CURT 114683 Installation guide

CURT
Brand
CURT
Model
114683
Type
Installation guide

CURT 114683 is a weight-carrying hitch designed for use with the Toyota Prius. It has a gross load capacity of 2000 lbs. and a tongue weight capacity of 200 lbs. The hitch is easy to install, with no drilling required. It comes with all the necessary hardware, and can be installed in about 30 minutes by a professional or 60 minutes by a novice. The hitch is designed to be used with ballmounts #55001 and 45501. It is important to periodically check the hitch to ensure that all fasteners are tight and that all structural components are sound.

CURT 114683 is a weight-carrying hitch designed for use with the Toyota Prius. It has a gross load capacity of 2000 lbs. and a tongue weight capacity of 200 lbs. The hitch is easy to install, with no drilling required. It comes with all the necessary hardware, and can be installed in about 30 minutes by a professional or 60 minutes by a novice. The hitch is designed to be used with ballmounts #55001 and 45501. It is important to periodically check the hitch to ensure that all fasteners are tight and that all structural components are sound.

Parts List
DESCRIPTION
PART NUMBER
QTY
ITEM
CONICAL TOOTHED WASHER3/8"41
HEX BOLTM10 - 1.25 x 25
4
2
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.
***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.***
WARNING: ALL NON-TRAILER LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED BY AUXILIARY STABILIZING STRAPS.
** FAILURE TO PROPERLY SUPPORT NON-TRAILER LOADS WILL VOID PRODUCT WARRANTY**
HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-800-798-0813
HITCH WEIGHT: LBS.
INSTALL TIME
PROFESSIONAL: MINUTES
NOVICE (DIY): MINUTES
INSTALL NOTES:
INSTALLATION STEPS
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS
ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
Curt Manufacturing Inc., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,
Curt Manufacturing Inc., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of
this product voids the warranty. Curt Manufacturing Inc.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or
consequential loss or damage.
2,000 200
30
30
TOYOTA PRIUS
9/11/2009
11468
60
24743
EXISTING TOW HOOK SLOT
ENLARGED TOW
HOOK SLOT
UNDER BODY FACIA ON DRIVER SIDE
1) Remove tow hooks. (Return to customer)
2) Remove plastic under body fascia on driver side.
3) Lift hitch into postion and secure with M10 bolts and conical washers as shown.
4) Torque all M10 fasteners to 35 ft-lbs.
5) Enlarge tow hook slot on under body fascia to fit around driver side plate as shown.
6) Reinstall under body fascia with existing hardware.
NO DRILLING REQUIRED
TRIM UNDER BODY FASCIA
EXISTING WELD NUTS
IN FRAME
FRAME RAIL
EXISTING WELD NUTS
IN FRAME
FRAME RAIL
1
2
DESIGNED FOR USE WITH
BALLMOUNT #55001 / 45501
  • Page 1 1

CURT 114683 Installation guide

CURT
Brand
CURT
Model
114683
Type
Installation guide

CURT 114683 is a weight-carrying hitch designed for use with the Toyota Prius. It has a gross load capacity of 2000 lbs. and a tongue weight capacity of 200 lbs. The hitch is easy to install, with no drilling required. It comes with all the necessary hardware, and can be installed in about 30 minutes by a professional or 60 minutes by a novice. The hitch is designed to be used with ballmounts #55001 and 45501. It is important to periodically check the hitch to ensure that all fasteners are tight and that all structural components are sound.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents