P/No.: MFL62883403
MODEL : PSF1032A
User Manual
IMPORTANT
• Please read this installation manual completely
before installing the product.
• Installation work must be performed in
accordance with the national wiring standards by
authorized personnel only.
• Please retain this installation manual for future
reference after reading it thoroughly.
What is PLS?
Plasma Lighting System
PLS is a non-electrode lighting device using the new concept
of plasma illumination by microwave.
PLS is an economic lamp with high efficiency and long life
span.
- Power consumption and maintenance cost are lower compared to the
existing lighting (Based on number of installations)
- With the ballast internally installed, there is no need to separately
purchase the ballast.
Optimal lighting environment
- PLS provides optimal lighting environment with high illumination even for
the wide area. (Refer to the following distribution curve of luminous
intensity.
- The level of light fading after long use is minimal.
Nature friendly lighting
- Simulates natural and high color rendering lighting.
- Minimizes radiation of ultraviolet and infrared ray.
- No environmentally hazardous material (Mercury, lead, cadmium etc.)
Features
- LEGEND (D-PLANES)
Distribution curve data of luminous intensity
(Based on average beam angle)
- CONE LUX LEVELS
2
3
Contents
Safety precaution
4~7
Installation criteria and example
10~12
Installation method
8
Check before requesting for service
13
Component and name
9
Installation and power connection 4-5
Using and cleaning 6-7
Product specification
14
Product warranty 15
Customer card 16
About customer service 17
4
Safety
precaution
Installation
and power
connection
Use the trolley when moving the product because
it is heavy.
• It can cause injury or product damage when it drops.
Do not install the product in the place where it is
always moist.
• It can cause a fire.
Do not install the product where the product can
be submersed.
• It can cause an electric shock.
Do not install the product where the surface is
not even.
• It can block the inlet/outlet installed below the
power supply and damage the system.
• The meaning of the symbol shown on product and this manual are
as follows.
• This symbol shows the detail and operation that can result in
dangerous situation. Read carefully and follow the direction
with this symbol to avoid any dangerous situation.
• This symbol shows the potential situation with electric shock
under specific condition.
• Potential for major injury or human death
when directions are violated
• Potential for minor injury or product
damage when directions are violated
WARNING
CAUTION
WARNING
Do not put any objects that block the inlet/outlet to
ensure space to cool the product.
• It can cause problems to the product.
Less than
95% humidity
5
WARNING
Configure the switchboard to
electric capacity (7A) for each set.
• Always ground the product as it can
cause an electric shock or a fire.
• When using SSR, install the
product according to 20A capacity
specification per set.
Use the product at rated
specification.
• It can cause a fire or product
damage.
Firmly fixate the product
considering the installation
support, product weight (21kg)
and the vibration so that it does
not shake. [Always use fixating bolt
M8, spring washer and nut.]
• It can cause an injury if the
product falls.
21kg
After installing and fixating the
product, do not block the product
with alien material (Vinyl, silicon
etc.) as shown on the left.
• It can block the inlet/outlet installed
below the power supply and
damage the system.
Do not install the product
where it not ventilated well.
• It can cause heating of the
product or a fire.
Keep 30cm of clearance
from the case to the wall to
safely use the product.
• It can cause heating of the
product.
When laying down the product on
the floor, put it in the same
direction as shown in the picture.
• If not laid as shown in the picture, it
can cause product damage.
CAUTION
Current
capacity
7A
Within
±10%
Please do earth work.
• It can cause electric shock if not
do the earth work
Install earth leakage breaker and
exclusive switch.
• It can cause fire and electric shock
if not installed.
Do not use any heating device
or flammable material within
1m of the product.
• It can cause a fire or an
explosion.
Electric work has to be done by
certified technicians by technical
regulation on electric equipment or
indoor wiring specification and
regulation, and this installation guide.
A specific circuit has be used.
• It can cause fire and electric shock if
power capacity is inadequate or
electric work is faulty
Earth leakage
breaker
Exclusive
switch
6
Safety
precaution
Use and
Cleaning
Do not disassemble or reconfigure the product.
Do not use the product for underwater lighting.
(Underwater lighting display, exploration,
fishing, event etc.)
• It can cause a fire or an electric shock.
Never disassemble the main unit of the product.
• It can cause an electric shock from high voltage
electricity flowing inside the product.
• When the cover is arbitrarily disassembled, it can
cause an injury from leakage of microwave.
• Never take off the external cover unless done by the
service technician.
Never stare at the lamp when the lighting is
turned on.
• It can cause visual disorder due to the strong light.
Do not use the product for purposes other than
lighting. (Warning food, drying clothe)
• It can cause a fire.
WARNING
If the PLS is submersed in water, use the
product after repairing the product.
• It can cause a fire or an electric shock.
S
e
r
v
i
c
e
7
When the lamp is
abnormally turned off, do
not disassemble the
product, and always
request for service to the
service center.
• It can cause an electric
shock or problems to the
product.
Be careful not to let any
alien object (Pin, coin, steel
wire) get into the inlet/outlet
and internal/external hole on
the case.
• It can cause a fire or an
electric shock.
Do not use the product
when dropped or when
impact is applied.
• It can cause problems to
the product.
Do not use the product with
the cover on the exterior of
the product.
• It can cause a fire or an
electric shock.
When cleaning the
product, never spray water
directly on the main unit of
the product.
• It can cause a fire or an
electric shock.
When touching hot parts
(Cover glass, reflector etc.),
always wear safety gloves.
• Because the product is hot
while or after it is operating,
it can cause a burn.
WARNING
CAUTION
8
Installation
method
Before installing…
– This model (PSF1032A) is designed to be installed outdoors and
supports day to day water proofing.
– To prevent the product from falling by wind or other external force, use
the bolt and nut of M8 or above.
– Be careful not to let other objects interfere with product from cooling
and also be careful not to block the inlet/outlet when installing the
product.
– Installing the product in an environment that exceeds the usable
temperature and humidity can cause unexpected issues. Therefore
always consult with LG Electronics before installing the product.
– Installing the product in locations where chemicals such as TCE series
or chlorine gas are used or locations where vibration is excessive can
cause unexpected issues. Therefore always consult with LG Electronics
before installing the product.
– When using the product in highly dusty area, the illumination can be
reduced due to the dust. Therefore periodically clean the product and
do not install the product where metallic dust is generated.
– Install at least 1m from the ground clearance distance must be
maintained.
– The mark means min. distance from PLS to lighted object when install
the PLS, check the distance from PLS on the optical axis of PLS.
3m
1. Follow regulations of government agency for technical standard and
electric power company's guide regarding regulations on equipment
and wiring.
CAUTION
2. Do stated earth work when installing PLS
•
Do earthwork of PLS. Do not connect earth wire
with gas pipe, water pipe, lightning rod or
telephone line. It can cause electric shock as it
makes earthwork incomplete.
WARNING
WARNING
•
By the regulation and this installation guide,
electric work using a specific circuit must be done
by certified electric technician. It can cause fire or
electric shock if capacity of power supply circuit is
insufficient or faulty.
9
Component
and name
Product size
(Units : mm)
Case, Upper
Glass, Cover
Cover, Top
Case, Lower
Bolt, Aiming
Angle
Component and name
Cover, Front
Tilt, Swivel
Power Supply
Cover, Side
Cover, Back
Cable, High Voltage
Power Cord (Plug-less)
Accessories in box
Item
USER MANUAL
No. (EA)
1
10
Installation
criteria and
example
Power condition and switchboard
configuration for PLS installation
• Because the power consumption per 1 set of PLS is high,
the cross sectional area of the switchboard must
appropriately be applied, and for stable operation, one
control switch must be installed for each set.
• Grounding requires more than 3 grounding points and must
be wired for safety purposes.
Note)
MCCB: Molded Case Circuit Breaker
ELB: Earth Leakage Circuit Breaker
Use rate sensitivity current (Break current) of 30 [mA]
MS: Magnetic Switch (Used when applying GPS or auto flash device)
* PLS is not equipped with a terminal block. For installation, please get professional
assistance.
- Terminal Block Specification
(a) Rated Voltage: 250V or above
(b) Rated Power: 10A or above
(c) 3 way bolt fastening type
- After connecting power line to the terminal block, ensure that the power line makes
secure contact with fastening bolt or clamp and the power line is securely fastened.
PLS switchboard
(When installing 6 sets)
Apply
14.0
mm
2
or above
MCCB
75A or
above
Apply 2.0 mm
2
or above for
each line
Recommended to
apply ELB, MS
capacity of 10A
• After wiring power line to terminal box, check if the line touches tightening bolt or
clamp or is being forced.
• Use regulated electric wire so connecting part of terminal is knocked out by external
force. It can cause fire if connecting part is fixed tightly as it generates heat.
• Wire power line after ring terminal work. It can cause fire and failure of electric parts.
• Check Neutral status when installing main power
• Ending part of PLS has to be waterproof when connecting it to terminal.
WARNING
11
Case lower
– Refer to the dimension of the case below the power supply and fixate the product.
231
252
13
10
59 70 40
400
110
Inlet
Outlet
Bolt/Nut connection
(Hole with width of 10mm)
Base plate to fixate product
(Separately manufactured)
– Considering the safety of the system and installation, it is recommended to
manufacture the base plate separately to fixate the product. Refer to the
following drawing. (Not included in the product)
– If the base plate is not required, install the product by considering the cooling
path (Inlet/Outlet) of the system.
255,0
400,0
12,0
80,0
30,0
80,0
30,0
80,0
50,0
30,0
30,0
• When manufacturing the base plate to
fixate the product, always use steel
plate of L400xW272 (mm) 5T or above.
(Units : mm)
(Units : mm)
12
Installation
criteria and
example
Optical source
(LDM)
M8 Bolt
Bolt,
Aiming Angle
Outlet
Spring
Washer
M8 Nut
Base plate to
fixate product
Base Plate
Power supply
(PSM)
Inlet
• Install the product on even ground free from submersion.
• When adjusting the bolt (M12 bolt, aiming angle) to adjust
the PLS angle, always use a spanner and maintain torque
of 40kgf.cm or above.
13
Check
before
requesting
for service
Symptom Check points Action
Cooling fan is not
operating
Is the power outlet
220~240V?
Change to
220~240V power
outlet.
Light is turned off
within 5 minutes
after it is turned
on
Request for repair
service
Light flashes
within 5 minutes
after it is turned
on.
Does the flashing
continue even 5
minutes after the
light is turned on?
If the light flashes
within 5 minutes
after turning the
light on, it is not a
problem.
If the light
continues to flash
even after 5
minutes, request
for repair service.
14
Product
specification
: PSF1032A
: 220-240 V / 50 Hz
: 1000 W
: 2450 MHz 50 MHz
: L570 x W440 x H680 mm
: 21 kg
: 87,000 lm ± 4,350 lm
(Standard Color Temperature 7,500 K)
: 5,500 K, 6,500 K, 7,500 K
: 80 Ra ± 4 Ra
(Standard Color Temperature 7,500 K)
: 10˚, 20˚, 60˚
: –20 ˚C ~ +40 ˚C
: IP55
Model name
Rated voltage
Power consumption
ISM frequency
Dimension
Weight
Luminous flux
Color temperature
Color rendering index
Beam Angle
Temperature range
IP Grade
15
Because this Warranty Card specifying the date of purchase may be necessary for
sufficient service in case of a request for repair, please keep this Warranty Card carefully.
Quality assurance for this product shall be provided in accordance with the
details specified in the warranty card.
Because a period of warranty free of charge begins from the date of purchase,
please ask the applicable person to specify the date of purchase.
(If it is impossible or difficult to identify the date of purchase, the warranty
period shall begin on the date after the lapse of 3 months from the date of
manufacture or the date of completion of customs clearance.)
Warranty free of charge shall not be applied to any use of product under
abnormal conditions and environments (see the standard for installation
specified in the User Instruction), other than normal use of lighting product.
(including core components)
This Warranty Card is not re-issuable.
In case of supplies according to a separate contract (procurement, HOST,
single unit, etc), the terms and conditions of warranty under such contract shall
be applied.
Product warranty
Product name : PLS-type Induction Lamp
Date of Purchase :
Name of Customer :
Name of Retailer :
YY
Telephone #:
Telephone #:
Model name :
DDMM
Address:
Address:
Warranty
Period
1 year
20 Yeouido-dong
Yeongdeungpo-gu, Seoul, KOREA
16
Remark
Customer card
Product name :
Model name :
Date of Sale :
Name of Customer :
Telephone # :
Address :
Resident Registration Number :
E-mail Address :
PLS-type Induction Lamp
YY MM DD
This Customer Card will be used for customer management in a specialty store.
The aforementioned information will be used for better customer service.
Name of Specialty Store :
Name of Installation Engineer :
@
Warranty
Period
1 year
17
About customer service
A customer has a valuable right to benefit from a warranty free of charge for 1 year from the
date of purchase where any failure occurs during the use of product.
However, any repairs for failure due to customer's negligence or Act of God will be charged
even during a period of warranty free of charge.
Customer's Rights
In case of the following events, any service will be provided at a cost even during a
period of warranty free of charge.
In case of failure due to insertion of foreign substances (water, beverage, coffee, toy,
etc) into the product.
In case of damage or functional failure due to fall of the product or impact to the
product.
In case of damage in appearance or deformation due to solvent such as thinner or
benzene.
In case of failure due to the use of parts or consumables other than LG Electronics'
original parts.
In case of failure of product due to wrong authorization of using voltage.
In case of loss or damage of components due to customer's authorized disassembly of
product.
In case of failure due to Act of God (lightning, fire, damage from storm and flood, gas,
damage from sea water, earthquake, etc)
In case of failure due to non-compliance of “Safety Instructions” in the user instruction
(Following “Safety Instruction” ensures a long-lifespan of product.)
In case of failure of product due to customer's other negligence.
Responsibility for charged service (Customer's payment of expense)
18
Memo
19
Memo
* This product is not serviced generally Authorized LG Service Centers. Contact installed
company for PLS or above call center number.
Contents of User’s Manual are based on October, 2010 and may be changed without a prior notice.
Contact for product use and quality
If you need a service due to the problem of the
product, contact the following number.
We will provide friendly accurate service fast.
Product purchase and other questions
Please contact the specialized
dealer of the applicable region
or the retailer.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Fluke PLS FS Owner's manual
-
Samsung RVXMHF050BA User manual
-
-
IWAKI IX-C060 TC/TE N User manual
-
YMGI WMMS-09K-V2A(57)2/25 Installation guide
-
Nilfisk-ALTO NEPTUNE 5 FA User manual
-
-
-
Toshiba LF546 User manual
-
Samsung AE160RXYDGG/EU User manual
