Mitsubishi Electric CM33-TL User manual

COMPUTER PRODUCTSCOMPUTER PRODUCTS

COMPUTER PRODUCTS

CM33-TL

System Board

User Manual

(Manual Part Number MAN-0CM33-001)

WARNING!

Programmable control devices such as MEAU’s Industrial Computers must not be used as stand-alone protec-

tion in any application. Unless proper safeguards are used, unwanted start-ups could result in equipment

damage or personal injury. The operator must be made aware of this hazard and appropriate precautions must

be taken.

In addition, consideration must be given to the use of an emergency stop function that is independent of the

programmable controller.

The diagrams and examples in this user manual are included for illustrative purposes only. The manufacturer

cannot assume responsibility or liability for actual use based on the diagrams and examples.

Trademarks

This publication may contain references to products produced and/or offered by other companies. The

product and company names may be trademarked and are the sole property of their respective owners.

MEAU and/or AVG Automation disclaims any proprietary interest in the marks and names of others.

Manual P/N MAN-0CM33-001

Designed, and Manufactured specifically for Mitsubishi Electric Automation, Inc., by AVG

Mitsubishi Electric Automation, Inc. (MEAU)

500 Corporate Woods Parkway, Vernon Hills, IL 60061

Phone: (847) 478-2100 • Fax: (847) 478-2253 • www.meauic.com

AVG Automation

Mitsubishi Approved IC Service Center

4140 Utica Ridge Rd. • Bettendorf, IA 52722-1327

Phone: 1-563-359-7501 • Fax: 1-563-359-9094 • www.avg.net

No part of this manual shall be copied, reproduced, or transmitted in any way without the prior written

consent of AVG Automation. AVG Automation retains the exclusive rights to all information included in this

document.

i

MAN-0CM33-001 MC Series Computer Products

Warning/Caution/Copyright Information .................................... inside cover

Contents ........................................................................................ i

CHAPTER 1 INTRODUCTION

Manual Organization............................................................................. 1

Introduction 2

Safety Precautions ................................................................................ 2

Technical Support ................................................................................. 2

Features and Specifications ................................................................. 3

CHAPTER 2 HARDWARE INSTALLATION

CM33-TL System Board Layout ........................................................... 7

System Memory .................................................................................... 8

Jumpers ....................................................................................... 9

Jumper Settings for Clearing the CMOS Data .............................. 9

Jumper Settings for Selecting the USB Power............................ 10

Ports and Connectors ......................................................................... 11

PS/2 Mouse and PS/2 Keyboard Ports ....................................... 11

Parallel Port .................................................................................. 12

Universal Serial Bus Port ............................................................. 13

VGA Port ..................................................................................... 14

RJ45 Fast-Ethernet Port (CM33-TL) ........................................... 15

CHAPTER 3 AWARD BIOS SETUP UTILITY

Basic Input/Output System ................................................................. 17

Standard CMOS Features .................................................................. 17

Advanced BIOS Features ................................................................... 20

Advanced Chipset Features ............................................................... 24

Integrated Peripherals ........................................................................ 26

Power Management Setup ................................................................. 29

PnP/PCI Configuration ....................................................................... 32

PC Health Status ................................................................................ 34

Frequency/Voltage Control ................................................................. 36

Updating the BIOS .............................................................................. 38

CHAPTER 4 SUPPORTED SOFTWARE

VIA Hardware Monitor ......................................................................... 39

Onboard LAN Drivers for Windows .................................................... 39

Graphics Drivers ................................................................................. 39

Error/Improvement Report ..................................................................... 41

APPENDIX A SYSTEM ERROR MESSAGES

System Error Messages ................................................................... A-1

CONTENTS

ii MC Series Computer Products MAN-0CM33-001

CONTENTS

APPENDIX B TROUBLESHOOTING

Troubleshooting Checklist ................................................................. B-1

Monitor/Display .................................................................................. B-1

Power Supply ..................................................................................... B-2

Floppy Drive ....................................................................................... B-2

Hard Drive ................................................................................... B-2

Parallel Port ................................................................................... B-2

Serial Port ................................................................................... B-3

Keyboard ................................................................................... B-3

System Board ................................................................................... B-3

1

MAN-0CM33-001 MC Series Computer Products

INTRODUCTION 1

The table, below, provides an overall description of the topics covered within this manual.

Manual Organization

Introduction This chapter introduces you to the background of this

manual, and the features and specifications for this

system board. The final page of this chapter will

indicate how to avoid damaging the Embedded CPU

Card.

Hardware

Configuration

This chapter outlines the component locations and their

functions. You will be shown how to install a DIM

Module and set Jumpers to configure the CPU to meet

your own needs.

Award BIOS

Setup Utility

This chapter describes how to set up the BIOS

configurations.

Supported

Software

This chapter discusses the software (utilities, drivers)

that was provided with your computer.

Chapters

Appendix A

System Error

Messages

This appendix provides you with System Error Mes-

sages that may occur during use, what may prompt

these messages, and corrective action.

Appendix B

Troubleshooting

This appendix outlines the errors that may occur when

you operate the system. It also provides suggestions for

problem resolution.

B

A

4

3

2

1

2MC Series Computer Products MAN-0CM33-001

1 INTRODUCTION

Introduction

Mitsubishi Electric Automation MEAU now offers the MC Series Industrial Com-

puter products to comply with the demands of most every factory application.

The MEAU brand of computer’s offer the extreme reliability, and feature sets

that OEM’s, and end users have come to expect with Mitsubishi Electric Auto-

mation products.

The MEAU MC Series Industrial Computer line is designed for harsh plant

environments, with rugged materials to withstand the daily riggers of opera-

tion. Designed with component longevity in mind, and to accommodate the

fast rate of change in computer technology, our computer products employ

competent component performance ranges for industrial applications. This

ensures the long term acquisition of components, and repeatability of product,

along with true forward/backward compatibility.

In keeping with these performance demands, the CM33-TL Embedded Sys-

tem Board has been installed in your MC400 Series Industrial Node Computer.

The CM33-TL is a Micro ATX Style CPU Card for a Single Intel® Pentium® III

Processor in a 370-pin socket.

This manual provides you with the information you need to configure the CM33-

TL and get your MC400 Series Computer up and running in accordance with

your application requirements.

Safety Precautions

Follow the precautions below to avoid damaging your system:

1. Keep your system away from static electricity at all times.

2. Prevent electric shock. Don‘t touch any components of this card when

the card is powered on. Always disconnect power when the system is

not in use.

3. Disconnect power when you change any hardware device. For

instance, when you connect a jumper or install any cards, a surge of

power may damage the electronic components or the whole system.

Technical Support

If you are having difficulty with a particular aspect of installation or setup, tech-

nical support is available at 1-800-950-7781 (Auto Attendant, Option 4) or

visit our website at www.meauic.com.

3

MAN-0CM33-001 MC Series Computer Products

INTRODUCTION 1

Features and Specifications

Features

Processor: Pentium® III

FCPGA2 133MHz FSB (1.13GHz-1.26GHz on 0.13 µ)

FCPGA 133 MHz FSB (5.33EB-1GHz)

System Memory:

•Supports up to 1 GB using VCM (Virtual Channel Memory)

or PC SDRAM DIMM (unbuffered or registered)

• Two 168-pin DIMM sockets

• Uses x64 PC SDRAM, 3.3V

PC-133 SDRAM DIMM for 133 MHz FSB processors

Note: If you are using more than one DIMM, ensure that you insert the same

type of DIMMs into the DIMM sockets. Using different types (VCM or PC

SDRAM) of DIMMs may cause problems.

Expansion Slots

The system board is equipped with 3 dedicated PCI slots.

Onboard Graphics Features

•Integrated rCADE3D 2D/3D/Video accelerator

— Shares 8MB of the system memory

— Optimized Shared Memory Architecture (SMA)

— High quality DVD video playback

•3D rendering features

— 32-bit true color rendering

— MPEG-2 video textures

4MC Series Computer Products MAN-0CM33-001

1 INTRODUCTION

•2D hardware acceleration features

•Motion video architecture

•Software drivers

— Windows® 98/98SE/ME/2000/XP

— Windows NT® 4.0

Onboard LAN Features

•Uses Realtek RTL8100 fast ethernet controller

•Integrated IEEE 802.3 10BASE-T and 100BASE-TX compatible

PHY

•32-bit PCI master interface

•Integrated power management functions

•Full duplex support at both 10 and 100 Mbps

•Supports IEEE 802.3µ auto-negotiation

•Supports wire for management

ATX Double Deck Ports (PC 99 color-coded connectors)

•Two USB ports

•One RJ45 LAN port

•One NS16C550A-compatible DB-9 serial port

•One DB-15 VGA port

•One DB-25 Parallel port

•One mini-DIN-6 PS/2 mouse port

•One mini-DIN-6 PS/2 keyboard port

Connectors

•Two IDE connectors

•One floppy drive interface supports up to two 2.88MB floppy drives

•One ATX power supply

•One Wake-On-LAN connector

•One Wake-On-Ring connector

•CPU fan and chassis fan connectors

PCI Bus Master IDE Controller

•Two PCI IDE interfaces support up to four IDE devices

•supports ATA/33, ATA/66 and ATA/100 hard drives

•PIO Mode 3 and Mode 4 Enhanced IDE (data transfer rate up to

16.6 MB/sec.)

5

MAN-0CM33-001 MC Series Computer Products

INTRODUCTION 1

•Bus mastering reduces CPU utilization during disk transfer

•Supports ATAPI CD-ROM, LS-120 and ZIP

USB Ports

The system board supports 2 USB ports. Two onboard USB ports are located

at the ATX double deck ports of the board. USB allow data exchange between

your computer and a wide range of simultaneously accessible external Plug

and Play peripherals.

BIOS

•Award BIOS, Windows® 95/98/2000/ME/XP Plug and Play

compatible

•Flash EPROM for easy BIOS updates

•Supports DMI 2.0 function

•2 Mbit flash memory

Desktop Management Interface (DMI)

The system board comes with a DMI 2.0 built into the BIOS. The DMI utility in

the BIOS automatically records various information about your system con-

figuration and stores this information in the DMI pool, which is a part of the

system board’s Plug and Play BIOS. DMI, along with the appropriately net-

worked software, is designed to make inventory, maintenance and trouble-

shooting of computer systems easier. Refer to Chapter 4 for instructions on

using the DMI utility.

System Health Monitor Functions

The system board is capable of monitoring the following “system health” con-

ditions.

•Monitor CPU/system temperature and overheat alarm

•Monitors VCORE/3.3V/5V/12V/2.5V voltages and failure alarm

•Monitors CPU/chassis fan speed and failure alarm

•Automatic CPU and chassis fans on/off control

•Read back capability that displays temperature, voltage and fan

speed

Refer to the “PC Health Status” section in chapter 3 and the “VIA Hardware

Monitor” section in chapter 4 for more information.

Automatic CPU/Chassis Fan Off

The CPU and chassis fans will automatically turn off once the system enters

the Suspend mode.

6MC Series Computer Products MAN-0CM33-001

1 INTRODUCTION

Dual Function Power Button

Depending on the setting in the “Soft-Off by PWRBTN” field of the Power Man-

agement Setup, this switch will allow the system to enter the Soft-Off or Sus-

pend Mode.

AC Power Failure Recovery

When power returns after an AC power failure, you may choose to either power-

on the system manually, let the system power-on automatically or return to the

state where you left off before power failure occurred. Refer to “PWR Lost

Resume State” in the Power Management Setup section in Chapter 3 for more

information.

Virus Protection

Most viruses today destroy data stored in hard drives, The system board is

designed to protect the boot sector and partition table of your hard disk drive.

7

MAN-0CM33-001 MC Series Computer Products

2 HARDWARE INSTALLATION

Hardware Installation

CM33-TL System Board Layout

8MC Series Computer Products MAN-0CM33-001

2 HARDWARE INSTALLATION

WARNING: Electrostatic discharge (ESD) can damage your system board,

processor, disk drives, add-in boards, and other components. Perform

the upgrade instruction procedures described at an ESD workstation only.

If such a station is not available, you can provide some ESD protection by

wearing an antistatic wrist strap and attaching it to a metal part of the

system chassis. If a wrist strap is unavailable, establish and maintain

contact with the system chassis throughout any procedures requiring

ESD protection.

System Memory

The system board is equipped with two 168-pin DIMM (Dual In-line Memory

Module) sockets that support VCM or PC SDRAM DIMM. PC SDRAM (Syn-

chronous Dynamic Random Access Memory) uses a fast memory interface

technology that includes using the clock on the chip to synchronize with the

CPU clock so that the timing of the memory chips and the timing of the CPU

are synchronized. This saves time during transmission of data, subsequently

increasing system performance.

Refer to Chapter 1 (System Memory section)

for detailed specification of the memory sup-

ported by the system board.

Installing the DIM Module

A DIM Module simply snaps into a DIMM

socket on the system board. Pin 1 of the DIM

module must correspond with Pin 1 of the

socket.

1. Pull the “tabs,” located at the end of

the socket, to the side

2. Position the DIMM above the socket with the “notches” in the module

aligned with the “keys” on the socket.

3. Seat the module vertically into the socket. Make sure it is completely

seated. The tabs will hold the DIMM in place.

9

MAN-0CM33-001 MC Series Computer Products

2 HARDWARE INSTALLATION

Jumper Settings for Clearing the

CMOS Data

If you encounter the following: a)

CMOS data becomes corrupted; b)

Supervisor or User Password is for-

gotten; c) Unable to boot-up the com-

puter system because the

processor’s bus clock was incorrectly

set in the BIOS, you can reconfigure

the system with the default values

stored in the ROM BIOS.

To load the default values stored in

the ROM BIOS, please follow the

steps below.

1. Power-off the system and

unplug the power cord.

2. Set JP3 pins 2 and 3 to ON.

Wait for a few seconds and

set JP3 back to its default

setting, pins 1 and 2 ON.

3. Plug the power cord and power-on the system.

If your reasons for clearing the CMOS data is due to incorrect setting

of the processor’s bus clock in the BIOS, proceed to step 4.

4. After powering-on the system, press <Del> to enter the main menu of

the BIOS.

5. Select the “Frequency/Voltage Control” submenu and press <Enter>.

6. Set the “Clock By Slight Adjust” field to its default setting or an

appropriate bus clock. Refer to “Clock by Slight Adjust” in the

“Frequency/Voltage Control” section in Chapter 3 for more informa-

tion.

7. Press <Esc> to return to the main menu of the BIOS setup utility.

Select “save & Exit Setup” and press <Enter>.

8. Type <Y> and press <Enter>.

Clear CMOS Data - jumper JP3

JUMPERS

10 MC Series Computer Products MAN-0CM33-001

2 HARDWARE INSTALLATION

Jumper Settings for Selecting the USB Power

Power Select for USB 1 and 2 (JP1) and

This jumper is used to select the power for the USB devices that are con-

nected to the USB ports.

11

MAN-0CM33-001 MC Series Computer Products

2 HARDWARE INSTALLATION

PS/2 Mouse and PS/2 Keyboard Ports

The system board is equipped with onboard PS/2 Mouse (Green) and PS/2

Keyboard (Purple) ports — both at location J1 of the ATX double deck ports of

the system board. The PS/2 mouse port uses IRQ12. If a mouse is not con-

nected to this port, the system will reserve IRQ12 for other expansion cards.

Caution: Make sure to turn off your computer prior to connecting or dis-

connecting a mouse or keyboard. Failure to do so may damage the sys-

tem board.

PORTS AND CONNECTORS

12 MC Series Computer Products MAN-0CM33-001

2 HARDWARE INSTALLATION

Parallel Port

The system board has a standard parallel port (J9 - Burgundy) located at the

ATX double deck ports of the board for interfacing your PC to a parallel printer.

It supports Normal, ECP and EPP modes. You can set the port’s mode in the

Integrated Peripherals submenu of the BIOS.

Setting Function

Normal Allows normal speed operation but in

one direction only.

ECP (Extended

Capabilities Port) Allows parallel port to operate in bidirectional mode

and at a speed faster than the SPP’s data

transfer rate

EPP (Enhanced Allows bidirectional parallel port operation at

Parallel Port) maximum speed.

13

MAN-0CM33-001 MC Series Computer Products

2 HARDWARE INSTALLATION

Universal Serial Bus Ports

The system board supports 2 USB ports. USB allows data exchange between

your computer and a wide range of simultaneously accessible external Plug

and Play peripherals. You must have the proper drivers installed in your oper-

ating system to use the USB ports. Refer to your operating system’s manual

or documentation.

Two onboard USB ports (J8 - Black) are located at the ATX double deck ports

of the board.

14 MC Series Computer Products MAN-0CM33-001

2 HARDWARE INSTALLATION

VGA Port

The system board can only be used with an analog video monitor. Connect

the monitor’s 15-pin D-shell cable connector to the VGA port (J3 - Blue) lo-

cated at the ATX double deck ports of the board. Some monitors have a switch

that chooses between analog and TTL (or digital) operation. If your monitor

has such a switch, set it for analog.

15

MAN-0CM33-001 MC Series Computer Products

2 HARDWARE INSTALLATION

RJ45 Fast-Ethernet Port (CM33-TL)

The system board is equipped with an onboard RJ45 fast-ethernet LAN port at

location J8 of the ATX double deck ports. It allows the system board to con-

nect to a local area network by means of a network hub.

16 MC Series Computer Products MAN-0CM33-001

2 HARDWARE INSTALLATION

This page intentionally left blank.

Page is loading ...

Mitsubishi Electric CM33-TL User manual

Mitsubishi Electric CM33-TL User manual

Other documents