American Standard 2771.018WC.222 User manual

American Standard

Brand: American Standard

Model: 2771.018WC.222

Type: User manual

INSTALLATION INSTRUCTIONS

752500-100 REV. G

© American Standard Inc. 2003

All product names listed herein are trademarks

of American Standard Inc. unless otherwise noted.

HIGH GLOSS ACRYLIC

SHOWN LESS ALL FITTINGS

CADET™ 5' x 36"

WHIRLPOOL/BATHING POOL

2771.XXXW SERIES

FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.

THANK YOU...

for selecting an American Standard bath. Your new

bath is shipped to you after careful inspection. The

whirlpool version is completely assembled with pump,

motor, and system piping. All you need to finish the

installation are your selected fittings and electrical

connections for a whirlpool.

To insure maximum performance and pleasure from

this product, please follow the instructions and

cautions.

GENERAL INSTALLATION INFORMATION

Carefully uncrate and inspect your new bath for any shipping damage. If such damage is found, report it to your vendor

immediately.

After inspection and during installation, protect the bath from construction damage. After installation, and before

enclosing with wallboard, tile, etc., water test the unit and check for leaks.

Do not make modifications to the whirlpool system or remove pump from factory mounting. This could adversely affect

the safety and performance of the whirlpool and void the warranty. Do not handle or move the whirlpool by the pump,

motor, or piping system.

Fittings (bath filler, shower arm, etc.) are not provided with the bath and must be ordered separately. Framing and

enclosing materials are provided by others. Check for availability of optional American Standard wall tiling bead

(required for recess installations).

Protect all finished surfaces of the whirlpool during construction and installation using a drop cloth.

WARNING! Do not lift whirlpool by the piping harness at any time.

List of Optional Components (not included):

• Safe-T-Heater 9075.120*

• Tile Bead Kit - 751755-100*

• Apron Kit*

List of Required Components (not included):

• Drain 1583.470* • Bath Filler*

* see your American Standard Distributor

List of Required Tools and Supplies:

Tools

• Level

• Tape Measure

• Pipe Wrench

• Slip Joint Pliers

• Screw Driver

• Standard

Woodworking Tools

• Personal Safety

Equipment

• Caulking Gun

Supplies

• Nails

• Putty

• Caulking (waterproof)

• 1 x 3 or 2 x 2

Stringers

• Drop Cloth

• 15 amp GFI

Outlet

• Cement, Plaster,

Grout

RECOMMENDED FITTING LOCATION

64 X 330mm (2-1/2 x 13")

FOR PIER OR ISLAND

INSTALLATIONS ONLY

ALT. FITTING

LOCATION #1

464 mm

(18-1/4)

38 mm

(1-1/2)

502 mm

(19-3/4)

1-1/2 O.D.TAILPIECE

■ LEVELING

STRINGER

NOT FOR

SUPPORT

SAFE-T-HEATER

REMOVABLE

BLANK

ROUGH

FLOOR

1524 mm

(60)

914 mm

(36)

OUTLINE OF CUTOUT

1486 mm x 876 mm

(58-1/2 X 34-1/2)

457 mm

(18)

235 mm

(9-1/4)

305 mm

(12)

57 mm

(2-1/4)

(8) JETS

76 mm

(3)

CUTOUT IN FLOOR

FOR DRAIN

PUMP

FINISHED

WALL

305 mm

(12)

OPTIONAL TO

FINISHED FLOOR

USUALLY BETWEEN

1651 & 1981mm

(65 & 78)

C/L OF

OVERFLOW

102 mm

(4)

C/L OF

SPOUT

C/L OF

VALVES

C/L OF

SHOWER ARM

70 mm

(2-3/4)

117 mm

(4-5/8)

1-1/2 N.P.T.M.

THREADS

19 mm

(3/4)

229 mm

(9)

C/L OF

SUPPLIES

C/L OF DRAIN

SEE FITTING

SPECS FOR

DIMENSIONS

(2) AIR VALVES

ON/OFF

SWITCH

PROVIDE ACCESS TO PUMP FOR

SERVICING ON ALL INSTALLATIONS

INTEGRAL

SUPPORT

FEET

60 x 36 x 19-3/4 In.

(1524mm x 914 mm x 502mm)

95 Lbs. (43 Kg.)

587 Lbs. (267 Kg.)

59 Gal. (224 L.)

48 Gal. (182 L.)

40 x 22 In. (1016mm x 559mm)

52 x 29 In. (1321mm x 737mm)

13-1/4 In. (337mm)

39 Lbs./Sq. Ft. (188 Kgs/Sq. m.)

23.8

44.5

GENERAL SPECIFICATIONS FOR 2771 WHIRLPOOL

INSTALLED SIZE

WEIGHT

WEIGHT w/WATER

GAL. TO OVERFLOW

MIN. OPERATING GAL.

BATHING WELL AT SUMP

BATHING WELL AT RIM

WATER DEPTH TO OVERFLOW

FLOOR LOADING

(PROJECTED AREA)

PTS.

CUBE (FT

3

)

WHIRLPOOL ELECTRICAL SPECIFICATIONS

1.6 HP, 9.7 AMPS, 120V.PUMP

1486mm

(58-1/2)

CUTOUT

TYPICAL RECESS INSTALLATION

LEVELING

SURFACE

WATERPROOF

SEALANT

BATH

WHIRLPOOL ONLY:

UNLESS AN ACCESS OPENING OF AT LEAST

12" X 24" (305 X 610MM) IS PROVIDED,

WARRANTY SERVICE WILL NOT BE PERFORMED.

TYPICAL PIER TYPE INSTALLATION

AS DESIRED

876 mm

(34-1/2)

CUTOUT

AS DESIRED

464mm

(18-1/4)

ACCESS PANEL

610mm

(24)

305mm

(12)

610mm

(24)

305mm

(12)

464mm

(18-1/4)

464mm

(18-1/4)

1527mm

(60-1/8)

876mm

(34-1/2)

914mm

(36)

TUB WIDTH

LEVELING

STRINGERS

WHIRLPOOL ONLY:

UNLESS AN ACCESS OPENING OF AT LEAST

12" X 24" (305 X 610MM) IS PROVIDED,

WARRANTY SERVICE WILL NOT BE PERFORMED.

INSTALLATION AND FRAMING INSTRUCTIONS

The variety of installations possible for this whirlpool may require framing procedures other than those shown. Locate studs

as required. Ensure roughing-in dimensions are proper, plumb and square. Provisions must be made in all installations for an

access opening for servicing the pump and controls. It is strongly recommended that an additional opening be provided for

access to the drain components.

NOTE: The apron should not be used as the primary access opening.

1. Position the whirlpool into the installation opening and level the deck, shimming the integral support feet as necessary.

Mark the final position of the underside of the deck by tracing a line on to the studs (see Figure 1).

2. Remove the whirlpool and attach a 2 x 4 stringer to the studs, with the top of the stringer touching the traced line.

3. Install drain components to the whirlpool following the manufacturers instructions. Before replacing your whirlpool for final

installation, be certain that an opening has been provided in the sub-floor for the drain. See the roughing-in drawing for

suggested opening size and location dimensions.

4. Replace whirlpool and re-shim the integral support feet, shimming the entire length of the support feet. Secure the shims

using construction adhesive, silicone, mortar or equivalent materials. While not a necessity, the use of a foundation base

consisting of cement (e.g. Sakrete), mortar, or grout will help provide a solid and secure installation.

752500-100 REV. G (2)

TILE

TILE

BEAD

STRIP

LEVELING

STRINGER

BATH

ADHESIVE

SEALANT

WALLBOARD

NOTE: Tile bead kit not included and must be

purchased separately.

FIG. 1

ELECTRICAL DIAGRAM

READ AND FOLLOW ALL INSTRUCTIONS

BLACK

WHITE

120 VAC

GND.

SEPARATE

15 AMP GFCI

OUTLET

WHIRLPOOL MOUNTED

AIR SWITCH OR

WALL TIMER

ELECTRICAL INSTALLATION

PUMP/MOTOR

752500-100 REV. G

ELECTRICAL INSTALLATION INSTRUCTIONS

All wiring must be performed by a licensed electrician in accordance with the national electrical code and all other

applicable codes.

WARNING:

When using electrical products, basic precautions should always be observed, including the following:

1. DANGER: RISK OF ELECTRIC SHOCK

Connect only to a circuit protected by a ground-fault circuit interrupter.

2. Grounding is required. The unit should be installed by a licensed electrician and grounded.

3. Install to permit access for servicing.

4. All building materials and wiring should be routed away from the pump body and heater (if equipped).

The whirlpool should be installed on a 120 vac, 15 amp dedicated circuit. The circuit should be hard-wired from the

electrical power supply panel. The circuit must be a three (3) wire circuit from the electrical supply panel. A grounded

neutral wire and a third wire, earth ground, are essential. SAFE-T-HEATER EQUIPPED MODELS REQUIRE A

SEPARATE 15 AMP MAXIMUM GFCI CIRCUIT.

(3)

Motor

Hi Performance

Rating

1.6

WIRE SELECTION GUIDE

752500-100 REV. G

DRAIN CONNECTION AND SYSTEM TEST

Using recommended drain opening, connect whirlpool drain to waste line. Tighten all drain joints securely. Check the

pump couplings and make sure they are hand-tight. Clean the whirlpool and fill with water to a point 2" above the top of

the highest jet. Recheck the pump couplings and make certain that they are not leaking. (Although the pump couplings

are factory tightened and inspected, some loosening may have occured during transit.) Make sure the whirlpool is

connected to the electrical supply and turn the whirlpool on. Check for leaks around all piping connections while the

whirlpool is running.

POST INSTALLATION CLEAN-UP

Remove all construction debris from bath. Tile grout can be removed with a wooden popsicle stick or tongue depressor.

Do not use wire brushes or any other metal implement on bath surface.

Post installation clean-up generally can be completed using warm water and liquid dishwashing detergent. Stubborn dirt or

stains may be removed using granular Spic and Span

®

mixed with water.

Painter's naphtha can be used to remove excess adhesives and/or wet oil-base paint.

HARSH CHEMICALS SHOULD NEVER BE USED ON ACRYLIC SURFACES.

Abrasive cleaners must not be used since they will scratch and dull the surface. Dulled areas can be restored by rubbing

with a white automotive-type polishing compound and waxing with a liquid wax.

Maximum distance from

fusebox to motor

The sizes shown on this

chart are recommendations

for copper conductors

only. Always follow

local and national

electrical codes

50' 100'

115V Power Line

150' 200'

12 12 10 8

(4)

SPIC AND SPAN

®

IS A REGISTERED TRADEMARK OF PROCTER & GAMBLE

1
2
3
4

American Standard 2771.018WC.222 User manual

American Standard

Brand: American Standard

Model: 2771.018WC.222

Type: User manual

Download PDF

Related papers

Other documents