Rangemaster Raindrop Splashback User guide

Brand: Rangemaster

Model: Raindrop Splashback

Type: User guide

This manual is also suitable for

F103920-02

Fitting

Please read all of this instruction before

installing the splashback.

The manufacture disclaims all liabilities

for any damage or injury caused as a

result of not following this instruction

leaet.

This splashback is designed to t

behind a Rangemaster cooker.

It is made of toughened safety glass –

any localised pressure on the glass may

cause it to shatter.

The wall should be at and clear of any

obstructions.

If it is not, the wall must be made good

before proceeding or be prepared to

pack the splash forward of the wall.

Do not attempt to remove the tape

from the back of the glass – it is there

to retain the glass if it should be

broken.

Do not under any circumstances

attempt to cut or drill into the glass

splashback, as this will cause the glass

to shatter.

Take care, the splashback is heavy and

we recommend at least two people

should t it. Beware of sharp edges.

Before drilling the wall check that

there are no electrical cables or pipe

work in the wall in the xing areas.

The splashback should be tted AFTER

the cooker has been installed and

BEFORE a cookerhood is tted.

To Fit the Splashback

You will need the following equipment

to complete the splashback installation

satisfactorily

• A pencil or marker

• A rule

• A drill

• A 7mm masonry drill

• A cross point screwdriver

• If it is necessary to x to a hollow

construction plaster or partition

wall you will need special plaster

board xing screws or plugs.

In order to t the splashback at the

correct height the cooker must rst be

installed, set to the correct height and

levelled.

Mark the wall behind the cooker at the

ue grille height.

ArtNo.420-0008 Marking the wall Falcon

Move the cooker forward. Measure

down 38mm from the your marks and

draw a line.

ArtNo.420-0001 Splashback: marking the wall

original line at cooker height

line of bottom edge of splashback

38mm

This dimension will position the

splashplate as shown in (1).

DO NOT t the splashback as shown

in (2) – contact with the cooker as it

is moved may shatter the glass.

1 2

Hold the splashback in position with

bottom edge level with the lower line.

ArtNo.420-0004 Holding the splashback to wall

Bottom line

Mark the position of the xing holes on

the wall. The vertically slotted holes in

the splashback are intended for screw

xing.

Glass Splashback

At least 6 screws must be used to hold

the splashback, 3 at the top and 3 at

the bottom.

Remove the splashback and drill the

wall using a 7mm masonry bit. Using

the rawl plugs and screws provided,

screw the splashback in position.

Note: When tting a cookerhood

please refer to the cookerhood

instructions for important tting

dimensions.

The cookerhood should be tted as

shown in (3).

DO NOT t the cookerhood as shown

in (4) as this may shatter the glass.

3 4

F103920-02

Care of your Glass Splashback

Cleaning

NEVER USE PAINT SOLVENTS, WASHING SODA, CAUSTIC CLEANERS,

BIOLOGICAL POWDERS, BLEACH, CHLORINE BASED BLEACH CLEANERS,

COARSE ABRASIVES OR SALT.

The glass surface can normally be cleaned using clean hot water and a liquid

detergent. For any stubborn stains use a nylon scouring pad.

Aerosols can be used but the product MUST be suitable for glass and the

manufacturers instructions MUST be followed.

Rangemaster Raindrop Splashback User guide

Brand: Rangemaster

Model: Raindrop Splashback

Type: User guide

This manual is also suitable for

Download PDF

report

Rangemaster Raindrop Splashback User guide

This manual is also suitable for

Rangemaster Raindrop Splashback User guide

Related papers

Other documents