Metabo SR 356 Operating instructions

Type
Operating instructions

This manual is also suitable for

Gebrauchsanleitung .............. Seite
Operating Instructions........... page
Mode d’emploi ...................... page
Gebruiksaanwijzing .........bladzijde
Istruzioni d’uso ................... pagina
Instrucciones de manejo .... página
Instruções de serviço ......... página
Bruksanvisning ....................... sida
Käyttöohje ...............................sivu
Bruksanvisning ....................... side
Betjeningsvejledning .............. side
Instrukcja obłsugi ................ strona
δηγίες ρήσεως .............Σελίδα
Használati útmutató .............. oldal
5
9
13
17
21
25
29
33
37
41
45
49
53
57
Sr 356
Sr E 357
Sr 358
Sr E 359
SRE Partner Edition
170 26 7220 - 0308
Made in Germany
17026722_0308 Sr 356.book Seite 1 Montag, 3. März 2008 11:31 11
2
Sr 356 Sr E 357 Sr 358
Sr E 359
SRE Partner
Edition
A mm (in)
92 x 190
(3
5
/
8
x 7
1
/
2
)
92 x 190
(3
5
/
8
x 7
1
/
2
)
112 x 230
(4
3
/
8
x 9)
112 x 230
(4
3
/
8
x 9)
P
1
W 350 350 350 350
P
2
W 190 190 190 190
n
0
min
-1
(rpm)
22000 12000-22000 22000 12000-22000
n
1
min
-1
(rpm)
15000 15000 15000 15000
S mm (in)
2,5 (
3
/
32
) 2,5 (
3
/
32
)2,5 (
3
/
32
) 2,5 (
3
/
32
)
m kg (lbs) 2,5 (5.5) 2,6 (5.7) 2,7 (6.0) 2,8 (6.2)
a
h
/K
h
m/s
2
7 / 1,5 7 / 1,5 7 / 1,5 7 / 1,5
L
pA
/K
pA
dB(A) 75 / 3 75 / 3 76 / 3 77 / 3
L
WA
/K
WA
dB(A) 86 / 3 86 / 3 87 / 3 88 / 3
14
EN 60745
98/37/EG (
28.12.09), 2006/42/EG (29.12.09
), 2004/108/EG
Erhard Krauß, Geschäftsführung
© 2008 Metabowerke GmbH, 72622 Nürtingen, Germany
17026722_0308 Sr 356.book Seite 2 Montag, 3. März 2008 11:31 11
3
1
2
3
3
4
4
5
5
6
6
7
Sr E 357
Sr E 359
SRE Partner Edition
8 9 10 11
17026722_0308 Sr 356.book Seite 3 Montag, 3. März 2008 11:31 11
6.31289
6.31758
6.31288
Sr 356, Sr E 357
Sr 358, Sr E 359, SRE Partner Edition
2 x P 40
2 x P 80
2 x P 120
2 x P 180
2 x P 240
6.24833
10x
P 40 6.24826
P 60 6.24827
P 80 6.24828
P 100 6.24829
P 120 6.24830
P 180 6.24831
P 240 6.24832
A
B
D
C
J
K
M
L
2 x P 40
2 x P 80
2 x P 120
2 x P 180
2 x P 240 6.24807
10x
P 40 6.24800
P 60 6.24801
P 80 6.24802
P 100 6.24803
P 120 6.24804
P 180 6.24805
P 240 6.24806
2 x P 40
2 x P 80
2 x P 120
2 x P 180
2 x P 240 6.24824
10x
P 40 6.24328
P 60 6.24329
P 80 6.24330
P 100 6.24331
P 120 6.24332
P 180 6.24333
P 240 6.24334
2 x P 40
2 x P 80
2 x P 120
2 x P 180
2 x P 240 6.24825
10x
P 40 6.24365
P 60 6.24366
P 80 6.24367
P 100 6.24368
P 120 6.24369
P 180 6.24370
P 240 6.24371
2 x P 40
2 x P 80
2 x P 120
2 x P 180
2 x P 240 6.24490
10x
P 40 6.24480
P 60 6.24481
P 80 6.24482
P 100 6.24483
P 120 6.24484
P 180 6.24485
P 240 6.24486
2 x P 40
2 x P 80
2 x P 120
2 x P 180
2 x P 240 6.24499
10x
P 40 6.24491
P 60 6.24492
P 80 6.24493
P 100 6.24494
P 120 6.24495
P 180 6.24496
P 240 6.24497
5x
P 40 6.24750
P 60 6.24751
P 80 6.24752
P 100 6.24753
P 120 6.24754
P 240 6.24755
2 x P 40
2 x P 80
2 x P 120
2 x P 180
2 x P 240 6.24815
10x
P 40 6.24808
P 60 6.24809
P 80 6.24810
P 100 6.24811
P 120 6.24812
P 180 6.24813
P 240 6.24814
2 x P 40
2 x P 80
2 x P 120
2 x P 180
2 x P 240 6.24823
10x
P 40 6.24816
P 60 6.24817
P 80 6.24818
P 100 6.24819
P 120 6.24820
P 180 6.24821
P 240 6.24822
6.24749
E
6.31148
6.31149
A
B
D
C
E
H
339160250
F
I
G
6.24709
F
339160230
H
6.24736
I
5x
P 40 6.24730
P 60 6.24731
P 80 6.24732
P 100 6.24733
P 120 6.24734
P 240 6.24735
4
17026722_0308 Sr 356.book Seite 4 Montag, 3. März 2008 11:31 11
ENGLISH
9
ENG
1 Conformity Declaration
2 Specified Use
3 General Safety Instructions
4 Special Safety Instructions
5Overview
6 Special Product Features
7 Commissioning
7.1 Additional handle
7.2 Installation of sanding disc
8Use
8.1 On/Off switch, continuous activation
8.2 Setting oscillating frequency
8.3 Dust extraction
9 Cleaning, Maintenance
10 Tips and Tricks
11 Accessories
12 Repairs
13 Environmental Protection
14 Technical Specifications
We, being solely responsible, hereby declare that
this product conforms to the standards and direc-
tives specified on page 2.
The machine is suitable for dry sanding of flat and
elliptical surfaces, wood, plastics, non-ferrous
metals, sheet metal and similar filled and painted
surfaces.
The user bears sole responsibility for damage
caused by improper use.
Generally accepted accident prevention regula-
tions and the enclosed safety information must be
observed.
WARNING
– Reading the operating
instructions will reduce the risk
of injury.
WARNING Read all safety warnings and
instructions.
Failure to follow all safety
warnings and instructions may result in electric
shock, fire and/or serious injury.
Keep all safety instructions and information for
future reference.
Before using the power tool, carefully read through
and familiarise yourself with all the enclosed safety
information and the Operating Instructions. Keep
all enclosed documentation for future reference,
and pass on your power tool only together with this
documentation.
For your own protection and for the
protection of your power tool pay atten-
tion to all parts of the text that are
marked with this symbol!
Dust from material such as paint containing lead,
some wood species, minerals and metal may be
harmful. Contact with or inhalation of the dust may
cause allergic reactions and/or respiratory
diseases to the operator or bystanders.
Certain kinds of dust are classified as carcinogenic
such as oak and beech dust especially in conjunc-
tion with additives for wood conditioning (chro-
mate, wood preservative). Material containing
asbestos must only be treated by specialists.
- Use a dust extractor or the dust bag where
possible.
- To achieve a high level of dust collection, use a
suitable Metabo vacuum cleaner together with
this tool.
- The work place must be well ventilated.
- The use of a dust mask of filter class P2 is
recommended.
Follow national requirements for the materials you
want to work with.
Pull the plug out of the plug socket before any
adjustments or servicing are performed.
Operating Instructions
Dear Customer,
Thank you for the trust you have placed in us by buying a Metabo power tool. Each Metabo power tool
is carefully tested and subject to strict quality controls by Metabo's quality assurance. Nevertheless, the
service life of a power tool depends to a great extent on you. Please observe the information contained
in these instructions and the enclosed documentation. The more carefully you treat your Metabo power
tool, the longer it will provide dependable service.
Contents
1 Conformity Declaration
2 Specified Use
3 General Safety Instructions
4 Special Safety Instructions
17026722_0308 Sr 356.book Seite 9 Montag, 3. März 2008 11:31 11
10
ENGLISH
ENG
Wear ear protectors when working for long periods
of time. High noise levels over a prolonged period
of time may affect your hearing.
Materials that generate dusts or vapours that may
be harmful to health (e.g. asbestos) must not be
processed.
Secure the workpiece against slipping, e.g. with
the help of clamping devices.
See page 3 (please unfold).
1 Sanding plate
2 Sanding disc
3 Clamp rail
4 Clamping lever
5 Additional handle (removable)
6 Knurled screw
7 Setting wheel for selecting oscillating
frequency *
8 Trigger switch
9 Locking button for continuous activation
10 Dust bag holder
11 Dust bag
Powerful motor with high power reserves
4 high-quality vibration buffers and dust-
protected high-quality ball bearings for a long
service life in continuous use
Quick-action clamping device with gummed
pressure strip
Own extraction system
Turn-off carbon brushes
Before plugging in, check to see that the
rated mains voltage and mains frequency,
as stated on the rating label, match your power
supply.
7.1 Additional handle
See illustration on page 3.
The removable additional handle (5) can be
screwed onto the machine with the integrated
knurled screw (6).
It is available with two different heights.
If required, insert a Phillips screwdriver in the hole
at the end of the additional handle to release or
tighten the knurled screw (6).
7.2 Installation of sanding disc
See illustration on page 3.
To optimise the dust extraction performance, fit
the sanding disc such that the holes on the
sanding disc (2) and sanding plate (1) are aligned.
- Swivel clamping lever (4) upwards. This opens
the clamp rail (3).
- Slide sanding disc under clamp rail.
- Swivel clamping lever downwards. This clamps
the sanding disc firmly with the clamp rail.
- Pull sanding disc tightly over the sanding plate
and also clamp firmly on the other side.
8.1 On/Off switch, continuous activation
To start the machine, press the trigger switch (8).
For continuous operation the trigger switch can be
locked using the lock button (9). To stop the
machine, press the trigger switch (8) again.
8.2 Setting oscillating frequency
Set the oscillating frequency at the setting wheel
(7). This is also possible during operation.
Recommended oscillating frequency settings:
Plastic materials . . . . . . . . . . . . . . . . . . . . . 1-2
Metal, Plexiglas, old coats of paint . . . . . . . 3-4
Coarse and fine sanding, polishing, wood . 5-6
The best way to determine the ideal setting is
through a practical trial.
8.3 Dust extraction
To optimise the dust extraction performance, fit
the sanding disc such that the holes on the
sanding disc (2) and sanding plate (1) are aligned.
Built-in extraction:
Attach the dust bag holder (10). To optimise the
extraction performance, empty the dust bag (11) in
good time or replace.
External extraction:
Remove the dust bag holder (10). Connect a suit-
able extraction device to the ejection nozzle. Use a
suction hose with a 35 mm connector diameter.
Note:
When sanding abrasive material (e.g.
plaster, etc.) we recommend connecting a suitable
dust extractor.
5Overview
6 Special Product Features
7 Commissioning
8Use
17026722_0308 Sr 356.book Seite 10 Montag, 3. März 2008 11:31 11
ENGLISH
11
ENG
Clean the machine regularly.
This includes
vacuum cleaning the ventilation louvres on the
motor.
Replacing worn sanding plate (1)
- Remove fixing screws (on lower side of sanding
plate).
- Take off sanding plate.
- For sanding plate (as replacement), refer to the
Accessories chapter.
- Mount sanding plate.
- Refit fixing screws (on lower side of sanding
plate) and tighten.
Do not press the device too firmly against the
surface being sanded. This does not improve, but
rather impairs, the sanding performance.
To optimise the extraction performance, empty the
dust bag (11) in good time or replace.
Use a suitable sanding disc to achieve the best
possible work results: Removal of old paint
layers = P 40
Pre-sanding of wood = P 60, P 80
Finishing of wood = P 100, P 120
Sanding of veneers, sealing primer, filler,
paint = P 180, P 240
Use only genuine Metabo accessories.
If you need any accessories, check with your
dealer.
For dealers to select the correct accessory, they
need to know the exact model designation of your
power tool.
See page 4.
A Perforated sanding discs,
quality finishing for wood
B Perforated sanding discs,
extra quality for wood/metal
C Non-perforated sanding discs,
quality finishing for wood
D Non-perforated sanding discs,
extra quality for wood/metal
E Hole punch
F Perforated sanding plate (as replacement)
G Self-adhesive perforated film with velcro-type
fastening. Before affixing the film, clean the
sanding plate.
H Perforated sanding plate with velcro-type
fastening
I Perforated adhesive sanding discs.
J Dust bag holder (as replacement)
K Dust bag (as replacement)
L Dust bag (material)
M Metabo universal vacuum cleaner
For complete range of accessories, see
www.metabo.com or the main catalogue.
Repairs to electrical tools must be carried out by
qualified electricians ONLY!
Any Metabo power tool in need of repair can be
sent to one of the addresses listed in the spare
parts list.
Please enclose a description of the fault with the
power tool.
Metabo's packaging can be 100% recycled.
Scrap power tools and accessories contain large
amounts of valuable resources and plastics that
can be recycled.
These instructions are printed on chlorine-free
bleached paper.
Only for EU countries: Never dispose of
power tools in your household waste! In
accordance with European Guideline 2002/
96/EC on used electronic and electric equipment
and its implementation in national legal systems,
used power tools must be collected separately
and handed in for environmentally compatible
recycling.
Explanatory notes on the specifications on page 2.
Changes due to technological progress reserved.
D = Diameter of support plate
P
1
= Nominal power input
P2 = Power output
s
0
= Oscillating frequency at idle speed
s
1
= Oscillating frequency at rated load
S = Oscillating circuit diameter
m = Weight without mains cable
Vibration total value (vector sum of three
directions) determined in accordance with
EN 60745:
a
h
= Vibration emission value
(Surface sanding)
K
h
= Unsafe (vibration)
9 Cleaning, Maintenance
10 Tips and Tricks
11 Accessories
12 Repairs
13 Environmental Protection
14 Technical Specifications
17026722_0308 Sr 356.book Seite 11 Montag, 3. März 2008 11:31 11
12
ENGLISH
ENG
The vibration emission level given in this informa-
tion sheet has been measured in accordance with
a standardised test given in EN 60745 and may be
used to compare one tool with another. It may be
used for a preliminary assessment of exposure.
The declared vibration emission level represents
the main applications of the tool. However if the
tool is used for different applications, with different
accessories or poorly maintained, the vibration
emission may differ. This may significantly
increase the exposure level over the total working
period.
An estimation of the level of exposure to vibration
should also take into account the times when the
tool is switched off or when it is running but not
actually doing the job. This may significantly
reduce the exposure level over the total working
period.
Identify additional safety measures to protect the
operator from the effects of vibration such as:
maintain the tool and the accessories, keep the
hands warm, organisation of work patterns.
Typical A-effective perceived sound levels:
L
pA
= Sound pressure level
L
WA
= Acoustic power level
K
pA
, K
WA
= Unsafe (noise level)
During operation the noise level can exceed
85 dB(A).
Wear ear protectors!
Measured values determined in conformity with
EN 60745.
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
17026722_0308 Sr 356.book Seite 12 Montag, 3. März 2008 11:31 11
Metabowerke GmbH,
72622 Nürtingen, Germany
www.metabo.com
17026722_0308 Sr 356.book Seite 61 Montag, 3. März 2008 11:31 11
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64

Metabo SR 356 Operating instructions

Type
Operating instructions
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI