Prince Castle 233-71 Operating instructions

Brand: Prince Castle

Model: 233-71

Type: Operating instructions

OPERATING

INSTRUCTIONS

Grill Wiper

Model No. 233-71

355 East Kehoe Blvd. z Carol Stream, IL 60188

Tel: (630) 462-8800 z Fax: (630) 462-1460

Toll Free: 1-800-PCASTLE

Printed in 2001

Prince Castle Inc.

233-511

LIMITED WARRANTY

This product is warranted to be free from defects in

material and/or workmanship for a period of one (1)

years from date of original installation, not to ex-

ceed 30 months from date of shipment from our

factory.

Any component which proves to be faulty in material

and/or workmanship will be replaced or repaired (at

the option of Prince Castle, Inc.) without cost to the

customer for parts or labor.

This warranty is subject to the following exceptions/

conditions:

z Any use of non-genuine Prince Castle replace-

ment spare parts voids this warranty. All genu-

ine Prince Castle replacement spare parts are

warranted for ninety (90) days from date of pur-

chase.

z Damage caused by carelessness, neglect, and/

or abuse (e.g., dropping, tampering or altering

parts), equipment damaged in shipment, by fire,

flood or an act of God is not covered under this

warranty.

Prince Castle’s 233-71 Grill Wiper is perfect for

removing excess grease from the griddle or Teflon©

coverings on topside cookers. The silicone rubber

blade prevents damage of surfaces, and is reversible

for long-life. Designed to withstand temperatures up

to 450° F (232° C), the grill wiper features a heat

resistant handle for operator safety.

After you have removed the Grill Wiper from the

carton, inspect the unit for signs of damage. If there

is damage to the unit:

z Notify carrier within 24 hours after delivery.

z Save carton and packing materials for inspection

purposes.

z Contact the Prince Castle Customer Service

Department at 1-800-722-7853 to arrange for

a replacement to be sent.

Verify that all parts have been received.

WIPER BLADE ROTATION OR

REPLACEMENT PROCEDURE

The model number 233-71 is designed to tightly retain

the wiper strip during use and to be disassembled

without tools or small loose fasteners. The following

procedure should be used to rotate the wiper strip to

provide a new edge or to replace it completely.

IMPORTANT: The grill wipers should be rotated on a

daily basis to ensure a longer life.

1. Soften the wiper strip “A” by squeezing the two long

edges together several times. (Soaking in hot

soapy water aids disassembly.) See figure 1.

2. Place grill wiper on table or flat surface, press down

firmly on locking strip “B” and slide sideways.

IMPORTANT: If slide cannot be moved, use pliers to

facilitate disassembly by gripping over tab closest to

the key-hole slot and the nearest locking pin. Squeez-

ing the pliers moves the locking slide so the locking pin

is released through the larger portion of the key-slot.

PARTS LIST

figure 1

3. Remove locking strip “B” to free wiper blade and

rotate and replace as required.;

4. Before reassembling, soften wiper strip “A” by

squeezing the two long edges together several

times. Lubricated underside of locking strip “B”

with shortening.

5. Place wipe strip “A” over locking pins “C”.

Squeeze strip edges together while pressing down

over the pins.

6. Replace locking strip “B” over locking pins, firmly

press down and slide locking strip over pins to the

lock position.

ITEM PART NO. DESCRIPTION

1 233-82 Locking Strip

2 233-86 Wiper Strip (Pkg of 4)

Prince Castle 233-71 Operating instructions

Prince Castle 233-71 Operating instructions

Prince Castle 233-71 Operating instructions

Related papers

Other documents