KitchenAid KUDC03IV User manual

Category
Dishwashers
Type
User manual
INSTALLATION INSTRUCTIONS
UNDERCOUNTER DISHWASHER
INSTRUCTIONS D'INSTALLATION
LAVE-VAISSELLE SOUS PLAN DE TRAVAIL
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Table des matières . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
W10056407A
Table of Contents
WARNING
Tip Over Hazard
Do not use dishwasher until completely installed.
Do not push down on open door.
Doing so can result in serious injury or cuts.
You can be killed or seriously injured if you don't immediately
You
can be killed or seriously injured if you don't
follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
DISHWASHER SAFETY
You Need to:
Slowly open dishwasher door while someone grasps the
rear of the dishwasher. Remove shipping materials, drain
hose and lower rack. Close dishwasher door until latched.
Observe all governing codes and ordinances.
Install this dishwasher as specified in these instructions.
Installation should be performed by a qualified service
technician. The dishwasher must be installed to meet all
electrical and plumbing national and local codes and
ordinances.
Installation Instructions
(cont.)
Install the Door Handle (on some models) . . . . . . . . . . . 14
Custom Panel Dimensions . . . . . . . . . . . . . . . . . . . . . . . . 14
Install Custom Panel - Option 1 . . . . . . . . . . . . . . . . . . . . 15
Install Custom Panel - Option 2 . . . . . . . . . . . . . . . . . . . . 16
Choose Attachment Option. . . . . . . . . . . . . . . . . . . . . . . . 17
Move Dishwasher Into Cabinet Opening. . . . . . . . . . . . . 18
Connect to Water Supply . . . . . . . . . . . . . . . . . . . . . . . . . 20
Connect to Drain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Make Direct Wire Electrical Connection. . . . . . . . . . . . . . 21
Secure Dishwasher in Cabinet Opening . . . . . . . . . . . . . 23
Complete Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Check Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
If Dishwasher Does Not Operate . . . . . . . . . . . . . . . . . . . 25
Additional Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Dishwasher Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Tools and Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Location Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Drain Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Water Supply Requirements. . . . . . . . . . . . . . . . . . . . . . . . 6
Electrical Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Prepare Cabinet OpeningExisting Utilities. . . . . . . . . . . 7
Prepare Cabinet OpeningNew Utilities. . . . . . . . . . . . . . 7
Prepare and Route Water Line . . . . . . . . . . . . . . . . . . . . . . 8
Install Drain Hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Install Moisture Barrier (on some models) . . . . . . . . . . . 10
Prepare Dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Make Power Supply Cord Connection. . . . . . . . . . . . . . . 12
Determine Cabinet Opening . . . . . . . . . . . . . . . . . . . . . . . 13
2
Tools and Parts
Gather the recommended tools and parts before starting
installation. Read and follow the instructions provided with
any tools listed here.
All Installations
Tools needed:
*Must be the proper size to connect your household wiring
to 16-gauge wiring in dishwasher
Other useful items you may need:
Parts supplied:
Make sure all these parts are included in the literature package.
Parts needed:
4 #10 x 1/2" wood screws (if installing custom front panels)
Wire stripper
Small
tubing cutter
Electric drill
with 1/2, 3/4
and 1 1/2 hole
saw bits
Pliers
UL listed or CSA
approved twist-on
wire connectors*
5/8 open-end
wrench
Small level
Utility knife
Phillips
screwdriver
Measuring tape
or ruler
10 adjustable wrench
that opens to
1.18 (2.9 cm)
Flat-blade
screwdriver
5/16 and 1/4
nut drivers or
hex sockets
If installing custom front panels,
Torx T15 screwdriver
INSTALLATION REQUIREMENTS
90° Elbow fitting with 3/8
N.P.T. external threads (the
other end must fit your water
supply line)
Teflon
®
tape or pipe
joint compound
Drain hose
2 - Drain hose clamps
(1 large and 1 small)
2 - #10 x 1/2
Phillips-head
screws
Green
Silver
Copper tubing (3/8
O.D. suggested) or
flexible braided
water supply line
For Direct Wire:
use UL listed or
CSA approved
strain relief to
fit 7/8 (2.2 cm)
hole
See Electrical Requirements section
For Power Supply
Cord: use UL
listed power
supply cord kit
marked for use
with dishwasher
Flashlight
Bath towel
Wood block
Shallow pan
3
1 1/2”–2
(38.15.0 cm)
Screw-type
clamps (3 max)
Masking or
duct tape
2 #8x1-3/8 Torx
®
T15 screws 4 #10x3/8 hex-head screws
Bottom sound pad (located
in lower rack)
Moisture barrier tape
Other parts you may also need:
NOTE:
Parts available for purchase in plumbing supply stores.
Check local codes. Check existing electrical supply. See
Electrical Requirements section. It is recommended that
electrical connections be made by a licensed electrical installer.
In addition, for first-time installations
Tools needed:
Parts needed:
Additional parts supplied with top-venting models only:
Additional parts supplied with certain models only:
Make sure all these parts are included in the literature package.
If parts are not included, call 1-800-422-1230.
® Teflon is a registered trademark of E.I. Du Pont de Nemours and Company.
†® TORX is a registered trademark of Acument Intellectual Properties, LLC.
4
Location Requirements
Grounded electrical supply required.
Do not run drain lines, water lines or electrical wiring where
they can interfere with or contact dishwasher motor or legs.
The location where the dishwasher will be installed must
provide clearance between motor and flooring. Motor
should not touch the floor.
Do not install dishwasher over carpeted flooring.
Shelter dishwasher and water lines leading to dishwasher
against freezing. Damage from freezing is not covered by
the warranty.
A side panel kit is available from your dealer for installing
your dishwasher at the end of your cabinetry.
A moisture barrier accessory (Part Number 4396277) is
available from your dealer for installing underneath the
countertop, but is not required. Call 1-800-422-1230 to
order.
Check location where dishwasher will be installed. The
location must provide:
easy access to water, electricity and drain.
convenient access for loading and unloading dishes.
Corner locations require a 2 (5.1 cm) minimum
clearance between the side of the dishwasher door
and the wall or cabinet.
square opening for proper operation and appearance.
cabinet front perpendicular to floor.
level floor. (If floor at front of opening is not level with
floor at rear of opening, shims may be needed to level
dishwasher.)
Helpful Tip: Be sure to accurately measure dimensions
and ensure dishwasher is level if the floor in the
dishwasher opening is uneven (example: Flooring
extends only partway into opening).
NOTE: To avoid shifting during dishwasher operation,
shims must be securely attached to the floor.
If dishwasher will be left unused for a period of time or in a
location where it may be subject to freezing, have it
winterized by authorized service personnel.
Make sure pipes, wires and drain hose are within the
shaded area shown in the Product and Cabinet
Opening Dimensions section.
24
(61 cm)**
34
(86.4 cm)
min*
4
(10.2 cm)
3
(7.6 cm)
24
(61 cm)
1 3/4
(4.4 cm)
1 3/4
(4.4 cm)
Check that all surfaces have no protrusions
that would prohibit dishwasher installation.
10 1/2
(26.7 cm)
2
(5.1 cm)
2 1/2
(6.4 cm)
6 3/4
(17.2 cm)
6 1/4
(15.9 cm)
C
lear
Area
3/4
(1.9 cm)*
*Insulation may be compressed
(not used on all models)
24 1/2
(62.2 cm)
24 7/8
(63.2 cm)
23 7/8
(60.6 cm)
21
(
53.3 cm)
33 7/8
(86 cm) min
.
with wheels
removed
Product and Cabinet Opening Dimensions
NOTE: Shaded area of cabinet walls show where
utility connections may be installed.
*Measured from the lowest point on the
underside of countertop. May be reduced to
33 7/8 (86 cm) by removing wheels from
dishwasher.
**Minimum, measured from narrowest point of
opening.
5
Drain Requirements
A new drain hose is supplied with your dishwasher.
If this is not long enough, use a new drain hose with a
maximum length of 12 (3.7 m) (Part Number 3385556)
that meets all current AHAM/IAPMO test standards, is
resistant to heat and detergent, and fits the 1 (2.5 cm)
drain connector of the dishwasher.
Make sure to connect drain hose to waste tee or disposer
inlet above drain trap in house plumbing and 20
(50.8 cm) minimum above the floor. It is recommended
that the drain hose either be looped up and securely
fastened to the underside of the counter, or be connected
to an air gap.
Make sure to use an air gap if the drain hose is connected
to house plumbing lower than 20 (50.8 cm) above
subfloor or floor.
Use 1/2 minimum I.D. drain line fittings.
If required, the air gap should be installed in accordance
with the air gap installation instructions. When you are
connecting the air gap a rubber hose (not provided) will
be needed to connect to the waste tee or disposer inlet.
Water Supply Requirements
A hot water line with 20-120 psi (138-862 kPa) water
pressure can be verified by a licensed plumber.
120°F (49°C) water at dishwasher.
3/8 O.D. copper tubing with compression fitting or
flexible braided water supply line (Part Number
4396897RP)
NOTE:
1/2 minimum plastic tubing is not recommended.
A 90° elbow with 3/8 N.P.T. external pipe threads on one
end.
Do not solder within 6 (15.2 cm) from water inlet valve.
Use of air gap
Air gap
Electrical Requirements
Be sure that the electrical connection and wire size are
adequate and in conformance with the National Electrical
Code, ANSI/NFPA 70 - latest edition and all local codes and
ordinances.
A copy of the above code standards can be obtained from:
National Fire Protection Association
One Batterymarch Park
Quincy, MA 02269
You must have:
120-volt, 60 Hz, AC-only, 15 or 20 amp, fused electrical
supply.
copper wire only.
We recommend:
a time-delay fuse or circuit breaker.
a separate circuit.
If connecting dishwasher
with a power supply cord:
Use UL listed power supply cord kit (Part Number
4317824) marked for use with dishwasher.
Power supply cord must plug into
a grounded 3 prong outlet, located in
the cabinet next to the dishwasher
opening. Outlet must meet all local
codes and ordinances.
If connecting dishwasher with direct wiring:
Use flexible, armored
or nonmetallic
sheathed, copper wire
with grounding wire
that meets the wiring requirements for your home and
local codes and ordinances.
Use a UL listed or CSA approved strain relief.
6
7
1 1/2
(3.8 cm)
Power Supply Cord-Drill hole
1
Pref rred location
Pref rred location
Preferred location
Optional location
Optional location
Optional location
Drill a 1 1/2 (3.8 cm) hole in cabinet side or rear.
See product and cabinet opening dimensions.
NOTE: A grounded 3 prong outlet is required inside a
cabinet next to the dishwasher cabinet opening.
WARNING
Disconnect electrical power at the fuse box or circuit
breaker box before installing dishwasher.
Failure to do so can result in death or electrical shock.
Electrical Shock Hazard
Disconnect electrical power at the fuse box or circuit
breaker box before installing dishwasher
Disconnect power
1
2
Water line
Cable
Do you already have utility
hookups?
3
Existing utility hookups No existing utility hookups
Yes Follow instructions in the Prepare Cabinet
OpeningExisting Utilities section.
No Follow instructions in the Prepare Cabinet
OpeningNew Utilities section.
Prepare Cabinet Opening—New
Utilities
What type of electrical
connection will you use?
Power Supply Cord:
Follow Option A instructions
Direct Wire:
Follow Option B instructions
Prepare and route the electrical supply
Option A, Power Supply Cord:
6
(15.2
cm)
1
Water line
Cable
Check water and electrical
placement
If the water line and the cable extend to the locations
shown, proceed to the Install Drain Hose section. If they
do not reach far enough, follow the instructions in the
Prepare Cabinet OpeningNew Utilities section.
Prepare Cabinet Opening—Existing
Utilities
INSTALLATION INSTRUCTIONS
6
(15.2 cm)
Direct WireRoute cable
3
Route cable from power supply through cabinet hole (cable
must extend to the right front side of cabinet opening).
Tape cable to the floor in area shown. This will prohibit
cable from moving when dishwasher is moved into
cabinet opening.
Wood
cabinet
Metal
cabinet
Power Supply CordPrepare hole
2
Wood cabinet: Sand hole until smooth.
Metal cabinet: Cover hole with grommet included with
power supply cord kit.
1/2
(1.3 cm)
Drill hole
1
Preferred locations
Preferred locations
Preferred locations
Optional locations
Optional locations
Optional locations
Drill a 1/2 (1.3 cm) hole in the cabinet side or rear.
Helpful Tip: Routing the water line through the left side
of cabinet opening will make water connection easier.
Hot water line
2
Measure water supply line
Measure overall length of copper tubing or flexible
braided water supply line. Attach to the hot water line
using a connection configuration that is in compliance
with local codes and ordinances. The water line to the
dishwasher should have a manual shutoff valve.
Prepare and Route Water Line
3/4
(1.9 cm)
Direct WireDrill hole
1
Preferred location
Preferred location
Optional location
Drill a 3/4 (1.9 cm) hole in right-hand cabinet side or rear.
See product and cabinet opening dimensions.
Wood
cabinet
Metal
cabinet
Direct WirePrepare hole
2
Wood cabinet: Sand the hole until smooth.
Metal cabinet: Cover hole with grommet (not provided).
Helpful Tip: Wiring the dishwasher will be easier if you
route the cable into the cabinet opening from the right side.
Option B, Direct Wire:
8
9
Flush water supply line
4
Slowly turn water shutoff valve to ON position. Flush
water into a shallow pan until clear to get rid of particles
that could clog the inlet valve. Turn shutoff valve to
OFF position.
Drill hole
1
1-1/2
(3.8 cm)
If needed, drill a 1 1/2 (3.8 cm) diameter hole in cabinet
wall or side of the opening closest to the sink.
Connect drain hose to waste tee or waste disposer
using one of the following options:
Option A, Waste disposer no air gap
Option B, No waste disposer no air gap
Option C, Waste disposer with air gap
Option D, No waste disposer with air gap
Connect drain hose
3
Install Drain Hose
IMPORTANT: Always use a new drain hose. Check local
codes to determine if an air gap is required.
Large silver
drain hose clamp
Drain hose
Drain trap
Drain trap
Disposer inlet
Disposer inlet
Waste disposer no air gap
1. Using a hammer and screwdriver,
knock plug into disposer.
2. Use needle nose pliers to remove
plug.
3. Attach drain hose to disposer inlet
with large silver drain hose clamp
(provided). Use pliers to squeeze
clamp open and move into position.
1
3
2
Option A, Waste disposer – no air gap
Drain hose
Route drain hose
2
Route drain hose as shown through hole in cabinet to the
front center of opening where drain connection will be
made. Tape drain hose to the floor in area shown. This will
prohibit it from moving when dishwasher is moved into
cabinet opening.
IMPORTANT: The drain hose connection of the disposer or
a waste tee must be made before the drain trap and at
least 20 (50.8 cm) above the floor where the dishwasher
will be installed.
Helpful Tip: To reduce vibration of the hose, keep the hose
away from the floor.
Route water supply line
3
Slowly route water supply line through hole in cabinet.
(If using copper tubing, it will bend and kink easily, so be
gentle.) It should be far enough into the cabinet opening
to connect it to the dishwasher inlet on the front left
side of the dishwasher.
Air gap
Large silver drain
hose clamp
(provided)
Drain trap
Air gap
Large silver drain
hose clamp
Drain hose
Drain trap
Rubber hose
connector
Screw-type clamps
Screw-type clampsScrew-type clamps
Waste tee
Waste tee
No waste disposer with air gap
1. Connect black end of drain hose to air
gap and cut if needed. (Do not cut
ribbed section.)
2. Attach drain hose to air gap with large
silver drain hose clamp (provided).
Use pliers to squeeze clamp open and
move into position. If the drain hose
was cut, use a 1 1/2 to 2(3.8 to 5 cm)
screw-type clamp (not provided).
3. Use a rubber hose (not provided) with
screw-type clamps (not provided) to
connect from waste tee to air gap.
Air gap
Large silver drain
hose clamp
(provided)
Disposer inlet
Air gap
Large silver drain
hose clamp
Drain hose
Drain trap
Rubber hose
connector
Disposer inlet
Waste disposer with air gap
Screw-type clampsScrew-type clampsScrew-type clamps
1
2
3
4
5
Black end
1
2
3
Black end
Option C, Waste disposer with air gap
Option D, No waste disposer with air gap
Screw-type
clamp
Drain trap
Large silver
drain hose clamp
Drain hose
Drain trap
Waste tee
Waste tee
No waste disposer no air gap
Waste tee
1. Connect black end of of drain hose to
waste tee and cut if needed.
(Do not cut ribbed section.)
2. Attach black end of drain hose to waste
tee with a large silver drain hose clamp
(provided). Use pliers to squeeze clamp
open and move into position. If the drain
hose was cut use a 1 1/2 to 2 (3.8 to
5 cm) screw-type clamp (not provided).
1
2
Black end
Option B, No waste disposer no air gap
1. Using a hammer and screwdriver,
knock plug into disposer.
2. Use needle nose pliers to remove
plug.
3. Connect black end of drain hose to air
gap and cut if needed. (Do not cut
ribbed section.)
4. Attach drain hose to air gap with large
silver drain hose clamp (provided).
Use pliers to squeeze clamp open and
move into position. If the drain hose
was cut, use a 1 1/2 to 2(3.8 to
5 cm) screw-type clamp (not
provided).
5. Use a rubber hose (not provided) with
screw-type clamps (not provided) to
connect from air gap to disposer inlet.
Install moisture barrier
(on some models)
Moisture
barrier
1. Make sure the area under the cabinet is clean and dry
for installation of the moisture barrier.
2. Remove the backing of the moisture barrier and apply
to underside of the countertop along the front edge of
the counter.
Install Moisture Barrier
(on some models)
10
11
Apply Teflon
®
tape
or pipe joint compound
3
Coarse threads Coarse threads
Apply Teflon
®
tape or pipe joint compound to 90˚ elbow
fitting (not provided). Wrap tape around coarse threads
two to four times to prohibit leaks.
Remove terminal box cover
5
Using a 1/4 hex head socket, nut driver or Phillips
screwdriver, remove terminal box cover. Retain for
later use.
Connect 90° elbow fitting to
water inlet valve
4
Connect 90° elbow fitting to water inlet valve. Using a
wrench, tighten elbow until snug, and be sure that it
faces to the rear.
Excessive Weight Hazard
Use two or more people to move and install
dishwasher.
Failure to do so can result in back or other injury.
WARNING
WARNING
Tip Over Hazard
Do not use dishwasher until completely installed.
Do not push down on open door.
Doing so can result in serious injury or cuts.
Prepare Dishwasher
Put dishwasher on its back
1
Helpful Tip: Place cardboard under dishwasher until installed
in cabinet opening to avoid damaging floor covering. Do not
use door panel as a work table without first covering with a
towel to avoid scratching the door panel.
Using two or more people, grasp sides of dishwasher door
frame and place dishwasher on its back.
Remove panels
2
Using a 1/4 hex head socket, nut driver or Phillips
screwdriver, remove two screws attaching access panel
and lower panel to dishwasher. Do not remove tech
sheet from access panel.
What type of electrical
connection will you use?
Power Supply Cord:
Follow Option A instructions
Direct Wire:
Follow Option B instructions
6
Install a UL listed or CSA approved strain relief. Make sure
screwheads are facing to the left when tightening conduit
nut. Strain relief is provided with the power supply cord kit.
Option A, Power Supply Cord:
Route cord so that it does not touch dishwasher motor
to lower part of dishwasher tub. Pull cord through strain
relief in terminal bow. Take notice when installing or
removing the dishwasher in order to reduce the chance
of damaging the power supply cord.
Select UL listed or CSA approved twist-on wire connectors
(included with power supply cord kit) rated to connect
your household wiring to 16-gauge dishwasher wiring.
1
Power CordRoute cord
into terminal box
WARNING
Electrical Shock Hazard
Electrically ground dishwasher.
Connect ground wire to green ground connector
in terminal box.
Do not use an extension cord.
Failure to follow these instructions can result in
death, fire, or electrical shock.
Remove the green grounding screw and place through
the ring terminal of the green ground wire. Reattach and
tighten the green screw.
Ground
wire
Power Supply Cord
Connect ground wire
2
Ground
wire
Washer
Ground
connector
NOTE: Twist on wire connector. Gently tug on wires to
be sure both are secured.
Connect wires black to black and white to white, using
UL listed or CSA approved twist-on wire connectors
(included with power supply cord kit).
Power CordConnect
remaining wires
3
Make Power Supply Cord Connection
12
Cabinet
opening height
34” (86.4 cm) 1 10
33 7/8” (86.0 cm) remove All the way up
34 1/4 (87 cm) 2 5
34 1/2 (87.6 cm) 3 0
Wheel
position
Number of turns
on front leg
Dishwasher Height Adjustment Chart
13
Terminal box wire:
white
black
ground connector
Power supply wire:
white
black
ground wire
Wiring configuration
If needed, see website for animated representation of
this step. Visit www.kitchenaid.com under FAQ tab.
Tighten strain relief screws to secure cord.
Power Cord - Secure cord
on strain relief
4
Place wires inside terminal box. Insert tabs on left side
of cover. Make sure wires are tucked inside box. Close
cover ensuring wires are not pinched. Use 1/4 nut
driver and previously removed screw to secure cover.
NOTE: Do not plug into outlet until instructed to do so.
Power CordReinstall
terminal box cover
5
Measure height of cabinet opening from underside of
countertop to floor where dishwasher will be installed
(you will need to measure the lowest point on the
underside of the countertop and the highest point on the
floor). Refer to Dishwasher Height Adjustment Chart
for wheel position and the number of turns needed.
Measure cabinet opening
1
Determine Cabinet Opening
NOTE: If the minimum cabinet opening height is less than
34(86.4 cm), the rear wheels can be removed for
additional clearance. This will allow the dishwasher to fit
into a 33 7/8 (86 cm) high cabinet opening, but the
dishwasher will be more difficult to move. (Measurements
are approximate. Wheels and legs are preset at the
factory for 34 1/2 [87.6 cm].)
Turn both leveler legs to the same height. Put wheels in
the required position determined from Dishwasher
Height Adjustment Chart.
Adjust wheels and legs
2
1
2
3
wheel
Built-up floors (Kitchen floor height is higher than
cabinet opening.) Example: Kitchen floor tile does not
extend into cabinet opening. Add shims as needed in the
area shown to bring the dishwasher up to 34 (86.4 cm)
below the countertop.
NOTE: Shims must be securely attached to floor to avoid
movement when the dishwasher is in use.
2-3/4”
(7 cm)
4”
(10.1 cm)
2”
(5 cm
)
Built-up FloorsAdd
shims as needed
3
14
IMPORTANT: Do not scratch the front panel during this
procedure.
Remove the door handle and hardware bag containing
the setscrews and Allen wrench from the cardboard box.
Setscrews are already installed in the handle. Place
handle on mounting studs with the setscrews facing
down. Push the door handle tightly against the door.
Insert the short end of the Allen wrench into the
setscrews. Tighten the setscrews 1/4 turn past snug.
Retain Allen wrench with Installation Instructions.
Install door handle
Mounting stud
Handle
Setscrew
(in bottom
of handle)
Allen wrench
Install the Door Handle
(on some models)
Custom Panel Dimensions
IMPORTANT: You need to know what control panel is on
your dishwasher before you order your custom door
panel.
Follow directions under Option 1 of Install custom
panelsection.
Follow directions in Option 2 of Install custom panel
section.
*
Dishwashers with control panel on
top custom panel dimensions
23 1/2
(59.7 cm)
*30 3/16 (76.7 cm)
3/4 (19.1 mm)
This dimension is for 4 (10.2 cm) toe kick. If the
installation needs a higher toe kick, adjust the height
of the wood panel accordingly. Not recommended for
toe kicks greater than 6 (15.2 cm).
*
Dishwashers with control panel on
front custom panel dimensions
23 3/8
(65.8 cm)
*25 29/32 (65.8 cm)
3/4
(19.1 mm)
This dimension is for 4 (10.2 cm) toe kick. If the
installation needs a higher toe kick, adjust the height
of the wood panel accordingly. Not recommended for
toe kicks greater than 6 (15.2 cm).
*
1/8 (3.2 mm)
1/8
(3.2 mm)
15
(Models KUDS40FVPA, KUDS50FVPA, KUDE60FVPA,
and KUDE70FVPA)
NOTE: The handle for the custom panel is not included.
IMPORTANT: If the handle is attached from the back of
the custom panel, the screw holes should be countersunk
for the screws heads to be flush with the panel. If the
handle is attached to the front of the custom panel, the
screw lengths cannot exceed the panel thickness. For
more information on KitchenAid custom handle selection,
refer to the KitchenAid Catalog, visit
www.kitchenaid.com, or call 1-800-422-1230.
NOTE: A customer-supplied full front panel must weigh
no more than 16 lbs (7.3 kg) and must be made to
specific dimensions. It is recommended that a
cabinetmaker cut the custom panel because of the
precise dimensions needed.
NOTE: All mounting hardware supplied is for a 3/4"
(19.1 mm) thick wood panel. If a thinner wood panel, or
materials other than wood are used, it is the consumers
responsibility to obtain the proper length screws and
adjust the pilot holes accordingly.
IMPORTANT: Use a moisture resistant sealer on both
sides and all edges of the panel to avoid damage from
humidity.
With a TORX
®
screwdriver, remove three screws from both
sides, as shown; hold the outer panel up while removing
the screws. Save screws for reinstallation.
Custom panel installation -
Dishwashers with control
panel on the top
This dimension is for 4 (10.2 cm) toe kick. If the
installation needs a higher toe kick, adjust the height
of the wood panel accordingly. Not recommended for
toe kicks greater than 6 (15.2 cm).
*
1
23 1/2
(59.7 cm)
*30 3/16 (76.7 cm)
3/4 (19.1 mm)
Mark line
3
9 29/32
(25.2 cm)
Top edge
Back
Gently set outer panel aside. Lay the customer-supplied
custom panel face down on a covered, non-scratching
surface.
Dishwashers with control panel on
top custom panel dimensions
2
outer panel
3 screws
per side
Install Custom Panel – Option 1
Measure 9 29/32" (25.2 cm) from top edge and mark a line
on the back of customer-supplied custom panel. Position the
outer panel on the back of the customer-supplied custom
panel as shown, so that the top holes in the outer panel are
on the line, and both panels are centered side to side.
Mark pilot holes
4
Mark pilot
holes
Mark all four hole locations; remove outer panel. Drill 3/32"
pilot holes 1/2" (13 mm) deep in customer-supplied custom
panel. Place the outer panel on the back of the customer-
supplied custom panel; align holes.
16
Install custom panel
8
Customer-supplied
panel
Align top
edges
Drill through
these holes
1-3/8 Screw
Install the two #8-18 x 1 3/8" screws from
the literature package in the top corners of the inner
panel. Tighten the six side screws reinstalled in Step 6.
(Models KUDC03IV and KUDS30IV)
All models require an accessory option to attach custom
panels. Kit Number 8171555 (black), 8171556 (white) or
8171557 (biscuit) are available. To order, call customer
service at 1-800-444-1230.
NOTE: A custom full front panel must weigh no more
than 14 lbs (6.3 kg) and must be made to specific
dimensions. It is recommended that a cabinetmaker cut
the custom panel because of the precise dimensions
needed.
IMPORTANT: Use a moisture resistant sealer on both
sides and all edges of the panel to avoid damage from
humidity.
NOTE: These dimensions are for frameless custom panel
models with a 4 (10.2 cm) console only.
With a TORX
®
screwdriver, remove three screws from
both sides, as shown; hold the outer panel up while
removing the screws. Save screws for reinstallation.
Custom panel installation -
Dishwashers with control
panel on the front
23 3/8
(65.8 cm)
*25 29/32 (65.8 cm)
3/4
(19.1 mm)
This dimension is for 4 (10.2 cm) toe kick. If the
installation needs a higher toe kick, adjust the height
of the wood panel accordingly. Not recommended for
toe kicks greater than 6 (15.2 cm).
*
1/8 (3.2 mm)
1/8
(3.2 mm)
1
Install Custom Panel Option 2
6
(15.2 mm)
Hex Head
Screw
Attach handle
5
Attach outer panel to back of customer-supplied custom
panel with the four #10-16 x 3/8" hex head screws supplied
in the literature package. Attach the handle. The handle
should be centered on the front of the customer-supplied
custom panel in the area shown.
IMPORTANT: Screw heads must be flush with back of
customer-supplied custom panel.
Attach the panel assembly to the door by reinstalling the
three screws on each side; do not tighten completely. This
reinstallation of the three screws will hold the panel
assembly in place on the door frame.
Align the top edge of the customer-supplied custom
panel with the top of the console.
Drill two 3/32" pilot holes 1/2" (13 mm) deep, into the
customer-supplied custom panel, through the holes in the
top corners on the inner panel, as shown.
Attach body panel
6
Customer-supplied
panel
Align top
edges
Reinstall
3 screws
each side
Install custom panel
7
Customer-supplied
panel
Align top
edges
Drill through
these holes
17
Mark pilot holes
3
Mark pilot
holes
Gently set outer panel aside. Lay the cutomer-supplied
custom panel face down on a non-scratching surface.
Position the outer panel on the back of the customer-
supplied custom panel as shown; make sure top edge of
the outer panel is aligned with the top edge of the
customer-supplied custom panel, and both panels are
centered side to side.
Mark all four hole locations; remove outer panel and drill
3/32" pilot holes 1/2" (13 mm) deep, in customer-supplied
custom panel. Place the outer panel on the back of the
customer-supplied custom panel and align holes. Attach
outer panel to back of customer-supplied custom panel
with four #10 x 1/2" wood screws (not supplied). If the
customer-supplied custom panel is less than 3/4" (1.9 cm)
thick where the screws are attached, shorter screws maybe
required.
Attach the panel assembly to the door by reinstalling the
three screws on each side.
Dishwashers with control panel on
front custom panel dimensions
2
outer panel
3 screws
per side
Attach body panel
4
Customer-supplied
panel
Align top
edges
Reinstall
3 screws
each side
Choose Attachment Option
WARNING
Excessive Weight Hazard
Use two or more people to move and install
dishwasher.
Failure to do so can result in back or other injury.
Using two or more people, stand the dishwasher up.
brackets
Countertop attachment
IMPORTANT: The dishwasher must be secured to the
cabinet. There are two brackets on top of the dishwasher
that can be attached to the countertop if it is wood,
laminate or other similar surfaces. If your countertop is
marble, granite or other hard surface the brackets may
be moved to the sides of the dishwasher.
NOTE: Do not attach the dishwasher. This will be done
later.
tabs
Remove brackets from the top
1
To remove the brackets from the top, flatten tab at back
of brackets with pliers, and pull the brackets out of the
slots.
Option 1, Countertop attachment:
Option 2, Dishwasher side attachment:
18
plastic
button
Insert plastic buttons
3
Push the plastic buttons out of the side of the tub.
NOTE: Save the buttons to cover the holes after
dishwasher is installed.
score line
Break end of bracket
2
Break off the end of the bracket along the scored line.
With another person holding the rear of the dishwasher
to keep it from tipping, open dishwasher door and place
towel over pump assembly and spray arm of dishwasher.
This will keep screws from falling into pump area when
you are securing dishwasher to cabinet.
bend
tabs
Reinstall bracket
4
Push bracket into slot on the side of dishwasher, and
bend tab in toward the side of the dishwasher so that it
keeps the bracket in place. Repeat this step for the other
side of the dishwasher.
NOTE: Do not attach the dishwasher. This will be done
later.
Move Dishwasher into Cabinet
Opening
Using two or more people, stand dishwasher upright.
NOTE: Do not install kickplate until instructed.
Stand dishwasher upright
1
Move dishwasher close to
cabinet opening
2
Water
line
Cable
Drain
hose
Direct wire
only
IMPORTANT: Double check correct placement of utilities.
Grasp the sides of the dishwasher at the edges of the
door panel. Tilt dishwasher backwards on wheels and
move dishwasher close to cabinet opening.
NOTE: Do not push on the front of the panel or on the
console. Panel or console may dent.
Helpful Tip: Temporarily tape utilities to the floor in the
locations shown to prohibit them from moving when
dishwasher is moved into the cabinet opening.
WARNING
Excessive Weight Hazard
Use two or more people to move and install
dishwasher.
Failure to do so can result in back or other injury.
19
With another person holding the dishwasher to avoid it
from tipping, open and close the door a few times. If the
door closes or falls open under its own weight, the door
tension will need to be adjusted.
4
Open and close door
screw
tensioner
spring
Closes too quickly —
Decrease spring tension
5
When door is unlatched, and door opens by itself, move
the tensioner to a lower numbered hole and replace the
screw. Reattach door spring to rear leg.
Door falls open
Increase spring tension
6
IMPORTANT: If wheels were removed, protect the floor
when moving the dishwasher. Slowly move dishwasher
completely into cabinet opening. Do not kink or pinch
water line, drain hose, power supply cord or direct wire
between dishwasher and cabinet. Remove cardboard
from under dishwasher.
NOTE: It is all right if dishwasher fits tightly into cabinet
opening. Do not remove insulation blanket the blanket
reduces the sound level.
NOTE: If using power cord, make sure to route end
through hole in cutout before sliding into cabinet opening.
Move dishwasher into
cabinet opening
7
Insulation
blanket
Align front of dishwasher door panel with front of
cabinet doors. You may need to adjust alignment to be
even with your cabinets.
Align front of dishwasher
with front of cabinet doors
8
NOTE: Tensioners on both sides of dishwasher should
be secured at same holes.
To adjust the door spring tension, unhook the spring
from the rear leg of dishwasher.
Using a 5/16" nut driver or hex socket, remove the screw
from the tensioner.
The screw can be put into one of three holes , ,
in the front leg of dishwasher. If the door closes by itself,
move the tensioner to a higher number hole and replace
screw. Reattach door spring to rear leg.
NOTE: Tensioners on both sides of dishwasher should be
secured at same holes.
Check that water line is on the left side of opening and
drain hose is near the center of the cabinet opening.
Check water and drain
hose position
3
20
Slide nut and ferrule
onto tubing
1
Ferrule
Nut
Connect to Water Supply
Copper tubing only: Slide nut then ferrule onto copper
tubing about 1 (2.5 cm).
NOTE: To avoid vibration during operation, route the
water supply line so that it does not touch the
dishwasher base, frame or motor.
Tighten copper or braided
tubing connection
3
Hold the 90° elbow fitting still with one adjustable wrench
and tighten the nut with second adjustable wrench.
Helpful Tip: Use a 5/8 open ended wrench for easier
access to tighten connection.
Connect water supply
using copper or flexible line
2
Copper tubing only: Put the tubing into the 90° elbow
fitting as far as it will go (the copper tubing bends and
kinks easily). Slide the nut and ferrule forward and start
the nut onto the elbow threads.
Flexible braided connection: Secure nut to elbow using
5/8 open ended wrench or adjustable wrench.
NOTE: Do not use Teflon
®
tape with compression fittings.
9
Check for plumb and
adjust legs if needed
Check that leveling legs are firmly against the floor.
Close and latch the door, and place level against the
front panel. Check that dishwasher is centered from front
to back in the opening. If needed, adjust leveling leg until
dishwasher is plumb. Repeat for other side of dishwasher.
Helpful Tip: Push up on front of dishwasher to raise
dishwasher off the ground to adjust front legs. With
some installations, it may be easier to adjust the front leg
using the 3/16 hex head socket or adjustable wrench.
Preferred method Optional method
Check level side to side and
adjust legs if needed
10
Place level against top front opening of tub. Check that
dishwasher is level from side to side. If dishwasher is not
level, adjust front legs up or down until dishwasher is
level.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52

KitchenAid KUDC03IV User manual

Category
Dishwashers
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages