English .......................................................................................... 2
USA: 1-800-851-8900
Visit www.hamiltonbeach.com for our complete line of products and Use and Care
Guides – as well as delicious recipes, tips, and to register your product online!
Français ...................................................................................... 14
Canada : 1-800-267-2826
Rendez-vous sur www.hamiltonbeach.ca pour notre liste complète de produits et
de nos manuels utilisateur – ainsi que nos délicieuses recettes, nos conseils, et pour
enregistrer votre produit en ligne !
Español ...................................................................................... 29
En México: 01-800-71-16-100
¡Visite www.hamiltonbeach.com.mx para obtener nuestra línea completa de productos
y las Guías de Uso y Cuidado, además de deliciosas recetas, consejos, y para registrar
su producto en línea!
Irons
Fer à repasser
Planchas
840164202
Le invitamos a leer cuidadosamente este
instructivo antes de usar su aparato.
READ BEFORE USE
À LIRE AVANT UTILISATION
LEA ANTES DE USAR
840164202 ENv05.qxd:840164200 ENv01.qxd 7/14/10 1:24 PM Page 1
3
2
This product is intended for household use only.
WARNING! Shock Hazard: This appliance has a polarized plug (one
wide blade) that reduces the risk of electric shock. The plug fits only
one way into a polarized outlet. Do not defeat the safety purpose of
the plug by modifying the plug in any way or by using an adapter. If the
plug does not fit, reverse the plug. If it still does not fit, have an electri-
cian replace the outlet.
OTHER CONSUMER SAFETY INFORMATION
Please Read Before First Use
• During first use of the iron, it may appear to smoke. This will
stop and does not indicate a defect or hazard.
• Many irons spit or sputter during the first few uses with tap
water. This happens as the steam chamber becomes condi-
tioned. This will stop after a few uses.
• Steam vents should be cleared before first use. Prepare iron for
steam ironing; then iron over an old cloth for a few minutes
while letting iron steam.
IMPORTANT SAFEGUARDS
When using your flatiron, basic safety precautions should always be
followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING
1. Use iron only for its intended use.
2. Verify that the voltage in your home corresponds to that of your
appliance.
3. To protect against risk of electric shock, do not immerse the iron
in water or other liquids.
4. The iron should always be turned to OFF before plugging or
unplugging from outlet. Never yank cord to disconnect from
outlet; instead, grasp plug and pull to disconnect.
5. Do not allow cord to touch hot surfaces. Let iron cool completely
before putting away. Loop cord loosely around iron when storing.
6. Always disconnect iron from electrical outlet when filling with
water or emptying and when not in use.
7. Do not operate iron with a damaged cord or if the iron has been
dropped or damaged. To avoid the risk of electric shock, do not
disassemble the iron. Call our toll-free customer service number
for information on examination and repair. Incorrect reassembly
can cause a risk of electric shock when the iron is used.
8. Close supervision is necessary for any appliance being used by
or near children. Do not leave iron unattended while connected
or on an ironing board.
9. Burns can occur from touching hot metal parts, hot water, or
steam. Use caution when you turn a steam iron upside down –
there may be hot water in the reservoir.
SPECIAL INSTRUCTIONS
1. To avoid a circuit overload, do not operate another high-wattage
appliance on the same circuit.
2. If an extension cord is absolutely necessary, a 10-ampere cord
should be used. Cords rated for less amperage may overheat.
Care should be taken to arrange the cord so that it cannot be
pulled or tripped over.
SAVE THESE INSTRUCTIONS!
840164202 ENv05.qxd:840164200 ENv01.qxd 7/14/10 1:24 PM Page 2
5
4
Parts and Features
The iron is equipped with a position sensor. If iron is left motionless,
it will turn off automatically and cool to room temperature.
To restart, move iron and allow it to reheat on heel position:
— Iron will reheat to the previously selected setting.
— Iron will lose memory when turned off ( O ) or unplugged.
The iron turns off automatically when left in these positions:
Iron Position
Inadvertently resting
on soleplate
Inadvertently resting
on either side
Resting on heel
Position Sensing Feature
Retractable
Cord*
Cord Release
Button*
Spray and
Blast of Steam
Buttons
Adjustable
Steam Dial
Water Tank
Fill Cover
Soleplate
Water Tank
Self-Clean
Button
Power Indicator
Lights (see inset)
Temperature
Settings
Button
(see inset)
Heel Rest
The light is . . . This means . . .
RED and Solid Power OFF ( O ). This light will
remain on until iron is unplugged.
RED and Blinking Iron was heating/reheating and went
to OFF ( O ). Iron will reheat when
moved.
GREEN and Solid Iron is heated and ready for ironing.
GREEN and Blinking Iron is preheating/heating.
*on selected models only
Motionless Time
30 seconds
15 minutes max
15 minutes
840164202 ENv05.qxd:840164200 ENv01.qxd 7/14/10 1:24 PM Page 4
6
7
To Dry Iron
1. Plug in iron.
2. Turn Adjustable Steam Dial to the (Dry Iron) position.
3. Set Temperature Settings to desired temperature. With iron
in an upright position, allow 3 minutes for iron to reach
desired temperature. Do not preheat iron with soleplate
facing down.
4. To turn iron off, set Temperature Settings to OFF ( O ).
The iron may be turned off by pressing the Temperature
Settings Button for 3 seconds.
To Steam Iron
1. Unplug iron. Open Water Tank Fill Cover. Using a cup,
slowly pour 6 ounces (3⁄4 cup) of tap water into the water
tank opening. Close Water Tank Fill Cover.
2. Plug in iron.
3. Set Temperature Settings to desired setting in steam
range. With iron in an upright position, allow 3 minutes for
iron to reach desired temperature. Do not preheat iron with
soleplate facing down.
4. Set Adjustable Steam to desired steam output.
5. To turn off, turn Adjustable Steam Dial to (Dry Iron). Set
Temperature Settings to OFF ( O ). (Iron may also be turned
off by pressing Temperature Settings Button for 3 seconds.)
6. Empty water from the iron following directions in “Care and
Cleaning.”
Water
Please use ordinary tap water. If you have extremely hard
water, alternate between tap water and distilled water for
use in the iron.
Adjustable Steam Dial
Provides minimum steam for wool or
maximum steam for linen. Set the dial
to to change to Dry Iron.
Blast of Steam and Spray Buttons
Push Blast of Steam Button for an extra
blast of steam. Push Spray Button to
release a fine spray of water for difficult
wrinkles in cotton or linen.
Blast of
Steam
Spray
Features (on selected models)
Retractable Cord
1. Pull cord to desired length. Do not
unwind cord beyond colored tape
indicator on cord.
2. To store cord, press and hold the
Cord Release Button while guiding
the cord into the storage area.
WARNING! To reduce the risk of
an eye injury, hold the plug while
retracting the cord.
840164202 ENv05.qxd:840164200 ENv01.qxd 7/14/10 1:24 PM Page 6
9
8
Temperature Settings
To Iron
Off
Nylon
Acrylic
Silk
Polyester
Rayon
Wool
Cotton
Linen
Ironing Instructions
Steam
Setting
Dry iron on the reverse side of the fabric.
Dry iron on the reverse side of the fabric.
Dry iron on the reverse side of the fabric.
Iron with fabric still damp.
Iron on the reverse side of fabric.
Steam iron on the reverse side of fabric.
Iron while still damp using steam
and/or spray.
Iron on reverse side of fabric while still
damp.
Vertical Steam
1. Follow Steps 1 through 4 in
“To Steam Iron.”
2. Hang garment in a location that is
not susceptible to damage from heat
or moisture. Do not hang in front of
wallpaper, window, or mirror.
3. Hold iron about 6 inches away from
garment. Press and release the Blast of Steam Button to
steam out wrinkles. Do not press Blast of Steam Button
more than once every
3 seconds.
4. To turn iron off, turn Temperature Settings to OFF ( O ).
Unplug iron.
5. Empty water from the iron following directions in “Care and
Cleaning.”
NOTICE: Do not allow the hot soleplate to touch delicate
garments.
Features (cont.)
Care and Cleaning
Iron
1. The Water Tank of your iron should be emptied after each
use. Set Temperature Settings Button to OFF ( O ). Unplug
the iron and open Water Tank Fill Cover. Turn iron upside
down until Water Tank Opening is parallel with sink. Water
will run out of water tank opening.
2. After iron has completely cooled, store in an upright posi-
tion. NOTICE: Do not store iron laying flat on soleplate.
840164202 ENv05.qxd:840164200 ENv01.qxd 7/14/10 1:24 PM Page 8
11
Troubleshooting
Won’t
heat
PROBLEM
PROBABLE CAUSE
Water is
leaking
Won’t
steam
Leaves
spots
• Is the iron plugged in and the outlet working?
Check the outlet by plugging in a lamp.
• Is the Temperature Settings Button set on a
fabric setting?
• Iron may have gone to auto off (blinking red
light). Push “Settings” to restart and adjust to
desired temperature.
• Do not overfill the water tank.
• If steam ironing, is Adjustable Steam Dial in a
steam position, the Temperature Settings
Button in the steam range, and did the iron
have enough time to preheat?
• If dry ironing, make sure the Adjustable Steam
Dial is in the (DRY IRON) position.
• Check the water level.
• Is the Adjustable Steam Dial in a STEAM
position?
• Has the iron had enough time to preheat?
• ALWAYS empty the water tank of the iron
after using. Water left in the tank may discolor
clothing and soleplate.
• If the iron cord should become twisted, unplug
iron and let cool. Hold iron cord in the middle
of entire length. Let plug and iron dangle freely
until cord uncoils. This will extend the life of
your iron cord.
Twisted
cord
10
Care and Cleaning (cont.)
Soleplate
1. Never iron over zippers, pins, metal rivets, or snaps, since
these may scratch the soleplate.
2. To clean occasional buildup on the soleplate, wipe with
a sudsy cloth. Do not use abrasive cleansers or metal
scouring pads.
3. Always store iron upright in the heel rest position.
Self-Clean
To keep the steam vents clear of any buildup, follow these
instructions each time you iron using steam.
1. Set Temperature Settings Button to OFF ( O ) and set
Adjustable Steam Dial to (DRY). Fill iron with water
to 1⁄2 of its maximum capacity.
2. Set Temperature Settings Button to Linen setting and let
iron heat for 2 minutes. Keep Adjustable Steam Dial on
(DRY).
3. Set Temperature Settings Button to OFF ( O ). Unplug iron
and hold over a sink with soleplate facing down.
4. Turn Adjustable Steam Dial to (MAX), while pressing Self-
Clean Button often. Boiling water and steam will flow out of
steam vents. Allow all water to drain from iron.
5. Gently move iron front to back to allow water to clean
entire soleplate area.
6. If water still remains inside of soleplate, reheat iron as
indicated in Step 2. Boiling water and steam could still flow
out of steam vents.
840164202 ENv05.qxd:840164200 ENv01.qxd 7/14/10 1:24 PM Page 10
13
12
LIMITED WARRANTY
This warranty applies to products purchased in the U.S. and Canada. This is
the only express warranty for this product and is in lieu of any other warranty
or condition.
This product is warranted to be free from defects in material and
workmanship for a period of one (1) year from the date of original purchase.
During this period, your exclusive remedy is repair or replacement of this
product or any component found to be defective, at our option; however,
you are responsible for all costs associated with returning the product to us
and our returning a product or component under this warranty to you. If the
product or component is no longer available, we will replace with a similar
one of equal or greater value.
This warranty does not cover glass, filters, wear from normal use, use not
in conformity with the printed directions, or damage to the product resulting
from accident, alteration, abuse, or misuse. This warranty extends only to
the original consumer purchaser or gift recipient. Keep the original sales
receipt, as proof of purchase is required to make a warranty claim. This
warranty is void if the product is used for other than single-family household
use.
We exclude all claims for special, incidental, and consequential damages
caused by breach of express or implied warranty. All liability is limited to the
amount of the purchase price. Every implied warranty, including any
statutory warranty or condition of merchantability or fitness for a
particular purpose, is disclaimed except to the extent prohibited by law,
in which case such warranty or condition is limited to the duration of
this written warranty. This warranty gives you specific legal rights. You may
have other legal rights that vary depending on where you live. Some states
or provinces do not allow limitations on implied warranties or special,
incidental, or consequential damages, so the foregoing limitations may not
apply to you.
To make a warranty claim, do not return this appliance to the store. Please
call 1.800.851.8900 in the U.S. or 1.800.267.2826 in Canada or visit
hamiltonbeach.com in the U.S. or hamiltonbeach.ca in Canada. For faster
service, locate the model, type, and series numbers on your appliance.
Troubleshooting (cont.)
Blinking
red light
PROBLEM
PROBABLE CAUSE
All lights
blinking
Continuous
blinking
green light
• Iron went to auto off. Iron will reheat when
moved.
• Unplug iron; then plug back in to reset.
Reselect previous temperature setting. If all
lights are still blinking, call Customer Service.
• Overuse of steam causes the soleplate to cool.
The light blinks as the iron reheats.
840164202 ENv05.qxd:840164200 ENv01.qxd 7/14/10 1:24 PM Page 12
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
