A. Side Rails (2 pcs)
B. Foot and Head Rails (2 pcs)
C. Center Support (1 pc)
D. Wood Slats (26 pcs)
E. Legs (7 pcs)
Platform Frame
Contains One (1) Frame and Hardware
PART LIST
HARDWARE LIST
ASSEMBLY INSTRUCTIONS
(Continued on back)
STEP 1
STEP 2
J. Washer
(18 pcs)
K. Hex Key
(1 pc)
L. Wrench
(1 pc)
I. Nut
(18 pcs)
H. Screw
(18 pcs)
F. Slat Holder -
Center (13 pcs)
G. Slat Holder -
Side (26 pcs)
With holes facing up, insert the side rails
(Part A) into the foot and head rails (Part B).
Attach outer six legs (Part E) to the frame using two screws
(Part H), two washers (Part J) and two nuts (Part I) per leg.
Tighten using hex key (Part K) and wrench (Part L).
B
Carefully remove all the parts from the carton. Arrange on a ๎at
surface and verify you have all of the following parts and hardware.
IMPORTANT NOTE:
Two wooden replacement slats have been
included with this frame. Do not throw them
away. Store these replacement slats in a safe
place for future use, if needed.
DB, TW SIZES
http://www.youtube.com/watch?v=2THFfPzzpG4
VIDEO
Scan the QR code on your smart phone or device, or enter the link below to watch a
complete video of the easy assembly of the Platform Frame. Please note that the video
represents assembly of a Queen Size Platform Frame.
STEP 3 STEP 4
STEP 6
ASSEMBLY INSTRUCTIONS (CONTINUED)
Attach the remaining leg (Part E) to the center
support (Part C) using two screws (Part H), two
washers (Part J) and two nuts (Part I). Tighten
using hex key (Part K) and wrench (Part L).
Put center slat holders (Part F) on one side and
side slat holders (Part G) on the other side of the
10 single slats (Part D).
Put center slat holders (Part F) on one side and
side slat holders (Part G) on the other side of the
3 double slats (Part D).
Put side slat holders (Part G) on one side of the
3 remaining double slats (Part D).
Attach the center support from Step 3 to the
frame from Step 2 using two screws (Part H), two
washers (Part J) and two nuts (Part I) per side.
Tighten using hex key (Part K) and wrench (Part L).
Attach slats to one side of the frame and center
support by pressing the pegs into the holes.
Double slats are installed in the middle.
Attach slats to the other side of the frame. Double
slats are installed in the middle. By moving the
blue sliders on the double slats closer together
you can make the middle section plusher, and by
moving them apart - make it ๎rmer.
STEP 5
STEP 8
Put side slat holders (Part G) on one side of the
10 remaining single slats (Part D).
STEP 7
B
-
1
-
2
Boyd Sleep MFPRRWSPFTW Operating instructions
- Type
- Operating instructions
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Gorilla Playsets 01-0004-3 User manual
-
-
Creative Cedar Designs 3512-Y-G User manual
-
Creative Cedar Designs 3512 Operating instructions
-
Hideaway Beds Next Bed Single Assembly Instructions Manual
-
-
Gorilla Playsets 01-0004-AP Operating instructions
-
-
-
Sears 52725165 Owner's manual
