The Sentry Printer Option aids in management of
your gas risk with the ability to print a variety of
complete reports.
Sentry's preformatted reports provide critical information
for analyzing gas exposure and evaluating system reliabil-
ity. Report selection criteria are user definable. These
reports:
• Help user make better decisions during a gas leak
• Provide history to analyze all exposure events
• Substantiate due diligence in complying with regu-
lations
• Confirm the reliability of the system.
With optional Sentry printer software, preformatted reports
can be printed via the RS232 port on the Sentry connector
panel. Output is either directly from one controller to a
printer or, via the Sentry Master and Subordinate network
system, from several controllers to one printer.
STATUS REPORT
Status Reports show a snapshot of the gas concen-
tration and alarms. The reporting interval is user pro-
grammable from 1 hour to 7 days. The first line indi-
cates the controller ID and date/time. The second
line indicates the sensor number and alarm condition
(“L” for low alarm and “H” for high alarm). The third
line indicates the current concentration and the fourth
line indicates the gas type.
SYSTEM REPORT
The System Report lists all the system parameters
including the software configuration of the system, cali-
bration configuration, printer configuration and configu-
ration for each module: on/off condition, calibration sta-
tus, relay latching configuration, alarm levels, module
type, the controller channel to which it is connected,
and calibration conditions and factors.
Sentry
Printer Option
Sierra Monitor Corp. 1991 Tarob Ct., Milpitas, CA 95035, USA, 408-262-6611, 800-727-4377, FAX: 408-262-9042
Web Site: http://www.sierramonitor.com E-Mail: sales@sierramonitor.com
© 2009 by Sierra Monitor Corporation
The Sentry Printer is a modern, high-speed, quiet, ultra
compact, state-of-the-art printer that can operate as either
a serial or parallel output printer.
This printer utilizes thermal paper
and thus no ink! It has minimal
moving parts, easy maintenance
with self-diagnostics, and easy
paper loading with a clamshell de-
sign. Standard power for the 5301-
10 is 12-24 VDC. An optional
power supply is available to en-
able an operator to use 120VAC
power..
Printer (5301-10)
5301-10 Serial/Parallel Compact Printer
SPL69207 120V Power Supply
SPL69205 Thermal Paper for Compact Printer
DIAGNOSTIC REPORT
The Diagnostic Report lists the critical voltage conditions
for each module and can be selected to print periodically
at intervals from 1 to 90 minutes.
--------------------------------
<STATUS REPORT>
ID:A STATUS = 01 HOUR 12/17 15:00
1 2 3 4 5 6 7 8
03 04 20.9 20.9 08 08 18 19
H2S COMB OXY OXY COMB COMB COMB COMB
---------------------------------
<STATUS REPORT>
ID:A STATUS = 01 HOUR 12/17 16:00
1L 2 3 4 5 6 7 8
03 04 20.9 20.9 08 09 08 08
H2S COMB OXY OXY COMB COMB COMB COMB
---------------------------------
<STATUS REPORT>
ID:A STATUS = 01 HOUR 12/17 17:00
1 2 3 4 5 6 7 8
13 04 20.9 20.9 08 09 22 19
H2S COMB OXY OXY COMB COMB COMB COMB
--------------------------------------
<STATUS REPORT>
ID:A STATUS = 01 HOUR 12/17 18:00
1H 2 3L 4 5 6 7L 8
23 04 19.5 20.9 08 06 40 19
H2S COMB OXY OXY COMB COMB COMB COMB
---------------------------------
<SYSTEM REPORT>
ID:A USER # = 1 12/17 15:08
M5000 VER:4.19
PN 8C
CALIBRATION CONFIGURATION:
LC: OFF CAL FREQ= 90 DAYS
H2S = 20 CAL DUE = 88 DAYS
COMB= 60 CAL DUE = 89 DAYS <SEL>
PRINTER CONFIGURATION:
PRINTER: ON STATUS = 07 DAYS HIST:YES
H2S : MIN. CONC. = 05 CHANGE = 03
COMB: MIN. CONC. = 08 CHANGE = 13
MODULE CONFIGURATION :
MODULE 1 IS ON H2S CHANNEL=1
LA= 10 NLATCH HA= 20 LATCH
FACTOR(S)= 100 150 200
MODULE 2 IS ON COMB CHANNEL 2
PRINTER
ACCESSORIES
KEY EVENT REPORT
When any module reading exceeds a preset minimum
level an Event Report is generated. After the sensor is
above the minimum level, any change greater than a pre-
set change concentration will cause another Event Re-
port to print. The Event Report prints all module num-
bers and their present reading. This concise record pro-
vides information for better decision-making before an
alarm level is reached.
CALIBRATION REPORT
The Calibration Report prints automatically upon comple-
tion of calibration. The report indicates which gas type
was calibrated, the gas concentration and the planned
frequency of calibration. For each module the report lists
the percent change during calibration, the peak concen-
tration and the zero and span sensor voltages. Module
sensitivity is also checked. Proper sensitivity requires
that the voltage difference obtained in air (1
st
voltage) and
with span gas (2
nd
voltage) is sufficient to get adequate
resolution.
HISTORY REPORT
The History Report lists the last time each significant
event has occurred. This includes system power inter-
ruption, history reset, alarm and concentration informa-
tion for each sensor, calibration time for each sensor and
an error log. A History Report can be printed each time a
programmed Status Report is printed. These records are
useful in establishing the presence of gas during the pe-
riod and documenting the company’s due diligence in its
gas monitoring efforts.
WARM START REPORT
At any time the system is warm started due to a power
failure, a report is generated to show the system soft-
ware configuration, the result of an internal diagnostic
sequence and the power down and power up date and
times.
----------------------------------------
ID:A <KEY EVENT REPORT> 12/17 14:27
1 2 3 4 5 6 7 8
05 03 23 29 07 02 01 02
----------------------------------------
ID:A <KEY EVENT REPORT> 12/17 14:35
1 2 3 4 5 6 7 8
07 03 23 25 08 02 01 02
----------------------------------------
ID:A <KEY EVENT REPORT> 12/17 14:37
1L 2 3 4 5L 6 7 8
11 03 23 25 12 02 02 03
----------------------------------------
ID:A <KEY EVENT REPORT> 12/17 14:40
1H 2 3 4 5L 6 7 8
21 04 23 24 12 03 09 02
----------------------------------------
ID:A <KEY EVENT REPORT> 12/17 14:45
1H 2 3 4 5L 6 7L 8
35 04 22 24 13 03 20 02
----------------------------------------
ID:A <KEY EVENT REPORT> 12/17 14:56
1H 2 3 4 5 6 7L 8
----------------------------
<CALIBRATION REPORT>
ID:A USER # =0 12/18 10:03
GAS TYPE : COMB
CALIB CONC= 60
CAL FREQ= 90 DAYS
GLOBAL CALIB: OFF
>MODULE # = 2
% CHANGE = +01 %FS
PEAK CONC. = 61
1ST VOLTAGE = +0.073
2ND VOLTAGE = +0.810
>MODULE # = 3
% CHANGE = -15 %FS
PEAK CONC. = 45
1ST VOLTAGE = +1.649
2ND VOLTAGE = +1.395
>MODULE # = 4
LOW SENSIVITY
% CHANGE = +01 %FS
PEAK CONC. = 61
1ST VOLTAGE = +0.073
2ND VOLTAGE = +0.816
----------------------------------------
<HISTORY REPORT>
ID:A USER # =1 12/17 15:08
HISTORY RESET AT: 02/01 10:59
POWER DOWN AT:12/17 13:34
POWER UP AT:12/17 13:44
MODULE 1 PPM H2S
LOW ALARM 12/13 05:07
HIGH ALARM 12/17 15:07
LOWEST CONC = 00 12/16 10:59
HIGHEST CONC = 23 12/17 15:07
LAST CALIBRATED :02/15 14:33
MODULE 2 %LEL COMB
LOW ALARM 12/10 12:08
HIGH ALARM 00/00 00:00
LOWEST CONC = 00 12/16 11:36
HIGHEST CONC = 45 12/10 12:35
LAST CALIBRATED :02/16 11:35
MODULE 3 %LEL COMB
LOW ALARM 12/10 11:57
HIGH ALARM 12/10 12:20
LOWEST CONC = 00 03/16 10:59
Sierra Monitor Corp. 1991 Tarob Ct., Milpitas, CA 95035, USA, 408-262-6611, 800-727-4377, FAX: 408-262-9042
Web Site: http://www.sierramonitor.com E-Mail: sales@sierramonitor.com
© 2009 by Sierra Monitor Corporation
Sentry Printer
SPECIFICATIONS for Printer 5301-10
PRINTING: Direct Thermal
CHARACTERS per LINE: 16 cpi, 24 cpi, 32 cpi, 42 cpi
CHARACTER SIZE 9x24 dots, 12x24 dots, 16x24 dots,
24x24 dots
RESOLUTION 203 dpi, 8 dots/mm
PRINT WIDTH 2-inch (48 mm)
PRINTING SPEED 50 mm/sec
INTERFACES
Sentry Controller Serial RS232
Sentry Commander Parallel
FieldServer Serial RS232
DIMENSIONS 3.2 x 3.95 x 2.2 inches (80 x 75 x 55
mm)
PAPER Thermal Roll 57 mm wide; 40 mm
diameter, spproximately 20m long
POWER 12V-24V DC
OPERATIING TEMP. 32 - 113
o
F (0-45
o
C)
-
1
-
2
Sierra Monitor Corporation SPL69207 User manual
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Sierra Monitor Corporation TR-001 User manual
-
-
-
-
-
-
-
-
-
Sierra Monitor Corporation IT Series User manual
Other documents
-
SMC SP400 Owner's manual
-
Sentry Industries 5000 User manual
-
HP SENTRY User manual
-
Tektronix Sentry Edge III User manual
-
Sierra Monitor SMC 3200/3300 UV/IR Wet Bench Flame Detector User manual
-
-
-
FieldServer FS-8700-103 User manual
-
-