. Position and align the sink over the countertop opening. Press silicone
onto countertop.
4. Tighten fasteners until mounting brackets are snug against sink. Check
alignment of sink to the countertop opening.
5. Tighten down fasteners evenly. Be careful not to over-tighten.
6. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening
with a minimal (1/8” or less) reveal. It is recommended that you discuss this
with your installer and agree that this finished appearance is the desired effect.
Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged
during installation. Be sure to inspect the sink for damage prior to beginning
installation.
Undermount Stainless Steel Sink
Installation Instructions
1: PREP COUNTERTOP
1. Position the template (provided with your sink) front to rear so the sink
will not interfere with the cabinet; secure with tape.
2. Trace the template and remove. Dry fit the sink to verify the
measurements.
3. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the inside of the traced line.
4. Locate and drill the mounting holes, following the countertop
manufacturer’s instructions. Holes should allow even spacing of
mounting brackets around the sink.
5. With the countertop inverted (upside down), fasten the mounting
brackets to the countertop loosely.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil undermount sinks should only be fastened to a solid
surface countertop (i.e. granite, Corian® or Silestone®).
hts reserved.
Undermount Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
1: PREP COUNTERTOP
1. Position the template (provided with your sink) front to rear so the sink
will not interfere with the cabinet; secure with tape.
2.
measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the inside of the traced line.
5. Locate and drill the mounting holes, following the countertop
manufacturer’s instructions. Holes should allow even spacing of
mounting brackets around the sink.
6. With the countertop inverted (upside down), fasten the mounting
brackets to the countertop loosely.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil undermount sinks should only be fastened to a solid
surface countertop (i.e. granite, Corian® or Silestone®).
1.
sink with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant evenly all around the
3. Position and align the sink over the countertop opening. Press silicone
onto countertop.
4. Tighten fasteners until mounting brackets are snug against sink. Check
alignment of sink to the countertop opening.
5. Tighten down fasteners evenly. Be careful not to over-tighten.
6. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening
with a minimal (1/8” or less) reveal. It is recommended that you discuss this
Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged
during installation. Be sure to inspect the sink for damage prior to beginning
installation.
2: INSTALL COUNTERTOP
3: FINAL STEPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:
Soleil Sink Company Inc.
820 Shallowford Rd
Kennesaw, GA 30144
(678) 445-4638
OUTLINE FOR UNDERMOUNT
SINK CUTOUT
MOUNTING BRACKET
INVERTED COUNTERTOP
FASTENER
APPLY SILICONE SEALANT AFTER CLEANING THE
SINK EDGE AND COUNTERTOP
VERIFY SINK IS CENTERED WITHIN THE COUNTERTOP
OPENING BEFORE TIGHTENING FASTENERS.
2: INSTALL COUNTERTOP
1. Clean the bottom of the countertop and the top flange (or lip) of the sink
with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant evenly all around the
top of the sink flanges.
3. Position and align the sink over the countertop opening. Press silicone
onto countertop.
4. Tighten fasteners until mounting brackets are snug against sink. Check
alignment of sink to the countertop opening.
5. Tighten down fasteners evenly. Be careful not to over-tighten.
6. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening
with a minimal (1/8” or less) reveal. It is recommended that you discuss this
with your installer and agree that this finished appearance is the desired effect.
Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged
during installation. Be sure to inspect the sink for damage prior to beginning
installation.
hts reserved.
Undermount Stainless Steel Sink
Installation Instructions
Contact Soleil at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
PAGE 2
1: PREP COUNTERTOP
1. Position the template (provided with your sink) front to rear so the sink
will not interfere with the cabinet; secure with tape.
2.
measurements.
4. Following the countertop manufacturer’s instructions, carefully cut the
countertop on the inside of the traced line.
5. Locate and drill the mounting holes, following the countertop
manufacturer’s instructions. Holes should allow even spacing of
mounting brackets around the sink.
6. With the countertop inverted (upside down), fasten the mounting
brackets to the countertop loosely.
IMPORTANT: The cabinet must be installed, secured, plumb, and level BEFORE
installing the sink.
IMPORTANT: Soleil undermount sinks should only be fastened to a solid
surface countertop (i.e. granite, Corian® or Silestone®).
1.
sink with denatured alcohol.
2. Apply a narrow bead of silicone adhesive sealant evenly all around the
3. Position and align the sink over the countertop opening. Press silicone
onto countertop.
4. Tighten fasteners until mounting brackets are snug against sink. Check
alignment of sink to the countertop opening.
5. Tighten down fasteners evenly. Be careful not to over-tighten.
6. Immediately remove excess sealant.
IMPORTANT: The enclosed cutout template will create a countertop opening
with a minimal (1/8” or less) reveal. It is recommended that you discuss this
Soleil is not responsible for improper sink or countertop installations.
IMPORTANT: Soleil is not responsible for sink or countertop if damaged
during installation. Be sure to inspect the sink for damage prior to beginning
installation.
2: INSTALL COUNTERTOP
3: FINAL STEPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:
Soleil Sink Company Inc.
820 Shallowford Rd
Kennesaw, GA 30144
(678) 445-4638
OUTLINE FOR UNDERMOUNT
SINK CUTOUT
MOUNTING BRACKET
INVERTED COUNTERTOP
FASTENER
APPLY SILICONE SEALANT AFTER CLEANING THE
SINK EDGE AND COUNTERTOP
VERIFY SINK IS CENTERED WITHIN THE COUNTERTOP
OPENING BEFORE TIGHTENING FASTENERS.
3: FINAL STEPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:
Soleil Sink Company Inc.
820 Shallowford Rd
Kennesaw, GA 30144
(678) 445-4638
PAGE 2
Contact Soleil Sinks at (687) 445-4638 or visit www.soleilsinks.com. Copyright ©2015, Soleil Sink Company Inc. All rights reserved.
3: FINAL STEPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.soleilsinks.com or contact Soleil directly at:
Soleil Sink Company Inc.
4170 JVL Industrial Park Drive
Marietta, GA 30066
(678) 445-4638
PAGE 2
Contact Soleil Sinks at (678) 445-4638 or visit www.soleilsinks.com. Copyright 2016, Soleil Sink Company Inc. All rights reserved.
3: FINAL STEPS
1. Following all local plumbing and building codes, install the faucet according to the manufacturer’s instructions.
2. Connect the drain and piping.
3. Run water into the sink and check all connections for leaks.
IMPORTANT: For additional information or warranty issues visit www.schonsimplymodern.com or contact Schön directly at:
Schön Warranty Dept, World Imports Decorative Plumbing
3074 Chastain Meadows Parkway
Marietta, GA 30066
(800) 880-8164
PAGE 2
Contact Schön at (800) 880-8164 or visit www.schonsimplymodern.com. Copyright ©2017, World Imports Decorative Plumbing. All rights reserved.
/
