Hotpoint Ariston HNC 6.6 AMI X/HA User guide

HNC 6.8 ABI X/HA

HNC 9.8 ABI X/HA

HNC 9.6 AMI X/HA

HNC 6.6 AMI X/HA

English

Operating Instructions

COOKER HOOD

Français

Mode d’emploi

HOTTE DE CUISINE

Español

Manual de instrucciones

CAMPANA

Italiano

Istruzioni per l’uso

CAPPA

Portuges

Instruções para a utilização

EXAUSTOR

Sommario

Istruzioni per l’uso,1

Avvertenze,9

Assistenza,28

Installazione,31

Comandi CHIMNEY,32

Manutenzione e cura,33

Anomalie e rimedi,34

Contents

Operating Instructions,1

Warnings,10

Assistance,28

Installation,35

CHIMNEY controls,36

Maintenance and care,37

Troubleshooting,38

Sommaire

Mode d’emploi,1

Avertissements,11

Assistance,28

Installation,39

Commandes CHIMNEY,40

Entretien et soin,41

Anomalies et remèdes,42

Sumario

Manual de instrucciones,1

Advertencias,13

Asistencia,28

Instalación,43

Mandos CHIMNEY,44

Mantenimiento y cuidados,45

Anomalías y soluciones,46

Índice

Instruções para a utilização,1

Advertências,14

Assistência,28

Instalação,47

Comandos CHIMNEY,48

Manutenção e cuidado,49

Anomalias e soluções,50

Page is loading ...

10

• E’ severamente vietato cucinare cibi a

ﬁ amma libera sotto la cappa; l’impiego

di ﬁ amma libera è dannoso ai ﬁ ltri e

può dar luogo ad incendi, pertanto deve

essere evitato in ogni caso.

• Si consiglia di tenere sotto costante

controllo la cottura di cibi tramite frittura,

al ﬁ ne di evitare che l’olio surriscaldato

prenda fuoco.

• Per quanto riguarda le misure tecniche

e di sicurezza da adottare per lo scarico

dei fumi attenersi strettamente a quanto

previsto dai regolamenti delle autorità

locali competenti.

• Si consiglia di pulire frequentemente

il prodotto, sia internamente che

esternamente (ALMENO UNA VOLTA

AL MESE, rispettare comunque quanto

espressamente indicato nelle istruzioni

di manutenzione riportate in questo

manuale).

• L’inosservanza delle norme di pulizia

della cappa e della sostituzione e pulizia

dei ﬁ ltri comporta rischi di incendi.

• Non utilizzare o lasciare la cappa priva

di lampade correttamente montate per

possibile rischio di scossa elettrica.

• Si declina ogni responsabilità per

eventuali inconvenienti, danni o incendi

provocati all’apparecchio derivati

dall’inosservanza delle istruzioni

riportate in questo manuale.

• Attenzione! Le parti accessibili possono

diventare molto calde se utilizzate con

degli apparecchi di cottura.

Warnings

! Keep this manual for reference. If you

sell, transfer or move the unit to another

location, make sure to keep the manual

with the product.

! Read the instructions carefully - they

contain important installation, user and

safety information.

! Do not tamper with the electrical or

mechanical equipment of the product or

its exhaust ducts.

General safety information

• The distance between the cookware

support surface on top of the cooking

appliance and the lowest part of the

cooker hood must be at least:

65 cm if the hood is installed over a gas

cooktop

55 cm if the hood is installed over an

electric cooktop.

If the installation instruction manual for

the gas cooking appliance speciﬁ es a

greater distance, this measurement

should be taken into account.

• The cooker hood comes with anchor

plugs which are suitable for use with

most walls/ceilings.

However, you must contact a qualiﬁ ed

technician to check the suitability of the

materials in relation to the type of wall/

ceiling, which must be strong enough

to support the weight of the unit.

• Caution! Do not hook the unit up to

its electrical power supply until the

installation has been completed.

11

• Before cleaning or servicing the unit,

disconnect it from the mains by pulling

the power plug or disconnecting the

main circuit breaker.

• Always wear work gloves when installing

and servicing the unit.

• It is not intended for use by children

or persons with sensory or mental

disability and lack of experience or

familiarity, except under the supervision

or instruction of a person responsible

for their safety.

• Make sure children do not play with the

unit.

• Never operate the unit without its

grease ﬁ lter installed!

• NEVER use the hood as a support,

unless expressly instructed to do so.

• The room must be adequately ventilated

if the hood is used at the same time with

other equipment burning gas or other

fuels.

• Extracted air must not be conveyed into

a duct used for exhausting combustion

fumes from gas or other fuel-fired

equipment.

• Observe all regulations in relation to air

extraction.

• NEVER cook food with an open ﬂ ame

under the hood; open flames will

damage the ﬁ lters and may cause ﬁ res.

Never do this.

• Always supervise frying to make sure

the heated oil does not catch ﬁ re.

• Strictly observe all local regulations

in relation to the technical and safety

measures to be employed in fumes

extraction.

• Clean the product frequently, inside

and out (AT LEAST ONCE A MONTH,

and in observance of the maintenance

instruction given in this manual).

• Failure to observe the hood cleaning and

ﬁ lter cleaning/replacement instructions

can result in ﬁ res.

• Never use the hood without its bulbs

properly installed - electrocution hazard.

• The manufacturer is not liable for any

inconvenience, damage or ﬁ re caused

by the unit as a result of failure to

observe the instructions given in this

manual.

• Caution! The unit's accessible parts can

get very hot when used with cooking

equipment.

Avertissements

! Il est important de conserver ce manuel

afin de pouvoir le consulter à tout

moment. En cas de vente, cession ou

déménagement, assurez-vous qu'il

accompagne toujours le produit.

! Veuillez lire attentivement les

instructions : elles contiennent des

informations importantes sur l'installation,

l'utilisation et la sécurité.

! N'apportez pas de modifications

électriques ou mécaniques sur le produit

ou sur les conduits d'évacuation.

Page is loading ...

GB

35

Installation

The installation procedure is illustrated in the ﬁ rst pages

of this manual.

The installation must be done by a qualiﬁ ed technician.

Electrical hook up

The mains voltage must match that given on the ratings

label inside the hood itself. If the hood has a power plug,

connect the hood to an easily accessible regulatory power

socket. If it does not (direct connection to the mains), or the

socket is not easily accessible, install a two-pole regulatory

switch to enable total disconnection from the mains in case

of category III overvoltage, as required by the installation

regulations.

Caution! Always check that the mains cable is hooked

up properly and check that it operates correctly before

reconnecting the hood to the mains.

Air exhaust (for ducted units)

Connect the hood to a duct and wall exhaust hole of a

diameter equal to that of the air outlet ﬂ ange. Using a smaller

diameter tube and exhaust hole reduces the extraction

capacity of the hood and also increases its running noise.

The manufacturer is not liable for any consequences of

doing so.

! Use the shortest duct required to achieve the purpose.

! Use a duct with as few bends as possible

! Avoid suddenly changing the diameter of the duct.

! The duct must have as smooth an inner surface as

possible.

! The duct must be made of regulatory material.

! Do not connect the hood to ﬂ ues carrying combustion

fumes from other equipment (boilers, chimneys, stoves,

etc.).

! Observe the instructions of the competent authorities in

relation to the air exhaust. The air being exhausted may not

be exhausted into a wall cavity unless the cavity in question

is speciﬁ cally intended for this purpose.

! Equip the room with air intakes to prevent the hood creating

suction pressure in the interior (this must not exceed 0.04

mbar).

! The manufacturer is not liable for any consequences of

failure to observe these instructions.

Filter or ducted?

! Your hood is supplied as a ducted unit.

If you wish to use it as a ﬁ lter unit, you must install the proper

ACCESSORY KIT.

Note: If supplied with the hood, the accessory active

charcoal ﬁ lter unit may already be installed.

Instructions for transforming the hood from the ducted to the

ﬁ lter version are given in this manual (see “Filter version”).

Ducted version

The hood puriﬁ es the air and expels it outdoors via an

exhaust duct (dia. 150mm) connected to its outlet ﬂ ange.

The diameter of the exhaust tube must be equal to that of

the outlet ﬂ ange.

Caution! The exhaust duct is not supplied and must be

purchased separately.

When routed horizontally, the tube must be angled slightly

upwards (around 10°) to enable the air to be conveyed

outdoors more easily. If the hood is ﬁ tted with charcoal

ﬁ lters, they must ﬁ rst be removed.

Filter version

The hood puriﬁ es the air and returns it to the room. This

version of the hood requires installation of an accessory

active charcoal ﬁ lter unit.

This version requires an air deﬂ ector, a reduction adapter

and the charcoal ﬁ lter/s. The top tube must have its air

outlet slots uppermost.

Technical data

Model

Height

(cm)

Width

(cm)

Depth

(cm)

dia. of

exhaust tube

(cm)

CHIMNEY 60cm 61-82 59.8 50 15/12

CHIMNEY 90cm 61-82 89.9 50 15/12

Model code Bulb (V) Bulb draw (W) Total draw (W)

HNC 6.8 ABI X/HA

HNC 9.8 ABI X/HA

Halogen 2 x 40 290

Model code Bulb (V) Bulb draw (W) Total draw (W)

HNC 9.6 AMI X/HA

HNC 6.6 AMI X/HA

Halogen 2 x 40 210

Power Voltage Cap Dimensions

Halogen 25 W 2 x 25 W 230 V G9 L40xØ14

Halogen 20 W 2 x 20 W 12 V G4 L30xØ10

LED *

Risk Group 1 according to Standard EN 62471

The hoods are conforming to the following EC

Directives:

• “Low voltage” Directive 2006/95/EC (12-12-2006)

• “EMC” Directive 2004/108/EC (15-12-2004)

* Only available in certain models

36

GB

CHIMNEY controls

Models with mechanical keypad

HNC 9.6 AMI X/HA - HNC 6.6 AMI X/HA

T1 T2 T3 T4 T5

T1 Motor reset

Pressing the button while the hood is in operation turns it

OFF.

T2 Speed 1

Pressing the button sets the hood to speed 1.

T3 Speed 2

Pressing the button sets the hood to speed 2.

T4 Speed 3

Pressing the button sets the hood to speed 3.

T5 Lights ON/OFF

Models with soft button keypad

HNC 6.8 ABI X/HA - HNC 9.8 ABI X/HA

T1 T2 T3 T4 T5

B

T6

T1 Motor reset

Pressing the button while the hood is in operation turns it

OFF.

T2 Speed 1

Pressing the button sets the hood to speed 1.

T3 Speed 2

Pressing the button sets the hood to speed 2.

T4 Speed 3

Pressing the button sets the hood to speed 3.

T5 Booster

Pressing the button sets the hood to high speed. After 5

minutes, the hood returns to the previous speed; pressing

a speed button (T2, T3 or T4) quits booster mode and sets

the selected speed.

T6 Lights ON/OFF

Grease/odour ﬁ lter warnings

The T2 icon ﬂ ashes to indicate that the grease ﬁ lter is

saturated, while T3 ﬂ ashes to indicate that the odour ﬁ lter

is saturated, and if both are ﬂ ashing then both ﬁ lters are

saturated. You must then clean/replace the grease ﬁ lter (A)

or odour ﬁ lter (B) or both, accordingly (see “Maintenance

and care”).

To reset the ﬁ lter counter:

Hold down T4 for three seconds while the hood is on.

The warning led ﬂ ashes three times, then returns to its

normal mode If both ﬁ lter warnings are active at the same

time, you must reset each separately.

The ﬁ rst sequence resets the grease ﬁ lter, while the second

sequence resets the odour ﬁ lter.

Hood conﬁ guration:

To set the operating mode of the hood, hold down T5 for 6

seconds while the product is off. Icons T2 or T3 will light up

to show the type of installation: T2 ventilation, T3 ﬁ ltering.

You can change the type of installation by pressing T4

cyclically.

To save the new conﬁ guration press T1 individually.

Models with soft button keypad and display

(Only available in certain models)

T1 T2 T3 T4 T5 T6

B

1 Motor ON/OFF

Press the button with the hood off to set speed 1. Pressing

the button while the hood is in operation turns it OFF.

T2 Speed -

Pressing the button returns the hood to the previous speed.

T3 Speed +

Pressing the button returns the hood to the next speed. If

the hood is off, pressing these buttons sets speed 1.

T4 Booster

Pressing this button sets the hood to high speed; the letter

"b" ﬂ ashes slowly on the display. After 5 minutes, the hood

returns to its previous speed; this can also be done while

booster mode is on by pressing either speed button (T2

or T3).

T5 Timer

Pressing this button delays the hood turning off automatically

by 5 minutes. The timer counts down on the display in

minutes. The timer can only be set for manual speeds, not

for booster mode.

T6 Lights ON/OFF

GB

37

Grease/odour ﬁ lter warnings

The bar at the top left ﬂ ashes to indicate

that the grease ﬁ lter is saturated.

The bar at the top right ﬂ ashes to indicate

that the odour ﬁ lter is saturated.

If both bars are ﬂ ashing, then both ﬁ lters

are saturated.

You must then clean/replace the grease ﬁ lter (A) or odour

ﬁ lter (B) or both, accordingly (see “Maintenance and care”).

The latter only applies to the ﬁ lter version.

To reset the ﬁ lter counter:

Hold down T4 for three seconds while the hood is on.

If both ﬁ lter warnings are active at the same time, you must

reset each separately. The ﬁ rst sequence resets the grease

ﬁ lter, while the second sequence resets the odour ﬁ lter.

Conﬁ guring the hood

To set the operating mode of the hood, hold down T4 for 6

seconds while the product is off. After a long beep, the type

of installation displays: :

Ducted

(square at bottom left ﬂ ashing).

Filter

(square at bottom right ﬂ ashing).

You can change the type of installation by pressing T4. To

quit conﬁ guration mode, press T1 once; this switches the

unit off and saves the last displayed setting.

Maintenance and care

Caution! Before cleaning or servicing the unit,

disconnect it from the mains by pulling the power plug

or disconnecting the main circuit breaker.

First cleaning

• Remove the protective ﬁ lm

• Clean with a damp sponge and a little neutral soap

• Rinse off with a damp cloth

• Dry with a soft cloth; if the hood is stainless steel, dry

along the metal's grain

Periodic cleaning

The hood must be cleaned frequently (at least as often as

you service the grease ﬁ lter), inside and out. Use a damp

cloth and a neutral liquid detergent with lukewarm water.

Do not use abrasive or corrosive products.

Warning: Failure to observe the hood cleaning and ﬁ lter

cleaning/replacement instructions can result in ﬁ res. Follow

the instructions carefully. The manufacturer is not liable for

any damage to the motor or ﬁ res caused by incorrect care

or failure to follow the above instructions.

Servicing the grease ﬁ lter (A)

A

The grease ﬁ lter retains the

particles of grease produced

during cooking; it must be

cleaned at least once a month

with a non-aggressive

detergent, either by hand or

with a low temperature, short

dishwasher cycle.

To extract the grease ﬁ lter,

pull the spring loaded handle.

If washed in a dishwasher, the metal ﬁ lter may change

colour, but this does not affect its performance.

Servicing the charcoal ﬁ lter (B)

The charcoal ﬁ lter retains unpleasant cooking odours. The

ﬁ lter saturates after a variable time, depending on the type

of cooking and how often the grease ﬁ lter is cleaned. The

cartridge must be replaced at least once every twenty months.

This ﬁ lter can NOT be washed or regenerated

B

Disassembly: Remove the

activated-carbon filter by

pressing the two front levers

which secure it to the hood.

B

Assembly: Secure the

activated-carbon ﬁ lter ﬁ rst in

the back using the hood's

metal tabs and then in the

front by pressing the two

levers.

38

GB

Replacing the bulbs

Disconnect the unit from the mains and remove the grease

ﬁ lter.

Caution! Make sure the bulbs are cool before touching

them.

1. Extract the guard by prising

it out with a small ﬂ at head

screwdriver or something

similar.

2. Replace the faulty bulb.

Use only bulbs of the

same type (for details,

see the technical data in

the following manual).

3. Reﬁ t the guard (push it in).

Replacing the lights LED

*

The hood is ﬁ tted with a lighting system based on LED

technology. The LEDs ensure optimal lighting, longer life

and lower consumption compared with traditional lights. To

replace them please contact the assistance service.

Electrical cable

If the power cable is damaged, it can be replaced by the

manufacturer or his technical service, to prevent any

attendant risks.

SCRAPPING

The unit is marked for conformity with European Directive

2012/19/EC, Waste Electrical and Electronic Equipment

(WEEE). By ensuring that the unit is scrapped properly,

the user contributes to safeguarding the environment and

public health.

The

symbol on the product or on its accompanying

documents indicates that the product may not be treated

as domestic waste but must be handed over to a sorting

centre for electrical and electronic waste. Dispose of it

in accordance with local waste disposal regulations. For

further information on the handling, recovery and recycling

of this product, contact the local authority, domestic waste

disposal service or the reseller from whom you purchased it

Troubleshooting

If something does not work, make the following simple

checks before contacting Technical Service:

If the hood does not operate:

Check that:

• the unit is powered up.

• a speed has been set.

If the hood is not working effectively:

Check that:

• the selected motor speed is sufﬁ cient to handle the

amount of smoke and steam being produced.

• the kitchen is adequately ventilated for the unit to take

air in.

• the charcoal ﬁ lter is not exhausted (ﬁ lter version).

If the hood turns off during normal operation:

Check that:

• the unit is powered up.

• the circuit breaker has not tripped.

In case of faulty operation, before contacting Technical

service, ﬁ rst disconnect the machine from the mains for at

least 5 seconds by pulling its plug, then reconnect it. If the

fault persist, contact Technical Service.

* Only available in certain models

Page is loading ...

Hotpoint Ariston HNC 6.6 AMI X/HA User guide

Hotpoint Ariston HNC 6.6 AMI X/HA User guide

in other languages

Related papers

Other documents