RIDGID HC-300 User manual

Hole Cutting Tools

OPERATOR’S

MANUAL

• Pour français voire page 15

• Para el castellano vea la

página 31

HC-450

HC-300

WARNING!

For your own safety, read this

Operator’s Manual carefully

before assembling or operat-

ing this unit.

HC-450/HC-300 Hole Cutting Tools

Ridge Tool Company • Elyria, Ohio • U.S.A.

ii

Table of Contents

General Safety Information

Work Area Safety........................................................................................................................................................2

Electrical Safety..........................................................................................................................................................2

Personal Safety...........................................................................................................................................................2

Tool Use and Care......................................................................................................................................................3

Service........................................................................................................................................................................3

Specific Safety Information

Tool Safety..................................................................................................................................................................4

Model HC-450 Description, Specifications and Accessories

Description..................................................................................................................................................................4

Specifications..............................................................................................................................................................4

Standard Equipment...................................................................................................................................................4

Accessories.................................................................................................................................................................4

Inspect Hole Cutting Tool.............................................................................................................................................5

Setup Instructions

Model HC-450.............................................................................................................................................................5

Operating Instructions

Model HC-450.............................................................................................................................................................7

Locating Level Vial Instructions..................................................................................................................................8

Model HC-300 Description, Specifications and Accessories

Description..................................................................................................................................................................8

Specifications..............................................................................................................................................................9

Standard Equipment...................................................................................................................................................9

Accessories.................................................................................................................................................................9

Inspect Hole Cutting Tool.............................................................................................................................................9

Setup Instructions

Model HC-300.............................................................................................................................................................9

Operating Instructions

Model HC-300...........................................................................................................................................................12

Maintenance

Motor Brush Replacement........................................................................................................................................13

Service and Repair......................................................................................................................................................13

Lifetime Warranty .........................................................................................................................................Back Cover

Hole Cutting Tools

Record Serial Number below and retain product serial number which is located on nameplate.

Serial

No.

HC-450/HC-300

Hole Cutting Tools

Model HC-450

Model HC-300

HC-450/HC-300 Hole Cutting Tools

5. When operating a power tool outside, use an

outdoor extension cord marked “W-A” or “W”.

These cords are rated for outdoor use and reduce

the risk of electrical shock.

6. Use only three-wire extension cords which

have three-prong grounding plugs and three-

pole receptacles which accept the machines

plug. Use of other extension cords will not ground

the tool and increase the risk of electrical shock.

7. Use proper extension cords. (See chart.) Insuf-

ficient conductor size will cause excessive voltage

drop, loss of power and overheating.

8. Before using, test the Ground Fault Circuit

Interrupter (GFCI) provided with the power cord

to insure it is operating correctly. GFCI reduces

the risk of electrical shock.

9. Extension cords are not recommended unless

they are plugged into a Ground Fault Circuit

Interrupter (GFCI) found in circuit boxes or out-

let receptacles. The GFCI on the machine power

cord will not prevent electrical shock from the

extension cords.

10. Keep all electric connections dry and off the

ground. Do not touch plug with wet hands.

Reduces the risk of electric shock.

Personal Safety

1. Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use tool while tired or under the influ-

ence of drugs, alcohol, or medications. A

moment of inattention while operating power tools

may result in serious personal injury.

2. Dress properly. Do not wear loose clothing or

jewelry. Contain long hair. Keep your hair,

clothing, and gloves away from moving parts.

Loose clothes, jewelry, or long hair can be caught

in moving parts.

3. Avoid accidental starting. Be sure switch is

OFF before plugging in. Carrying tools with your

finger on the switch or plugging in tools that have

the switch ON invites accidents.

Ridge Tool Company • Elyria, Ohio • U.S.A.

2

General Safety Information

WARNING! Read and understand all instructions.

Failure to follow all instructions listed

below may result in electric shock, fire,

and/or serious personal injury.

SAVE THESE INSTRUCTIONS!

Work Area Safety

1. Keep your work area clean and well lit. Cluttered

benches and dark areas invite accidents.

2. Do not operate power tools in explosive atmos-

pheres, such as in the presence of flammable

liquids, gases, or dust. Power tools create sparks

which may ignite the dust or fumes.

3. Keep bystanders, children, and visitors away

while operating a power tool. Distractions can

cause you to lose control.

Electrical Safety

1. Grounded tools must be plugged into an outlet,

properly installed and grounded in accordance

with all codes and ordinances. Never remove

the grounding prong or modify the plug in any

way. Do not use any adapter plugs. Check with

a qualified electrician if you are in doubt as to

whether the outlet is properly grounded. If the

tools should electrically malfunction or break down,

grounding provides a low resistance path to carry

electricity away from the user.

2. Avoid body contact with grounded surfaces

such as pipes, radiators, ranges and refrigera-

tors. There is an increased risk of electrical shock

if your body is grounded.

3. Don’t expose power tools to rain or wet condi-

tions. Water entering a power tool will increase the

risk of electrical shock.

4. Do not abuse cord. Never use the cord to carry

the tools or pull the plug from an outlet. Keep

cord away from heat, oil, sharp edges or moving

parts. Replace damaged cords immediately.

Damaged cords increase the risk of electrical shock.

Minimum Wire Gauge for Cord Set

Nameplate

Amps

Total Length (in feet)

0 – 25 26 – 50 51 – 100

0 – 6 18 AWG 16 AWG 16 AWG

6 – 10 18 AWG 16 AWG 14 AWG

10 – 12 16 AWG 16 AWG 14 AWG

12 – 16 14 AWG 12 AWG

NOT RECOMMENDED

Grounding prong

Cover of

grounded

outlet box

Grounding prong

Ridge Tool Company • Elyria, Ohio • U.S.A.

3

4. Remove adjusting keys or switches before

turning the tool ON. A wrench or a key that is left

attached to a rotating part of the tool may result in

personal injury.

5. Do not overreach. Keep proper footing and

balance at all times. Proper footing and balance

enables better control of the tool in unexpected

situations.

6. Use safety equipment. Always wear eye pro-

tection. Dust mask, non-skid safety shoes, hard

hat, or hearing protection must be used for appro-

priate conditions.

7. Wear hearing protectors, ear plugs or muffs

when using tool. Noise level may affect hearing

with prolonged use.

Tool Use and Care

1. Use clamp or other practical way to secure and

support the workpiece to a stable platform.

Holding the work by hand or against your body is

unstable and may lead to loss of control.

2. Do not force tool. Use the correct tool for your

application. The correct tool will do the job better

and safer at the rate for which it is designed.

3. Do not use tool if switch does not turn it ON or

OFF. Any tool that cannot be controlled with the

switch is dangerous and must be repaired.

4. Disconnect the plug from the power source

before making any adjustments, changing

accessories, or storing the tool. Such preven-

tive safety measures reduce the risk of starting the

tool accidentally.

5. Store idle tools out of the reach of children and

other untrained persons. Tools are dangerous in

the hands of untrained users.

6. Maintain tools with care. Keep cutting tools

sharp and clean. Properly maintained tools with

sharp cutting edges are less likely to bind and are

easier to control.

7. Check for misalignment or binding of moving

parts, breakage of parts, and any other condi-

tion that may affect the tool's operation. If dam-

aged, have the tool serviced before using. Many

accidents are caused by poorly maintained tools.

8. Use only accessories that are recommended by

the manufacturer for your model. Accessories

that may be suitable for one tool may become haz-

ardous when used on another tool.

9. Keep handles dry and clean; free from oil and

grease. Allows for better control of the tool.

Service

1. Tool service must be performed only by quali-

fied repair personnel. Service or maintenance

performed by unqualified repair personnel could

result in injury.

2. When servicing a tool, use only identical

replacement parts. Follow instructions in the

Maintenance Section of this manual. Use of

unauthorized parts or failure to follow mainte-

nance instructions may create a risk of electrical

shock or injury.

Specific Safety Information

WARNING! Read and follow safety labels on the tool!

Know the location and function of all con-

trols before using this hole cutting tool.

HC-450/HC-300 Hole Cutting Tools

▲ WARNING

Clothing/gloves can be caught in moving parts.

Fingers, hands, arms or other body parts can be

cut, crushed or broken.

• Keep fingers and hands away from cutter blade.

• Do not reach across cutter or pipe because cloth-

ing can be drawn into moving parts.

• Do not disconnect or block switch.

• Keep switch in working order.

• When cutting into existing system, pipe must be

drained and de-pressurized.

• Wear safety glasses and ear protection.

• Test Ground Fault Circuit Interrupter (GFCI) to

insure proper operation.

READ ABOVE WARNING CAREFULLY!

Tool Safety

1. Hole Cutting Tools are made to cut holes in

pipe. Follow instructions in Operator’s Manual

on proper use. Other uses may increase the risk

of injury.

2. To prevent entanglement do not reach across

the hole saw or wear loose cloth gloves.

Because this tool has high torque, clothing can

entangle with enough force to crush or break bone.

3. Keep fingers and hands away from the hole

saw blade. Reduces the risk of being cut.

4. Secure the hole cutting tool properly to the pipe.

Carefully follow set-up instructions. Position the

electric cord clear of the base and hole saw.

Improper set-up increases the risk of injury.

5. Do not use dull, bent, or damaged hole saws or

arbors. Less likely to bind and lose control.

6. When cutting into an existing system, the pipe

must be drained and de-pressurized. Reduces

the risk of electrical shock.

Model HC-450 Description,

Specifications and Accessories

Description

The RIDGID Model HC-450 Hole Cutting Tool is

designed to cut holes up to 4

3

/

4

″ into steel pipe. The

multiple hole sizes allow the use of Mechanical T’s

®

,

Hookers

®

, Vic-O-Lets™, and other fittings for branch-

ing unpressurized pipe lines.

The HC-450 has a

5

/

8

″ capacity drill chuck to accom-

modate all sizes of hole saws and hole saw arbors.

An integral motor and gear reduction optimizes perfor-

mance of large diameter hole saws. A unique two-

feed handle and switch actuation allows the operator

to use the Hole Cutting Tool from either the left or

right side. A rotating leveling vial in the base allows

repeated holes to line up. Only 12″ high, the compact

design, allows the HC-450 to be used in tight quarters

or above installed pipe close to ceilings.

NOTE! Mechanical T’s, Hookers, and Vic-O-Lets are reg-

istered trademarks of Victaulic Tool Company

WARNING

The HC-450 is not a Hot Tapping Tool. Care must

be taken to ensure the system is drained and de-

pressurized to prevent serious injury and/or prop-

erty damage!

Ridge Tool Company • Elyria, Ohio • U.S.A.

4

Specifications

Cutting Capacity............Up to 4

3

/

4

″ (120mm)

Pipe Mounting

Capacity ........................1

1

/

4

″ - 8″ (30mm-200mm)

Drill Chuck Capacity......

1

/

16

″ -

5

/

8

″ (2mm-16mm)

Drill Chuck Speed..........110 RPM

Motor Horsepower.........1.2 HP

Current Draw Rating......12 Amps @ 115V

Dimensions

Height - “A”....................11.5″ (29cm)

Length - “B” ...................17″ (43cm)

Width - “C”.....................17″ (43cm)

Weight............................42 lbs. (19Kg)

Standard Equipment

• Hole Cutting Tool

• Chuck Key

•

5

/

8

″ Hole Saw Arbor w/Backing Plate and

1

/

4

″ Pilot

Drill

Accessories

• Hole saws and arbors

• Integral hole saws w/arbors

• Carrying Case

HC-450/HC-300 Hole Cutting Tools

Figure 1 – Dimension A & C

C

A

Ridge Tool Company • Elyria, Ohio • U.S.A.

5

Inspect Hole Cutting Tool

WARNING

To prevent serious injury, inspect your Hole

Cutting Tool on a regular basis. The following

inspection procedures should be performed

before each use of the tool:

1. Inspect the power cord and plug for damage. If the

grounding prong is missing or the cord or GFCI is

damaged, do not use the tool until the cord has

been replaced.

2. Make sure the switches turn the tool ON and OFF.

If broken, do not use until they are replaced.

3. Inspect the power drive for any broken, missing,

misaligned, or binding parts as well as any condi-

tions, which may affect the safe and normal opera-

tion of the tool. If any of these conditions are

HC-450/HC-300 Hole Cutting Tools

Figure 2 – Dimension B

Figure 3 – HC-450 with Standard Equipment

B

present, do not use the tool until the problem has

been repaired. Do not use dull, bent, or damaged

hole saws or arbors.

4. Test the Ground Fault Circuit Interrupter (GFCI) to

insure it is operating correctly. When test button is

pushed in, the indicator light should go OFF.

Reactivate by pushing the reset button in. If the indi-

cator light goes ON, the tool is ready to use. If bro-

ken, do not use the tool until it is replaced.

5. Clean any oil, grease, or dirt from the handles.

This reduces the risk of injury due to the tool slip-

ping from your grip.

6. Use only accessories recommended for your tool.

Accessories used for other tools may be haz-

ardous when used on a hole saw and lead to seri-

ous injury.

7. Inspect the cutting edges of your hole saws. If nec-

essary, replace prior to using in your hole-cutting

tool. Dull or damaged cutting edges can lead to

injury, tool breakage, or excessive heat buildup in

the workpiece and the tool.

Set-Up Instructions

Model HC-450

WARNING

When setting up the hole saw, it should be

unplugged and the switch should be in the OFF

position. To prevent serious injury the tool must

be properly set up.

1. Determine the size and location of hole to be cut.

Follow coupling manufacturer’s recommendations

for hole size to coupling size.

2. Select hole saw and arbor to correct hole size.

Integral arbor hole saws are recommended to

reduce chatter. See Table 1 for ordering information.

Hole Saw Ordering Information – Table #1

Hole Diameter

Hole Arbor Integral

Saw Cat. Saw

Inches mm Cat. No. No. w/Arbor

2 51 52865 53080 56902

2

1

/

2

64 52895 53080 56907

2

3

/

4

70 52910 53080 56912

3

1

/

2

89 52940 59502 56917

4

1

/

2

114 52980 59502 56922

NOTE! 53080 Arbor is

5

/

8

″ Hex; requires

5

/

8

″ Chuck.

59502 Arbor and backing plate is for hole saws

larger than 3″.

3. Place HC-450 on a bench or ground to install hole

saw and arbor into drill chuck.

4. The

1

/

4

″ pilot drill is recommended for pipe that is

installed. If pilot is used make sure it is tight in

arbor and exposed no more than

3

/

8

″.

NOTE! Pilot drills are recommended when cutting holes

in installed systems.

5. Ensure chain assembly and swivel handle are in

working order and free to move.

6. Make sure there is adequate clearance to mount

and position the HC-450.

WARNING

When cutting into an existing system, the pipe

must be drained and depressurized. Do not use in

the presence of flammable liquids, vapors or dust.

7. Lift HC-450 using front and rear carrying handles.

Rear handle can be used for a rope and pulley sys-

tem when working on existing overhead pipe. (See

Figure 4.) Do not lift HC-450 above your shoulder.

(Figure 5)

8. Mount unit in the proximity to hole location.

NOTE! If hole location is on the bottom or sides of pipe,

place unit on top of pipe. Put chain around pipe

and place chain pins into base latch. (See Figure 6.)

WARNING

To prevent cord damage and electrical shock

position electrical cord away from the base of the

tool.

9. Fully tighten chain when pilot drill or saw is over the

hole location. To move unit, loosen chain swivel

handle half a rotation and slide or rotate unit.

Ridge Tool Company • Elyria, Ohio • U.S.A.

6

HC-450/HC-300 Hole Cutting Tools

Figure 4 – Carrying the HC-450

Figure 6 – HC-450 Base Latch

Figure 5 – DO NOT lift HC-450 above your shoulders.

May result in loss of balance.

Base Chain

Latch

Ridge Tool Company • Elyria, Ohio • U.S.A.

7

WARNING

Unit stability must be maintained using either

front or rear carrying handles.

10. Secure the unit in the final location. The HC-450

will operate at all angles relative to the vertical or

horizontal pipe. (See Figure 7.)

11. By using either feed handle, raise the hole saw to

the pipe.

12. Plug the hole-cutting tool into the electrical outlet,

making sure to position the power cord along the

clear path. If the power cord does not reach the

outlet, use an extension cord in good condition.

WARNING

To avoid electric shock and electrical fires,

never use and extension cord that is damaged or

does not meet the following requirements:

• The cord has a three-prong plug similar to

shown in Electrical Safety.

• The cord is rated as “W” or “W-A” if being used

outdoor.

• The cord has a wire thickness gauge that does

not exceed 14 AWG if shorter than 30 feet or 12

AWG if 30 feet or longer. If the cord is too long

or if the wire thickness is too small, the cord

may overheat, melting the cord’s insulation or

causing nearby objects to ignite.

Operating Instructions

Model HC-450

WARNING

Do not use a hole-cutting tool without proper

eye protection.

1. The HC-450 is actuated by depressing one of the

lock out switches located in the front carrying

handle. (See Figure 8.)

2. With one hand on a feed handle and the other

hand on a switch, feed the hole saw into the pipe.

WARNING

Keep fingers and hands away from the saw

blade. Do not reach across the hole saw or wear

loose gloves that may become entangled and

cause serious injury.

3. Rotate the feed handle to apply downward pres-

sure on the hole saw.

WARNING

Do not overfeed saw while cutting. Doing so will

result in premature saw failure and possible

serious injury.

4. After completing the hole cut, retract the saw from

the pipe by turning feed wheel clockwise.

NOTE! When branching off an existing system, use a

hole saw with the

1

/

4

″ pilot drill. The pilot drill

helps retain the pipe slug in the hole saw.

5. Turn unit OFF by releasing the actuator switch and

let hole saw come to a complete stop.

6. Remove unit by unclamping chain and using both

front and rear carrying handles.

7. Brush away all metal chips created by the hole saw

from the area around the hole.

HC-450/HC-300 Hole Cutting Tools

Figure 7 – HC-450 on a Horizontal Cut

Figure 8 – Model HC-450 Lock Out Switches

Ridge Tool Company • Elyria, Ohio • U.S.A.

8

Locating Level Vial

Instructions

The rear base of the HC-450 Hole Cutting Tool hous-

es a level vial. This vial is used to ensure that series

of holes align. (See Figure 9.)

In the event that the hole location is angled by a cer-

tain amount, the vial can be rotated within the base to

reflect the deviated angle.

In new pipe installation, the vial can be pre-set and

used to repeat hole orientation. As long as the vial is

showing level, the hole angles will align.

Model HC-300 Description,

Specifications and Accessories

Description

The RIDGID Model HC-300 Hole Cutting Tool is

designed to cut holes up to 3″ diameter into steel pipe.

The multiple hole size allows the use of Mechanical

T’s

®

, Hookers

®

, Vic-O-Lets™, Weld-O-Let™ and other

fittings for branching unpressurized pipelines.

The HC-300 features a

1

/

2

″ capacity chuck to accom-

modate all size of holes up to 3″ diameter and stan-

dard hole saw arbors up to

7

/

16

″ Hex (

1

/

2

″ chuck size).

An integral motor and gear reduction optimizes the

performance and saw life in the capacity range. A sin-

gle feed handle and ON/OFF switch allows for easy

operation. The compact two-piece design allows the

HC-300 to be used in tight quarters and difficult-to-

reach locations.

NOTE! Mechanical T’s, Hookers, and Vic-O-Lets are reg-

istered trademarks of Victaulic Tool Company.

WARNING

The HC-300 is not a hot tapping tool. Care must

be taken to ensure the system is drained and

de-pressurized to prevent serious injury and/or

property damage.

HC-450/HC-300 Hole Cutting Tools

Figure 9 – Model HC-450 Level Vial

Figure 11 – Model HC-300 Front View

Figure 10 – Model HC-300 Rear View

Figure 12 – Model HC-300 Isometric

Ridge Tool Company • Elyria, Ohio • U.S.A.

9

Specifications

Cutting Capacity............Up to 3″ (76mm)

Pipe Mounting

Capacity ........................1

1

/

4

″ - 8″ (30mm-200mm)

Drill Chuck Capacity......

1

/

16

″ -

1

/

2

″ (2mm-13mm)

Drill Chuck Speed..........360 RPM

Motor Horsepower.........1.2 HP

Current Draw Rating......11 Amps @ 115V

Dimensions

Height............................12.8″ (32.5 cm)

Length ...........................11.9″ (30.2 cm)

Width.............................13.2″ (33.4 cm)

Total Weight..................31 lbs. (14 kg)

Base ...........................10 lbs. (4.5 kg)

Motor Assy. ................21 lbs. (9.5 kg)

Standard Equipment

• Hole Cutting Tool (Base and Motor Assembly)

• Chuck Key

Accessories

• Hole Saws Arbors

• Hole Saws

• Carrying Case

Inspect Hole Cutting Tool

WARNING

To prevent serious injury, inspect your Hole

Cutting Tool on a regular basis. The following

inspection procedures should be performed

before each use of the tool:

1. Inspect the power cord and plug for damage. If the

grounding prong is missing or the cord or GFCI is

damaged, do not use the tool until the cord has

been replaced.

2. Make sure the switches turn the tool ON and OFF.

If broken, do not use until they are replaced.

3. Inspect the hole cutting tool for any broken, miss-

ing, misaligned, or binding parts as well as any

conditions, which may affect the safe and normal

operation of the tool. If any of these conditions are

present, do not use the tool until the problem has

been repaired. Do not use dull, bent, or damaged

hole saws or arbors.

4. Test the Ground Fault Circuit Interrupter (GFCI) to

insure it is operating correctly. When test button is

pushed in, the indicator light should go OFF.

Reactivate by pushing the reset button in. If the

indicator light goes ON, the tool is ready to use. If

broken, do not use the tool until it is replaced.

5. Clean any oil, grease, or dirt from the handles.

This reduces the risk of injury due to the tool slip-

ping from your grip.

6. Use only accessories recommended for your tool.

Accessories used for other tools may be hazardous

when used on a hole saw and lead to serious

injury.

7. Inspect the cutting edges of your hole saws. If nec-

essary, replace prior to using in your hole-cutting

tool. Dull or damaged cutting edges can lead to

injury, tool breakage, or excessive heat buildup in

the workpiece and the tool.

Set-Up Instructions

Model HC-300

WARNING

When setting up the hole saw, it should be

unplugged and the switch should be in the OFF

position. To prevent serious injury, the tool must

be properly set up.

1. Determine the size and location of the hole to be

cut. Follow coupling manufacturer’s recommenda-

tions for hole size to coupling size.

2. Select hole saw and arbor to the hole size required.

See section 5 of the RIDGID catalog for saw order-

ing information.

3. Place the HC-300 on a clean bench or ground to

install hole saw and arbor into drill chuck.

NOTE! The

1

/

4

″ pilot drill is recommended for pipe that is

installed for it prevents the pipe slug from falling

into the system. If pilot is used, make sure it is

tight in arbor and exposed no more than

3

/

8

″.

4. Ensure the chain assembly and sliding bar handle

is in working order and free to move.

NOTE! It is possible to attach the HC-300 to the pipe as a

complete assembly or in two pieces.

HC-450/HC-300 Hole Cutting Tools

Ridge Tool Company • Elyria, Ohio • U.S.A.

10

5. For two-piece mounting, separate the base from

the motor assembly by lifting the motor while

pulling the plunger (Figure 13) located in rear of the

left post (front view). When lifting the motor assem-

bly, use the handle.

6. Make sure there is adequate clearance to mount

and position the HC-300.

WARNING

When cutting into an existing system, the pipe

must be drained and depressurized. Do not use

in the presence of flammable gas, vapor or dust.

7. Mount the base in the proximity of the place to be

cut. To do so, place the base on top of the work-

piece. The front edge of the base is 1

9

/

16

″ inches

from the chuck centerline. (Figure 14)

8. Turn crank handle fully counterclockwise to make

sure the hook is completely lowered and aligned

with the mark in casting.

9. Hook the chain into the base latch.To do so, pull

the chain slightly to compress the spring mecha-

nism. Once the chain is latched into hook, the

spring tension keeps the chain engaged. Use the

screw mechanism to fully tighten the chain.

(Figures 15 & 16)

NOTE! Completely lower hook until it reaches the cast-

ing marks. Failure to do so will result in inade-

quate travel to properly tension the chain.

NOTE! If the hole location is on the bottom or side of

the pipe, rotate the HC-300 to the desired loca-

tion before tightening the swivel handle.The unit

is designed to drill in any position.

HC-450/HC-300 Hole Cutting Tools

Figure 13 – Model HC-300 Plunger

Figure 14 – HC-300 Chuck Centerline

Figure 15 – Hooking the Chain

1

9

/

16

″

40mm

Ridge Tool Company • Elyria, Ohio • U.S.A.

11

NOTE! The HC-300 features a spring loaded hooking

mechanism that allows for easier tool pre-setting.

Always tighten the chain using the swivel handle

when the exact location of the cut is determined.

10. Machined flats are provided on the tool’s base and

posts to assist leveling by using a torpedo level.

(Figures 17 & 18) Once the tool is properly posi-

tioned, tighten crank handle securely.

NOTE! The flat area with the RIDGID lettering in the

back of the base and the machined areas on the

side of the posts are designed for level mount-

ing. They are useful when series of holes need

to be aligned.

WARNING

Never let go of the tool until the chain is fully

tightened. Doing so may result in the tool becom-

ing loose and falling, resulting in serious injury.

11. Lift the HC-300 motor assembly and mount on the

two posts by pushing firmly against the post

springs until you hear a click sound, indicating that

the plunger latch mechanism is properly engaged.

(Figure 19)

NOTE! The click sound indicates that the plunger has

captured the base and the motor assembly.

HC-450/HC-300 Hole Cutting Tools

Figure 16 – Tightening Chain

Figure 17 – Model HC-300 Level Mounting Area

Figure 18 – Model HC-300 Level Mounting Area

Figure 19 – Model HC-300 Putting the Motor and Base

Assembly Together

Ridge Tool Company • Elyria, Ohio • U.S.A.

12

WARNING

Do not attempt to start, detach or carry the tool

without the plunger engaged. The motor assem-

bly and the base could separate resulting in seri-

ous injury.

WARNING

Position electrical cord clear of the base of hole

saw to prevent cord damage and electrical shock.

12. Plug the hole cutting tool into the electrical outlet,

making sure to position the power cord along the

clear path. If the power cord does not reach the

outlet, use an extension cord in good condition.

(See page 2.)

WARNING

To avoid electric shock and electrical fires,

never use and extension cord that is damaged

or does not meet the following requirements:

• The cord has a three-prong plug similar to

shown in Electrical Safety.

• The cord is rated as “W” or “W-A” if being used

outdoor.

• The cord has a wire thickness gauge that does

not exceed 14 AWG if shorter than 30 feet or

12 AWG if 30 feet or longer. If the cord is too

long or if the wire thickness is too small, the

cord may overheat, melting the cord’s insula-

tion or causing nearby objects to ignite.

Operating Instructions

Model HC-300

WARNING

Do not use a hole cutting tool without proper

eye protection.

1. The Model HC-300 is turned on by depressing an

ON/OFF switch located on the side of the unit

behind the feed wheel. (Figure 20)

2. Feed the hole saw into the pipe by turning feed

wheel handle counterclockwise using moderate

force so as to not overload the motor.

WARNING

Keep fingers and hands away from the saw

blade. Do not reach across the hole saw or wear

loose gloves or clothing that may become entan-

gled and cause serious injury.

3. Rotate feed handle counter-clockwise to apply

downward pressure on the hole saw.

WARNING

Forcing hole saw into pipe will not reduce cut-

ting time. Therefore, do not overfeed saw while

cutting. Doing so will result in premature saw

failure or possible serious injury.

4. After completing the hole cut, retract the saw from

the pipe by turning the feed wheel clockwise.

NOTE! When branching off an existing pipe system, use

a hole saw with the

1

/

4

″ pilot drill. The pilot drill

helps retain the pipe slug in the hole saw.

5. Turn unit OFF by depressing ON/OFF switch to the

OFF position.

6. Remove unit by:

A. Unclamping entire assembly or

B. Retrieving motor assembly by pulling plunger

and then unclamping the base.

7. Brush away all metal chips created by the hole saw

from the area around the hole.

NOTE! The flat area with the RIDGID lettering in the

back of the base and the machined areas on the

side of the posts are designed for level mount-

ing. They are useful when series of holes need to

be aligned.

HC-450/HC-300 Hole Cutting Tools

Figure 20 – Model HC-300 ON/OFF Switch

Ridge Tool Company • Elyria, Ohio • U.S.A.

13

Maintenance

WARNING

Always unplug power cord before servicing the

hole saw.

Motor Brush Replacement

Check motor brushes every 6 months and replace when

worn to less than

1

/

2

″. If commutator is worn, the outer

dimension of the commutator should be turned and the

mica should be undercut before replacing the brushes.

This should only be done by qualified personnel.

Service and Repair

Service and repair work on this Hole Cutting Tool must

be performed only by qualified repair personnel. Hole

Cutting Tools should be taken to a RIDGID Authorized

Service Center or returned to the factory. When servic-

ing this tool, only identical replacement parts should be

used. Failure to follow these steps may create a risk of

electrical shock or other serious injury.

Contact the Ridge Tool Company at (800) 519-3456

or www.ridgid.com for the nearest Authorized Service

Center.

If you have any questions regarding the operation or

function of this tool, call or write to:

Ridge Tool Company

Technical Service Department

400 Clark Street

Elyria, Ohio 44036-2023

Telephone: 800-519-3456

When corresponding please give all information

shown on the nameplate of your tool including model

number, voltage and serial number.

HC-450/HC-300 Hole Cutting Tools

Ridge Tool Company • Elyria, Ohio • U.S.A.

14

HC-450/HC-300 Hole Cutting Tools

Page is loading ...

Ridge Tool Company • Elyria, Ohio • U.S.A.

30

Scies à cloche HC-450 – HC-300

Page is loading ...

Ridge Tool Company • Elyria, Ohio • U.S.A.

46

Máquinas Perforadoras HC-450/HC-300

LIFETIME WARRANTY

The reputation of RIDGID

®

tools is the result of consistent product

quality and years of pride in workmanship. Rigorous checks and con-

trols, from raw materials to packaged products, ensure product confi-

dence widely accepted as the benchmark of the professional trades.

RIDGID

®

tools are warranted to be free of defects in workmanship or

material for the life of the tool. Expendable Materials, such as pipe or

drain cleaning tools, rods and cables, etc. are not covered by this war-

ranty. Obviously, failures due to misuse, abuse, or normal wear and

tear are not covered by this warranty. NO OTHER WARRANTY

EXPRESS OR IMPLIED, APPLIES, INCLUDING MERCHANTABILITY OR

FITNESS FOR A PARTICULAR PURPOSE. No employee, agent, dealer,

or other person is authorized to alter this or make any other warranty

on behalf of RIDGE TOOL COMPANY. To obtain the benefit of this war-

ranty, deliver the complete product prepaid to RIDGE TOOL COMPANY

or any RIDGID

®

AUTHORIZED SERVICE CENTER. Pipe wrenches and

other hand tools should be returned to place of purchase. Warranted

products will be repaired or replaced, at RIDGE TOOL'S option, at no

charge and returned via prepaid transportation. This limited LIFETIME

WARRANTY is the sole and exclusive warranty for RIDGID

®

products,

and the remedy of repair or replacement is the sole and exclusive rem-

edy for any nonconformity with this warranty. RIDGE TOOL shall not

be responsible for damages of any sort, including incidental or conse-

quential damages.

GARANTIE A VIE

Le renommé des outils RIDGID

®

est le résultat d’une qualité constante

des produits et d’un grand amour du métier. Des less rigoureux, allant

des matières premières jusqu’aux produits emballés, assurent un

niveau de confiance tel qu’il sert souvent d’étalon dans less milieux

professionnels. Less outils RIDGID

®

sont garantis contre toutes défail-

lances de main d’oeuvre et de matériel. Evidemment, less défaillances

dues aux mauvaises applications, à l’abus ou à l’usure normale ne sont

pas couvertes par cette garantie. AUCUNES AUTRES GARANTIES

TACITES OU IMPLICITES, Y COMPRIS GARANTIES DE QUALITE

MARCHANDE OU D’APPLICATION PARTICULIERE, NE SONT APPLICA-

BLES. Aucun employé, agent, distributeur ou autre personne n’est

autorisé à modifier ou compléter cette garantie au nom de la RIDGE

TOOL COMPANY. Pour bénéficier de cette garantie, expédiez le produit

complet à la RIDGE TOOL COMPANY ou à un CENTRE DE REPARA-

TIONS RIDGID

®

agréé. Less clés à pipe et autres outils manuels doivent

être ramenés au point d’achat. Less produits sous garantie seront, à la

seule discrétion de RIDGE TOOL, soit gratuitement réparés ou rem-

placés, expédition en port payé compris. Cette GARANTIE A VIE condi-

tionnelle est la seule et unique garantie offerte pour les produits

RIDGID

®

, et sa responsabilité se limite à la réparation ou au remplace-

ment de tout outil non conforme selon la garantie. RIDGE TOOL se

dégage de toute responsabilité civile, qu’il s’agisse de dommages

directs ou indirects.

GARANTIA VITALICIA

El renombre de las herramientas RIDGID

®

es el resultado de la consis-

tente calidad de sus productos y de muchos años de excelencia en la

mano de obra. La rigurosa inspección y el sistemático control de cali-

dad, de las materias primas y hasta de los productos ya embalados,

garantizan la confianza en nuestros productos, los que se han

transformado en hitos contra los cuales se miden las demás herra-

mientas profesionales. Las herramientas RIDGID

®

están garantizadas

contra defectos de los materiales o de la mano de obra. Obviamente,

las fallas debidas al mal uso, abuso o desgaste normal, no están

cubiertas por esta garantía. NO ES PERTINENTE NINGUNA OTRA

GARANTIA, EXPRESA O IMPLICITA, INCLUSO LA NEGOCIABILIDAD O

IDONEIDAD PARA UN PROPOSITO PARTICULAR. Ningún empleado,

agente, distribuidor u otra persona está autorizado para modificar la

presente ni para ofrecer cualquier otra garantía en nombre de RIDGE

TOOL COMPANY. Para obtener los beneficios de esta garantía, envíe el

producto completo con porte pagado a RIDGE TOOL COMPANY o

cualquier SERVICENTRO INDEPENDIENTE autorizado por RIDGID.

Las llaves para tubos y otras herramientas manuales deben ser

devueltas al lugar de su adquisición. Los productos garantizados

serán reparados o substituidos, a discreción de RIDGE TOOL, gratuita-

mente, y serán devueltos mediante el transporte pre-pagado. Esta

GARANTIA VITALICIA limitada es la única y exclusiva garantía para los

productos RIDGID

®

, y la reparación o substitución es el único y exclu-

sivo recurso ofrecido en el título de esta garantía. RIDGE TOOL no se

hará responsable por daños de ningún tipo, incluso los de naturaleza

incidental o consecuente.

Ridge Tool Subsidiary

Emerson Electric Co.

Ridge Tool Company

400 Clark Street

Elyria, Ohio 44036-2023

Printed in U.S.A. 9/99 999-998-050.10

RIDGID HC-300 User manual

This manual is also suitable for

RIDGID HC-300 User manual

in other languages

Related papers

Other documents