Safety Technology International STI-9110 Operating instructions

Brand: Safety Technology International

Model: STI-9110

Type: Operating instructions

Safety Technology International STI-9110 is a lockable thermostat cover designed to protect your thermostat from tampering. It is made of clear polycarbonate and has a key lock to prevent unauthorized access. The STI-9110 is easy to install and comes with all the necessary hardware. It is also easy to clean and maintain. The STI-9110 is a great way to keep your thermostat safe and secure.

INSTALLATION OF STI-9110 LOCKABLE THERMOSTAT COVER

All speciﬁcations and information shown were current as of publication and are subject to change without notice.

9110IS JULY2017

2306 Airport Road • Waterford, Michigan 48327-1209

Phone: 248-673-9898 • Fax: 248-673-1246

Toll Free: 800-888-4784 • E-mail: [email protected]

Web: www.sti-usa.com

Taylor House • 34 Sherwood Road • Bromsgrove

Worcestershire • B60 3DR • England

Tel: +44 (0)1527 520 999 • Fax: +44 (0)1527 501 999

E-mail: [email protected] • Web: www.sti-emea.com

VIEW A

INSTALLATION INSTRUCTIONS

1. Do not remove thermostat. Prior to drilling anchor holes, cover thermostat with a damp cloth to prevent dust from

penetrating the sensor.

2. Center frame over existing thermostat. Mark and drill (4) anchor holes using a 1/4 in. (6.3mm) drill bit. Insert the

(4) anchors and complete installation as shown.

NOTE: The (3) tabs on the frame must face upward (View A).

3. Insert the (3) slots on the cover over tabs on the top surface of frame. Rotate cover downward onto the frame and

turn key to lock.

CLEANING INSTRUCTIONS

To clean cover, remove from wall. Rinse with water to remove abrasive dust and dirt. Wash with soap or mild detergent

using a soft cloth (DO NOT SCRUB). Rinse once more, then dry with a soft cloth or chamois. To remove grease or wet

paint, rub gently with a cloth wetted thoroughly with naphtha. Then wash and rinse. DO NOT USE RAZOR BLADES.

2" SPACER MUST BE USED ON ALL

SURFACE MOUNTED INSTALLATIONS

(PART #STI 3100)

FRAME

SURFACE MOUNT

THERMOSTAT

COVER AND

LOCK ASSEMBLY

STI-9110 (CLEAR)

FRAME

DRILL (4) HOLES .25"

EXISTING FLUSH

MOUNT THERMOSTAT

(6.3 mm) DIAMETER

FOR ADEQUATE CLEARANCE A

SURFACE MOUNT

(STI 9130)

FLUSH MOUNT

(STI-9110)

COVER AND

LOCK ASSEMBLY

8.45 in.

(215mm)

5.3 in.

(135mm)

3.75 in.

(95mm)

PRODUCT DIMENSIONS

THE THREE (3) COVER TABS

MUST FACE UPWARD AS SHOWN

VIEW A

COVER

FRAME

FRAME TABS

5.3 in.

(135mm)

8.45 in.

(215mm)

9.5 in.

(241mm)

7.6 in.

(193mm)

3.75 in.

(95mm)

3.9 in.

(99mm)

STI-9110

PRODUCT DIMENSIONS

FOR SURFACE MOUNT

STI-9110 AND SUB-900

FOR SURFACE MOUNT

FOR ADEQUATE CLEARANCE

A 2 in. (50mm) DEEP SPACER

MUST BE USED

(ORDER KIT-900)

SEE VIEW A

#10 x 1/2 PHILLIPS PAN

HEAD SCREW (4) PROVIDED

ANCHOR

(4) PROVIDED

9.5 in.

(241mm)

8.45 in.

(215mm)

3.9 in.

(99mm)

3.75 in.

(95mm)

5.3 in.

(135mm)

7.6 in.

(193mm)

WARNING: This product can expose you to chemicals including Dichloromethane, which

is known to the State of California to cause cancer, and Bisphenol A (BPA), which is

known to the State of California to cause birth defects or other reproductive harm. For

more information go to www.P65Warnings.ca.gov.

Three year warranty or a one year limited warranty (from date of purchase) on most

products. See website for details. Electronic warranty form at www.sti-usa.com/wc14.

Safety Technology International STI-9110 Operating instructions

Brand: Safety Technology International

Model: STI-9110

Type: Operating instructions

Download PDF

report

Safety Technology International STI-9110 Operating instructions

Safety Technology International STI-9110 Operating instructions

Related papers

Other documents