Hitachi Living Systems MPH-11RI Operating instructions

Brand
Hitachi Living Systems
Model
MPH-11RI
Type
Operating instructions
Hitachi Living Systems
OPERATING INSTRUCTIONS
Thank you for purchasing Hitachi Living Systems gas table. Please read this operating
instruction manual carefully before using this gas table properly. We hope you are satisfied
with our product.
CONTENTS
AUTOMATIC IGNITION GAS TABLE
MPH-11RI
AUTOMATIC IGNITION GAS TABLE
MPH-11RI
n NAME OF PARTS
INSTALLATION OF GAS TABLE and
HOW TO USE
...............................................1
........ 3
n
n
n
..............................................2
.......................................
..............................................4
SPECIAL CAUTIONS AND SPECIFICATIONS
PREPARING THE UNIT FOR USE,
MAINTENANCE AND CARE and TROUBLESHOOTING
NAME OF PARTSNAME OF PARTS
1
Pan SupportPan Support
Burner HeadBurner Head
Top PlateTop Plate
Rubber LegRubber Leg
Body
Ignition Control KnobIgnition Control Knob
Figure 1Figure 1
press
M
A
X
MAX
OFF
Hitachi Living SystemsHitachi
Living
Systems
ONON
MPH11-31Ex01
1. Use only Liquefied Petroleum (LP) gas.
2. Use this gas table only for cooking. Never
use the gas table to dry clothes, and etc.
3. Do not use any small cooking utensil that may cover
the burner flame and thereby extinguish it.
4. Do not use any large cooking utensil which covers the
entire surface of the gas table.
5. Place the gas table in an area with sufficient ventilation.
SPECIFICATIONS
6. If the gas table is used for a long time in a closed space,
oxygen in the air becomes deficient, and there is a danger of
carbon monoxide poisoning due to incomplete combustion.
7. Use only rubber hoses. Do not use vinyl hoses. Vinyl is
not heat resistant and has poor elasticity.
8. When turning on a burner, make sure that the flame
catches completely. Also, make sure that flame is fully
extinguished when you turn off the unit. Even during use,
make sure the flame is burning normally.
9. Do not use a worn-out rubber hose. Old hoses are not
sufficiently elastic, and cracks
due to use may result in gas
leaks. Immediately replace
rubber hose when it gets
damaged or cracked.
10. Trivet, top plate and other parts become hot during
use. Therefore, touch no part of the gas table except the
ON/OFF knobs.
11.Take note that no boiling water should spill onto the gas
table’s top surface.
12. If you notice gas leakage, stop using the gas table at
once, close the gas stopcock, and open all windows and
doors to allow the gas to escape.
13. In case of a gas leak, NEVER turn on the gas table, or
turn on or off ventilation fan or any other electric
appliances. The gas may catch fire and cause an
explosion.
14. Do not leave the gas table unattended when on. After
use, never fail to turn the ON/OFF knob to the “OFF”
position and to switch off the gas stopcock. Also, make
sure that the flame is completely extinguished. When you
go out or when you go to sleep, always make sure to switch
off the gas stopcock.
The appropriate gas pressure range for this product is
25 0 ~350 mm H O
2
OFF
Small
Max
ONON
O
FF
OFF
SPECIAL CAUTIONSSPECIAL CAUTIONS
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
2
External dimensions
(H)x(W)x(D) : mm
: inch
Gas consumption
Kcal/h (PB)
Gas pressure
300 mm WC
MPH-11RI
146x280x396
5.7x11x15.6
2.0
Piezo-electric
2350
1. Installation of rubber legs.
Attach the rubber legs to the table by screwing them into the
openings on the table bottom.
2. Installation of ON/OFF knobs, burner heads and trivet &
trays.
Place the ON/OFF knob on the gas cook axis and push it
firmly inwards. Set the burner head on the burn body, then
place the trivet & trays on the top plate.
Ignition (ON/OFF)
knob
Trivet &tray
1. Install the gas table securing a minimum clearance of
15 cm from the side/back wall and 100cm from the
ceiling.
2. Connect the rubber hose to the gas cylinder
3. Make sure there is no dust on the gas inlet pipe and fit
the rubber hose over the gas inlet pipe, making sure the
end of the hose reaches the line as shown. Fasten the
hose securely with a hose clamp.
Gas inlet pipe
Rubber hose
Hose clamp
l Do not route the rubber hose under
the gas table.
Do not place any objects that may
easily be blown away by the wind on
the gas table.
l
l Never use one single rubber hose
for two gas tables.
Keep away flammable material/
liquid from the gas table.
l
Make sure that all knobs of the gas table are at the “OFF” position, and open fully the gas stopcock of gas cylinder.
1. Ignition and Flame Adjustment
Push the knob fully and turn counterclockwise to “ON”.
Flame is adjustable between “ON” and “OFF” position
by turning the knob slowly.
Push fully
Small
Max
ON
OFF
Igniting the burner for the first time may be difficult because of air trapped in the gas hose. Repeat the ignition
procedure several times until the air is purged and the burner is ignited.
2. Extinction
Turn the ignition knob to the “OFF” position. In this position, no gas is supplied and the flame goes out.
PREPARING THE UNIT FOR USEPREPARING THE UNIT FOR USE
INSTALLATION OF GAS TABLEINSTALLATION OF GAS TABLE
Burner head
Rubber leg
Note
HOW TO USEHOW TO USE
Note
Note
Turn counter-clockwise
3
p
r
e
s
s
press
M
A
X
O
F
F
OFF
H
itac
hi Living Sy
stem
s
Hitachi
Living
Systems
15 cm. 15 cm.
100 cm.
Figure 2Figure 2
O
N
ON
Figure 2Figure 2
Figure 2Figure 2
Note
MAINTENANCE AND CARE
Note
TROUBLESHOOTING
When fire extinction sound is loud, adjust air supply by turning Damper upward or downward.
If the burner and its surrounding parts get too dirty, incomplete combustion may result. Therefore, clean these
parts carefully.
3. Air-Adjustment
Adjust the opening for air intake in order to get good combustion by moving the damper as indicated.
2. Cleaning of the trivet & tray
Always keep the trivet & tray clean.
3. .Cleaning of the electrodes of the igniter If the
electrodes are soiled, clean them with a dry cloth
as dust adhering these parts may prevent a good
ignition.
Note
Make sure that the burner body, burner head, trivet and other parts are set properly after cleaning.
If trouble occurs, fix it referring to the following table. If the problem still remains, or in case a serious malfunction, or if you
are in doubt, take the table to the retailer from which you bought the unit, without trying to repair it yourself.
Trouble
Cause Remedial measure
Does not ignite
Smell of gas
Flame makes loud
cracking sound while
burning
- Main gas stopcock is not open.
- Air remains in the gas piping.
- Dirty electrode or insulator.
- Bent or crushed rubber hose.
- Make sure the ignition knob is at “OFF” position, then
open the main gas cock fully.
- Repeat igniting operation until all air in the piping is
completely purged.
- Clean it with a dry rag.
- Straighten gas hose.
- Cracks or holes in the rubber hose.
- Rubber hose not connected well.
- Failure or the gas table cock.
- Replace it with a new one.
- Connect gas hose surely.
- Ask the store for repairs.
- Air supply is not properly adjusted.
- Flame outlet of burner is closed.
- Burner is not fitted properly.
- Nozzle is clogged.
- Adjust it properly.
- Clean the clogged part.
- Fix burner body properly.
- Ask the store for repairs.
4
Figure 5Figure 5
Figure 3Figure 3
1. When the combustion state gets deteriorated
due to boiling over, clean the holes of burner head
as indicated in order to recover optimum flames .
Make sure that all the parts are fitted properly
before use.
Installation: Vacant position of burner head
must be fixed completely into the pad of ventury.
When returning the cleaned burner head to the
burner, make sure to set it correctly.
1
2
3
4
1. Burner head
2. Vacant position of burner
head
3. Ventury
4.Pad of ventury
Hitachi Living Systems
Damper location
Good combustion
Short supply of air Oversupply of air Oversupply of air
Opening for air intake
Damper
Wire
Optimum flame
Figure 4Figure 4
Figure 4Figure 4
Figure 5Figure 5
Figure 3Figure 3
OK
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Hitachi Living Systems MPH-11RI Operating instructions

Brand
Hitachi Living Systems
Model
MPH-11RI
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents