BabyCam Monitor
www.swannsecurity.com
10. Technical Specifications
Quick Start Guide
FCC WARNING STATEMENT:
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired operation
SW231-FLO
STOP
If this product does not work when you first plug
it in or you have any concerns, don’t take it back
to the store!
Use the Installation Guide / Manual in the pack, or
Visit www.swannsecurity.com/help
for FAQs, troubleshooting hints & more, or
Contact our expert Tech Support Team...
Email - tech@swannsecurity.com
United States 1-800-627-2799
1-877-274-3695
Sun 4pm-12am, Mon-Fri 8am-12am (PDT)*
Australia 1300 138 324
Mon 9am-5pm, Tues-Sat 1am-9am (AET)
New Zealand 0800 479 266
Mon 11am-7pm, Tues-Sat 3am-11am (NZDT)
International +61 3 8412 4610
Mon 9am-5pm, Tues-Sat 1am-9am (AET)
*Hours vary during daylight savings times
has the answers
Monitor
Frequency: 2.4GHz
Transmission Range: 150’ (50m)
Channel: 3 Selectable channels
Antenna: Built-in omni-directional
Display: LTPS-TFT 1.5” LCD Full colour
Dimensions: 3.1 (L) x 1.9 (W) x 4.7 (H)
79.9 x 49 x 119.9 mm
Weight: 5.29 oz (150 grams)
Power: DC 6V or 4 x AAA
Operating temperature: 32°F~104°F (O°C~40°C)
Camera
Frequency: 2.4GHz
Antenna: Built-in omni-directional
Image sensor: 1/3” CMOS image sensor
Effective pixels: NTSC: 510(H) x 492 (V)
CCIR: 628(H) x 582(V)
Lens: f6.0mm, F 1.8
Dimensions: 3.1 (L) x 2 (W) x 4.4 (H) inches
79.5 x 50 x 111 mm
Weight: 3.88 oz (110 grams)
Power: DC 6V
Operating temperature: 32°F~104°F (O°C~40°C)
The BabyCam Monitor includes two colored rings to
chage the appearance of the Flower Camera. Use a
pin or flat sharp edge to remove the current ring if
necessary.
9. Miscellaneous Features
WARNING: Keep camera & monitor out of children’s
reach. Do not place camera in or on any part of the cot.
1. Package Contents 3. Camera Layout
4. Powering the Baby Monitor/Camera
5. Changing Channels on the Camera
7. Troubleshooting
6. Adjusting the Brightness
2. Monitor Layout
Use the included power adapters to power both the
camera and monitor. Both adapters are suitable for
either the camera or monitor.
The monitor also has an option for battery power. The
monitor accepts 4 X AAA batteries (not included). For
long periods of use it is recommended to use the power
adapter to operate the monitor. Remove batteries from
the monitor when storing the unit.
To turn the Monitor on or off, push the On/Off button
on the side of the unit.
To power the Flower Camera, simply plug in the power
adapter to the camera. To turn off, unplug the adapter.
Press the Increase or Decrease Brightness buttons to
adjust image. Hold down the button to until you are
happy with the image and then release.
Q: Why is the monitor screen is black?
A: Make sure the Monitor is plugged in. Push the On/
OFF button. The green LED indicates the unit is on.
Q: Why do I see a fuzzy image?
A: Make sure Flower Camera is plugged in. Next push
the Channel Button on the Monitor until you see image.
Q: I can barely see the FlowerCam on the monitor, how
do I make it more clear?
A: Try changing the Flower Camera channel on the back
of the camera and change the Monitor channel to the
correct channel.
Q: I’ve tried all 3 channels but the image still isn’t clear,
what do I do?
A: If possible move the Monitor closer to the location
of the Flower Camera. Move or turn off all electronic
equipment that may be causing interference such as
microwaves, cordless phones, wireless routers etc. The
best quality image will always appear with few devices
or walls between the Monitor and Flower Camera.
To change camera channels, find the Camera Channel
Switch on the back of the Flower Camera. Moving the
switch will change the channel from 1-3.
To change the monitor channel push the middle Channel
Button on the Monitor. The red LED will indicate the
current channel 1, 2 or 3.
• Camera
• LCD Monitor
• Blue Camera Ring
• Pink Camera Ring
• User’s Manual
• AV Cable
• Power Adapters x 2
LCD Screen
Channel
Button
Infrared
LEDs
Camera
Antenna
Camera Channel
Switch on Back
Changeable
Pink/Blue Ring
Camera
Stand Clip
Bendable
Stem
Volume
Control
Increase
Brightness
A/V Output
Power LED
Speaker
Decrease
Brightness
Camera
Channel LED
On / Off
Button
Power Adapter
Input
Power Adapter
Input
Battery
Compartment
Swann Communications • Toll Free Technical Support: USA - 1-800-627-2799, 1-877-274-3695, Australia - 1300 13 8324 • Email: [email protected]
www.swannsecurity.com
/