Fire Magic Island Enclosure Wheel Kit User manual

Fire Magic
Brand
Fire Magic
Model
Island Enclosure Wheel Kit
Category
Barbecues & grills
Type
User manual
REV 1 - 1602021200
L-C2-413
1
ROBERT H. PETERSON CO. • 14724 East Proctor Avenue • City of Industry, CA 91746
This wheel kit is only for installation on Fire Magic Island Enclosure models:
DC430-CBR-75SM
DC430-CBD-75SM
DC790-CBR-108SM
DC790-CBD-108SM
INSTALLER: Leave these instructions with consumer.
CONSUMER: Retain for future reference.
ISLAND ENCLOSURE
WHEEL KIT
Model # DC-WK-03
Fig. 1-1 Overall install detail
(Left wheel assembly) (Right wheel assembly)
Refrigerator (CBR) Models
Drawer (CBD) Models
Note: Although island enclosure models
vary by design, wheel kit and wheel
kit installation is the same for all
island enclosure models.
REV 1 - 1602021200
L-C2-413
2
Prior to assembling the island enclosure, install the
wheel kit per the steps below.
1. Carefully place the left island wall upside down.
2. Align the left wheel assembly and fasten using
the included hardware and a
9
/16" open-end
wrench or equivalent (Fig. 2-1).
Note: The wheel assembly must stay level when
being installed.
3. Repeat for the right island wall using the right
wheel assembly as shown in Fig. 2-2.
Note: The wheel assembly must stay level when
being installed.
4. Follow your island instruction manual to
complete island installation.
Important: Before installing the countertop, use
the included hardware to properly
secure the wheel assemblies to the
front and rear walls.
Left side wall shown
(upside down)
(Exterior-side)
Fig. 2-1 Install left wheel assembly to bottom of
left side wall
(Keep level)
Fig. 2-2 Install right wheel assembly to bottom of
right side wall
Right side wall shown
(upside down)
(Keep level)
(Exterior-side)
430-CBR
model shown
WHEN INSTALLING ON AN UNASSEMBLED ISLAND ENCLOSURE
REV 1 - 1602021200
L-C2-413
3
WARNING: Use extreme care when installing this
wheel kit on an existing island that has
already been fully assembled. Use two
or more people when handling the island
enclosure.
1. Remove any appliances, doors, drawers, and
countertop leaving only the island frame fully-
assembled. See Fig. 3-1.
WARNING: Take into consideration any gas supply
plumbing, electrical wires, etc. when
moving/removing these items.
2. Carefully place two 2x4's under the island
enclosure as shown in Fig. 3-2. (Keep clear of
any levelers.)
3. Remove all levelers (see Fig. 3-3) and install the
left wheel assembly to the left side of the enclosure
using the included hardware and a
9
/16" open-end
wrench or equivalent (see Fig. 3-4).
Fig. 3-2 Place 2x4's under island enclosure
Fig. 3-3 Remove Levelers
Fig. 3-4 Install left wheel assembly
2x4
2x4
(2x4's not shown)
2x4
Left wheel
assembly
Fig. 3-1 Remove appliances, doors drawers, etc.
430-CBR
model shown
Procedure continued on following page
WHEN INSTALLING ON AN ASSEMBLED ISLAND ENCLOSURE
REV 1 - 1602021200
L-C2-413
4
Fig. 4-1 Install right wheel assembly
2x4
4. Carefully shift the left 2x4 to the right (a few inches
clear from the bolt nut) and completely remove
the 2x4 on the far right (allowing the left wheels
to touch the ground). Carefully align and install
the right wheel assembly as shown in Fig. 4-1.
5. Carefully lift up the right side of the island
enclosure and slowly remove the 2x4 (allowing
all wheels to touch the ground).
6. Re-install the countertop, all appliances, doors,
and drawers taking into consideration any gas
supply plumbing, electrical wires, etc. when
reinstalling. Refer to your grill instruction manual
for installation.
WHEN INSTALLING ON AN ASSEMBLED ISLAND ENCLOSURE (Cont.)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Fire Magic Island Enclosure Wheel Kit User manual

Fire Magic
Brand
Fire Magic
Model
Island Enclosure Wheel Kit
Category
Barbecues & grills
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents