Philips HQ9190 User manual

Page is loading ...

4

Important

Read these instructions for use carefully before using

the appliance and save them for future reference.

Only use the powerplug supplied.

The powerplug transforms 100-240 volts to a safe

low voltage of less than 24 volts.

The powerplug contains a transformer. Do not cut

off the powerplug to replace it with another plug,

as this will cause a hazardous situation.

Do not use a damaged powerplug.

If the powerplug is damaged, always have it

replaced by one of the original type in order to

avoid a hazard.

Make sure the powerplug does not get wet.

Charge and store the appliance at a temperature

between 5 cC and 35 cC.

Never immerse the charging stand in water nor

rinse it under the tap.

Do not recharge the shaver in a closed pouch.

Always unplug the shaver before cleaning it under

the tap.

The appliance complies with the internationally

approved IEC safety regulations and can be safely

cleaned under the tap.

Be careful with hot water. Always check if the water

is not too hot, to prevent your hands from getting

burnt.

Electromagnetic elds (EMF)

This Philips appliance complies with all standards

regarding electromagnetic elds (EMF). If handled

properly and in accordance with the instructions in

this instruction manual, the appliance is safe to use

according to scientic evidence available today.

-

ENGLISH

The display

This appliance offers you the unique possibility to

choose the display layout you prefer: a number

layout or a battery symbol layout.

1 Press the on/off button approx. 3 seconds to

enter the menu.

The menu has three different modes: the travel lock

mode and two display layout modes.

You will enter the menu in the travel lock mode,

indicated by a rotating key symbol.

You can scroll through the three modes (travel

lock, battery symbol layout and number layout) by

pressing the on/off button briey in quick succession.

2 To select one of the two display layouts, stop

pressing the on/off button when the layout you

prefer appears on the display.

3 Wait a few seconds without pressing the on/off

button until you hear a beep.

This beep indicates that the display has been set to

the selected layout.

Note:The rst mode you enter after pressing the on/off

button for 3 seconds is the travel lock mode (indicated

by a rotating key symbol). If you do not press the on/off

button again within a few seconds, the travel lock is

activated and the display will not switch to the rst

display layout mode. To deactivate the travel lock, press

the on/off button for 3 seconds again (see chapter

‘Storage’).

You can change the display layout at any time.

Note:When you start using the appliance for the rst

time or after a long period of disuse, it could take

several minutes before anything appears on the display.

,

ENGLISH 5

The display provides the following

information:

Charging

Number layout:

When the shaver is being charged, the display shows

the minutes indication and the plug symbol with a

blinking power symbol.

Battery symbol layout:

When the shaver is being charged, the display shows

the battery symbol and the plug symbol with a

blinking power symbol.

Battery fully charged

As soon as the battery has been fully charged,

the word FULL runs across the display.

After a few hours the word FULL stops

appearing. The display shows the minutes

indication and the plug symbol.

Battery running low

Number layout:

When the battery is running low, the display shows a

blinking minutes indication and blinking plug symbol

when you switch the shaver off. HQ9190 only: you

will also hear a few short beeps.

Battery symbol layout:

When the battery is running low, the display shows

a blinking battery symbol and blinking plug symbol

when you switch the shaver off. HQ9190 only: you

will also hear a few short beeps.

,

ENGLISH6

Battery empty

To indicate that the battery voltage is too low to

operate the appliance, LO appears on the display.

Recharge the battery. See chapter ‘Charging’.

Cleaning shaver

When the shaver is due to be cleaned, the tap

symbol with blinking water drops appears on the

display.

Replacing shaving heads

When the shaving heads need to be replaced

(every two years), the shaving unit symbol starts

blinking when you switch the shaver off. HQ9190

only: at the same time you will hear a beep.

If you do not replace the shaving heads right away,

the shaving unit symbol remains visible during the

next 7 shaves.

You can reset the appliance by pressing the

on/off button for 3 seconds while the shaving unit

symbol is blinking. The shaving unit symbol then

disappears. HQ9190 only: you will hear a short

conrming beep.

If you have not reset the system after these 7

shaves, the system will automatically reset itself.

Demonstration program

The appliance has a unique demonstration program.

Press the on/off button for 6 seconds.

After 3 seconds the lock symbol appears; keep the

on/off button pressed.

The demonstration will start automatically.

During the demonstration the appliance will be

,

-

,

ENGLISH 7

automatically switched on 2 times. You can interrupt

the demonstration by pressing the on/off button.

Charging

Make sure the appliance is switched off before you

start charging it.

Charging normally takes approx. 1 hour.

You can also shave without charging by connecting

the shaver to the mains.

A fully charged shaver has a cordless shaving time of

up to 30 days.

Charging the appliance

1 Put the appliance plug in the shaver.

2 Put the powerplug in the wall socket.

3 Remove the powerplug from the wall socket

and pull the appliance plug out of the shaver

when the battery has been fully charged.

Charging stand

You can also charge the appliance by placing it in

the charging stand.

1 Place the shaver properly in the plugged-in

charging stand.

2 Lift the shaver from the stand without tilting it.

,

ENGLISH8

Removing and inserting the clock

1 Turn the clock anticlockwise (1) (‘click’) and

pull it out (2).

2 Insert the clock (1) and turn it clockwise (2)

(‘click’).

Setting the time

1 Set the time by pressing the small button at the

back of the clock.

The time can only be set forward.

Replacing the battery

1 Remove the cap. Then remove the battery by

means of a miniature screwdriver.

2 Insert a new battery and put the cap back into

place.

ENGLISH 9

Using the appliance

Personal Comfort Control

The Personal Comfort Control system allows

you to adapt the shaver to your skin type.

You can set the shaver to ‘Normal’ for a fast and

comfortable close shave.

You can set the shaver to ‘Sensitive’ for a

comfortable close shave with optimal skin

comfort.

The ‘S’ position is best suited for sensitive skin.

The ‘N’ position is best suited for normal skin.

The in-between positions are suitable for skin

types between normal and sensitive.

HQ9190 only: the display shows the position

selected.

Shaving

1 Switch the shaver on by pressing the on/off

button once.

,

-

,

ENGLISH10

When you switch the shaver on or off, all lights

and symbols go on and then the remaining battery

capacity is shown for a few seconds.

2 Move the shaving heads quickly over your skin,

making both straight and circular movements.

Shaving on a dry face gives the best results.

Your skin may need 2 or 3 weeks to get

accustomed to the Philips shaving system.

3 Switch the shaver off by pressing the on/off

button once.

4 Put the protection cap on the shaver every

time you have used it, to prevent damage.

Trimming

For grooming sideburns and moustache.

1 Open the trimmer by pushing the slide

downwards.

The trimmer can be activated while the motor is

running.

2 Closethetrimmerwithyourindexnger.

Cleaning and maintenance

Clean the shaver when the tap symbol with blinking

water drops appears on the display.

Regular cleaning guarantees better shaving

performance.

-

ENGLISH 11

The normal way to clean the appliance is to rinse

the shaving unit and the hair chamber with hot

water every time you have used the shaver.

Be careful with hot water. Always check if the

water is not too hot, to prevent your hands from

getting burnt.

Every day: shaving unit and hair chamber

1 Switch the shaver off, remove the powerplug

from the wall socket and pull the appliance plug

out of the shaver.

2 Press the release button to open the shaving

unit.

3 Clean the shaving unit and the hair chamber by

rinsing them under a hot tap for some time.

Make sure the inside of the shaving unit and the hair

chamber have been cleaned properly.

4 Rinse the outside of the appliance.

5 Close the shaving unit and shake off excess

water.

Never dry the shaving unit with a towel or tissue,

as this may damage the shaving heads.

6 Open the shaving unit again and leave it open

to let the appliance dry completely.

You can also clean the hair chamber without water

by using the brush supplied.

ENGLISH12

Every six months: shaving heads

1 Open the shaving unit, turn the lock

anticlockwise (1) and remove the retaining

frame (2).

2 Clean the cutters and guards with the brush

supplied.

Do not clean more than one cutter and guard

at a time, since they are all matching sets. If you

accidentally mix up the cutters and guards, it

may take several weeks before optimal shaving

performance is restored.

3 Put the shaving heads back into the shaving

unit. Put the retaining frame back into the

shaving unit and turn it clockwise.

4 Close the shaving unit.

Trimmer

Clean the trimmer every time you have used it.

1 Switch the shaver off, remove the powerplug

from the wall socket and pull the appliance plug

out of the shaver.

2 Clean the trimmer with the brush supplied.

3 Lubricate the trimmer teeth with a drop of

sewing machine oil every six months.

ENGLISH 13

Charging stand

Never immerse the charging stand in water nor

rinse it under the tap.

You can clean the charging stand with a moist cloth.

Storage

Put the protection cap on the shaver to prevent

damage.

Store the appliance in the luxury cassette/pouch

or place the appliance in the charging stand.

Travel lock

If you are going to travel, it is possible to lock the

shaver. The travel lock prevents the shaver from

being switched on by accident.

Activating the travel lock

1 Press the on/off button for 3 seconds to enter

the travel lock mode (indicated by a rotating

key symbol).

2 Wait a few seconds without pressing the on/off

button to activate the travel lock.

,

ENGLISH14

3 The motor switches off and the key symbol is

visible on the display to indicate that the travel

lock has been activated.

Note:If you press the on/off button again within a few

seconds after entering the travel lock mode, the travel

lock will not be activated. Instead, you will have entered

one of the two display layout modes. If you want to

return to the travel lock mode, press the on/off button

two more times until you are back in the travel lock

mode (indicated by rotating the key symbol). Then wait

a few seconds without pressing the on/off button to

activate the travel lock.

You can always return to the menu by pressing

the on/off button for 3 seconds.

Deactivating the travel lock

Press the on/off button for 3 seconds.

The motor starts running to indicate that the shaver

has been unlocked. The shaver is now ready for use

again.

Replacement

Replace the shaving heads when the shaving unit

symbol appears on the display.

Replace damaged or worn shaving heads with HQ9

Philips shaving heads only.

1 Switch the shaver off, remove the powerplug

from the wall socket and pull the appliance plug

out of the shaver.

,

ENGLISH 15

2 Press the release button to open the shaving

unit.

3 Turn the lock anticlockwise (1) and remove the

retaining frame (2).

4 Remove the shaving heads and place new ones

in the shaving unit.

Make sure that the projections of the shaving heads

t exactly into the recesses.

5 Put the retaining frame back into the shaving

unit (1) and turn the lock clockwise (2).

6 Close the shaving unit.

The shaving unit symbol will go out if you keep

the on/off button pressed for 3 seconds.

Accessories

The following accessories are available:

HQ8500/HQ8000 powerplug.

HQ9 Philips Shaving Heads.

HQ110 Philips Shaving Head Cleaning Spray (not

available in China).

HQ8010 car cord.

,

-

ENGLISH16

Environment

Do not throw the appliance away with the

normal household waste at the end of its life,

buthanditinatanofcialcollectionpointfor

recycling. By doing this you will help to preserve

the environment.

The built-in rechargeable battery contains

substances that may pollute the environment.

Always remove the battery before discarding the

applianceorhandingitinatanofcialcollection

point.Disposeofthebatteryatanofcial

collection point for batteries. If you have trouble

removing the battery, you can also take the

appliance to a Philips service centre, which will

remove the battery for you and will dispose of it

in an environmentally safe way.

Disposal of the shaver battery

Only remove the battery if it is completely empty.

1 Remove the powerplug from the wall socket

and pull the appliance plug out of the shaver.

2 Let the shaver run until it stops, undo the

screws and open the shaver.

3 Remove the battery.

Do not connect the shaver to the mains again after

the battery has been removed.

,

ENGLISH 17

Guarantee & service

If you need information or if you have a

problem, please visit the Philips website at

www.philips.com or contact the Philips Customer

Care Centre in your country (you will nd its phone

number in the worldwide guarantee leaet). If there

is no Customer Care Centre in your country, turn

to your local Philips dealer or contact the Service

Department of Philips Domestic Appliances and

Personal Care BV.

Troubleshooting

1

Reduced shaving performance

Cause 1: the shaving heads are dirty. The shaver

has not been rinsed long enough or the water

used was not hot enough.

Clean the shaver thoroughly before you continue

shaving. See chapter ‘Cleaning and maintenance’.

Cause 2: long hairs are obstructing the shaving

heads.

Clean the cutters and guards with the brush

supplied. See chapter ‘Cleaning and maintenance’,

section ‘Every six months: shaving heads’.

Cause 3: the shaving heads are damaged or worn.

Replace the shaving heads. See chapter

‘Replacement’.

2 The shaver does not work when the on/off

button is pressed.

Cause 1: the shaving heads are dirty.

Recharge the battery. See chapter ‘Charging’.

Cause 2: the appliance is not connected to the

mains.

Put the powerplug in the wall socket.

-

ENGLISH18

3 The shaving unit has come off the shaver.

Cause: the shaving unit has not been placed

correctly.

If the shaving unit becomes detached from the

shaver, you can easily reattach it (‘click’).

4 The display shows the word CHECK and

a blinking shaving unit symbol and tap unit

symbol.

Cause 1: long hairs and dirt are obstructing the

shaving heads.

Clean the shaver thoroughly before you continue

shaving. See chapter ‘Cleaning and maintenance’.

Cause 2: the shaving heads are damaged or worn.

Replace the shaving heads. See chapter

‘Replacement’.

-

ENGLISH 19

Page is loading ...

Philips HQ9190 User manual

Philips HQ9190 User manual

Related papers

Other documents