AGA DUAL CONTROL
DC3G & DC5G
(CONVENTIONAL FLUE)
For use in GB & IE
PLEASE READ THESE INSTRUCTIONS BEFORE USING THIS APPLIANCE
AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.
Burner Assembly
Upgrade Instructions
REMEMBER, when replacing a part on this appliance, use only spare parts that you can be assured conform to the
safety and performance specication that we require.
DO NOT use reconditioned or copy parts that have not been clearly authorised by AGA.
09/16 LPRT 517435
1
B
A
A
B
1. Overview
1. Isolate mains gas & electricity supplies.
2. Remove fascia panel (4 mirror caps, 4 screws)
3. Turn gas cock to ‘OFF’ position.
4. Disconnect union joint to gas cock.
5. Disconnect Thermocouple connections (A & B) from
ue safety thermostat (LM7) Fig. 1.1.
6. From inside top of roast oven remove phial mounting
plate & unclip phials from circlips.
7. Remove thermodial mounting bracket (2 screws)
c/w thermodial attached, taking care not to damage
capillary.
8. Withdraw thermodial & control valve capillaries
through guide tube into burner housing. Place
thermodial & bracket aside.
9. Remove 4 screws securing burner assembly to
housing, and withdraw burner assembly from burner
chamber.
10. Fit new burner assembly. Re-connect thermocouple
connections to ue safety thermostat (LM7). Ensure
control valve capillary is routed to RH side of burner
housing as shown in care notice.
11. Re-t thermodial & control valve capillaries through
guide tube into roast oven. Re-t to phial mounting
plate Fig. 1.2.
12. Re-t thermodial mounting bracket to housing (2
screws).
13. Turn gas cock to ‘ON’ position.
14. Restore gas & electric supply to appliance.
15. Check for gas tightness. Refer to installation
instructions EINS517055 for inlet & burner pressure
testing.
16. Re-commission cooker. Refer to installation
instructions EINS517055.
Fig. 1.1
Fig. 1.2
A. Thermostat Capillary B. Thermodial Capillary
2
Phial Wire
2. Care Notice
Fig. 2.1
Gas valve oven thermostat phial wire
Fig. 2.1
Following assembly of gas valve thermostat phial into
oven cavity, excess wire may cause an ‘Electrical
Shorting’ problem across simmering plate thermostat
terminals if routed loosely behind thermodial inside the
controls assembly.
To avoid this, phial wire should be routed towards the
right-hand side of the controls housing. Excess wire can
then be ‘coiled’ and positioned toward the bottom right-
hand corner of controls housing.
Similarly, the braided wire from the thermodial should also
be routed toward thr right-hand side of controls housing to
prevent similar problems occurring.
With AGA Rangemaster’s policy of continuous product
improvement, the Company reserves the right to
change specications and make modications to the
appliances described and illustrated at any time.
www.agaliving.com
www.agacookshop.co.uk
Manufactured By
AGA Rangemaster
Station Road
Ketley Telford
Shropshire TF1 5AQ
England
For further advice or information contact
your local AGA Specialist.
-
1
-
2
-
3
-
4
AGA DC3 & DC5 Conventional Flue Burner Assembly Upgrade s Owner's manual
- Type
- Owner's manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
AGA DC3 & DC5 Power Flue Burner Assembly and Flue System Upgrade Owner's manual
-
-
AGA ALEG44DFIVY Legacy 44 Service Manual
-
-
-
-
-
AGA Rayburn 400 Series 480AG_CF Natural Gas User guide
-
-
Other documents
-
Heartland HL-CKLP Owner's manual
-
Aga Ranges F104010-01 User manual
-
Falcon Elan 110 Dual Fuel User's Manual & Installation Instructions
-
Rayburn 200 G User Instructions
-
Rangemaster U109600-02 User manual
-
-
-
-
-
