Panasonic WH-ADC0309G3E5 Owner's manual

Português Nederlands Italiano Deutsch Español Français English

F569727

Model No.

Indoor Unit

WH-ADC0309G3E5

Outdoor Unit

WH-UD03EE5

WH-UD05EE5

WH-UD07FE5

WH-UD09FE5

Operating Instructions

Air-to-Water Hydromodule + Tank

Operating Instructions

Air-to-Water Hydromodule + Tank

2-15

Installation Instructions attached.

Serial number and production year please

refer to name plate.

Mode d’emploi

Ballon + Module Hydraulique Air/Eau

16-29

Consignes d’installation jointes.

Numéro de série et année de production

veuillez vous référer à la plaque signalétique.

Instrucciones de funcionamiento

Hydrokit Aire-Agua + Tanque

30-43

Instrucciones de instalación adjuntas.

Para saber el número de serie y el año de

producción consulte la placa indicadora.

Bedienungsanleitung

Luft/Wasser-Hydromodul +

Warmwasserspeicher

44-57

Installationsanleitung liegt bei.

Auf dem Typenschild finden Sie

Seriennummer und Baujahr.

Istruzioni operative

Idromodulo aria-acqua + serbatoio

58-71

Istruzioni per l’installazione allegate.

Per il numero di serie e l’anno di produzione,

fare riferimento alla targhetta di identificazione.

Gebruiksaanwijzing

Lucht-naar-water Hydromodule + Tank

72-85

De instructies voor installatie zijn bijgevoegd.

Voor het serienummer en jaar van fabricage

zie de naamplaat.

Instruções de funcionamento

Hidromódulo Ar-Água + Reservatório

86-99

Instruções de instalação anexadas.

Número de série e ano de produção por favor

consulte a placa de identificação.

Manufactured by:

Panasonic Appliances Air-Conditioning Malaysia Sdn. Bhd.

Lot 2, Persiaran Tengku Ampuan, Section 21,

Shah Alam Industrial Site, 40300 Shah Alam,

Selangor Darul Ehsan, Malaysia.

F569727_SS0814-1.indb 1F569727_SS0814-1.indb 1 21/08/2014 10:53:54 AM21/08/2014 10:53:54 AM

Process BlackProcess Black

2

Thank you for purchasing Panasonic product.

Before operating the system, read these operating

instructions thoroughly and keep them for future reference.

Table of contents

Safety precautions ………………………………………… 3-5

To adjust initial settings …………………………………… 6-7

How to use ……………………………………………… 8-11

Cleaning instructions ……………………………………… 12

Troubleshooting …………………………………………13-14

Information ………………………………………………… 15

The illustrations in this manual are for explanation purposes

only and may differ from the actual unit.

They are subject to change without notice for future

improvement.

Before use, make sure the system

has been installed correctly by an

authorised dealer according to the

given instructions.

• Panasonic Air-to-Water is a split system, consisting

of two units: indoor and outdoor units. The indoor unit

consist of the hydromodule and 200L sanitary water

tank.

• These operating instructions describe how to operate

the system using the indoor and outdoor units.

• As for the operation of other products such as radiator,

external thermo controller, and underfloor units, refer to

the operating instructions of each product.

• System could be locked to operate in HEAT mode and

disable COOL mode.

• Some functions described in this manual may not be

applicable to your system.

• Consult your nearest authorised dealer for further

information.

*

1

The system is locked to operate without COOL mode.

It can be unlocked only by authorised installers or our

authorised service partners.

*

2

Only displayed when COOL mode is unlocked

(Means when COOL mode is available).

Operating conditions

HEATING

(TANK)

HEATING

(CIRCUIT)

COOLING

(CIRCUIT)

Water outlet temperature (°C)

(Min. / Max.)

- / 65* 25 / 55 5 / 20

Outdoor ambient temperature (°C)

(Min. / Max.)

-20 / 35 16 / 43

* Above 55 °C, only possible with backup heater operation.

When the outdoor temperature is out

of the range in the table, the heating

capacity will drop significantly and the

outdoor unit may stop operating for its

protection.

The unit will restart automatically after

the outdoor temperature returns to the

specified range.

Fan Coil Unit

System overview

Open and Close Top Front Plate

Do not open or close the Top Front Plate by excessive

force.

To Open: To Close:

open

Top Front Plate

Bottom Front Plate

“click”

Hold in position

Control panel

“click”

close

Note:

Not recommended to open

the Bottom Front Plate.

(For authorised dealer/

specialist use only)

Indoor Unit

Power Supply Radiator

Shower

Floor HeatingOutdoor Unit

F569727_SS0814-1.indb 2F569727_SS0814-1.indb 2 21/08/2014 10:54:08 AM21/08/2014 10:54:08 AM

Process BlackProcess Black

3

English

To prevent personal injury, injury to

others or property damage, please

comply with the following:

Incorrect operation due to failure to

follow instructions below may cause

harm or damage, the seriousness of

which is classified as below:

WARNING

This sign warns of

death or serious

injury.

CAUTION

This sign warns of

injury or damage

to property.

The instructions to be followed are

classified by the following symbols:

This symbol denotes

an action that is

PROHIBITED.

These symbols denote

actions COMPULSORY.

WARNING

Indoor unit and outdoor unit

This appliance may be used by

children aged from 8 years and

above and persons with reduced

physical, sensory or mental

capabilities or lack of experience

and knowledge if they have been

given supervision or instruction

concerning use of the appliance

in a safe way and understand

the hazards involved. Children

shall not play with the appliance.

Cleaning and user maintenance

shall not be made by children

without supervision.

Please consult an authorised

dealer or specialist to clean the

internal parts, repair, install,

remove and reinstall the unit.

Improper installation and

handling will cause leakage,

electric shock or fire.

Confirm with an authorised

dealer or specialist on usage of

any specified refrigerant type.

Using refrigerant type other than

the specified may cause product

damage, burst and injury etc.

When open the Top Front Plate,

make sure it is securely hold

in position. Else it may fall and

cause injury.

Safety precautions

F569727_SS0814-1.indb 3F569727_SS0814-1.indb 3 21/08/2014 10:54:09 AM21/08/2014 10:54:09 AM

Process BlackProcess Black

4

Do not install the unit in

a potentially explosive or

flammable atmosphere. Failure

to do so could result in fire.

Do not insert your fingers

or other objects into the

indoor or outdoor unit; the

rotating parts may cause

injury.

Do not touch the outdoor unit

during lightning, it may cause an

electric shock.

Do not sit or step on the

unit, you may fall down

accidentally.

Do not install the indoor unit

outdoors. This is designed for

indoor installation only.

Power supply

Do not use a

modified cord, joint

cord, extension

cord or unspecified

cord to prevent

overheating and fire.

To prevent overheating, fire or

electric shock:

• Do not share the same power

outlet with other equipment.

• Do not operate with wet hands.

• Do not bend or twist power

supply cord.

If the supply cord is damaged,

it must be replaced by the

manufacturer, service agent or

similarly qualified persons in

order to avoid a hazard.

This unit is equipped with

Residual Current Circuit

Breaker/Earth Leakage Circuit

Breaker (RCCB/ELCB). Ask

an authorised dealer to check

RCCB/ELCB operation regularly,

especially after installation,

inspection, and maintenance.

RCCB/ELCB malfunction may

result in electric shock and/or

fire.

It is strongly recommended that

Install Residual Current Device

(RCD) on-site to prevent electric

shock and/or fire.

Before obtaining access to

terminals, all supply circuits must

be disconnected.

Stop using the product if any

abnormality/failure occurs and

disconnect the power supply.

(Risk of smoke/fire/electric

shock)

Examples of abnormality/failure

• RCCB/ELCB trips frequently.

• Burning smell is observed.

• Abnormal noise or vibration of

the unit is observed.

• Hot water leaks from the indoor

unit.

Contact your local dealer

immediately for maintenance/

repair.

Wear gloves during inspection

and maintenance.

Safety precautions

F569727_SS0814-1.indb 4F569727_SS0814-1.indb 4 21/08/2014 10:54:09 AM21/08/2014 10:54:09 AM

Process BlackProcess Black

5

English

This equipment must be earthed

to prevent electrical shock or fire.

Prevent electric shock by

disconnecting the power supply

- Before cleaning or servicing.

- When extended non-use.

This appliance is for multiple

uses. To avoid electric shock,

burn and/or fatal injury, make

sure to disconnect all power

supplies before accessing any

terminal in the indoor unit.

CAUTION

Indoor unit and outdoor unit

Do not wash the indoor unit

with water, benzine, thinner

or scouring powder to avoid

damage or corrosion on the unit.

Do not install the unit close

to any combustibles or at

bathroom. Otherwise, it may

cause electric shock and/or fire.

Do not touch the water discharge

pipe of the indoor unit during

operation.

Do not place any material on the

unit or under it.

Do not touch the sharp

aluminium fin; sharp parts

may cause injury.

Do not use the system during

sterilisation in order to prevent

scalding with hot water, or

overheating of shower.

Prevent water leakage by

ensuring that the drainage pipe

is connected properly.

After a long period of use, make

sure the installation rack is not

deteriorated. The deteriorated

rack may cause the unit to fall

down.

Ask an authorised dealer

to determine the level of

sterilisation function field settings

according to the local laws and

regulations.

Control panel

Do not wet the control panel.

Failure to do so may result in

electric shock and/or fire.

Do not press the buttons on the

control panel using hard and

sharp objects. Failure to do so

may cause damage to the unit.

Do not wash the control panel

using water, benzine, thinner or

scouring powder.

Do not inspect or maintain

the control panel by yourself.

Consult an authorised dealer in

order to prevent personal injury

caused by incorrect operation.

Safety precautions

F569727_SS0814-1.indb 5F569727_SS0814-1.indb 5 21/08/2014 10:54:09 AM21/08/2014 10:54:09 AM

Process BlackProcess Black

6

To adjust initial settings

Before Indoor Unit operate, its Capacity

Rank has to match with connected

Outdoor Unit. See below table for detail.

System Capacity Rank Setting

The Capacity Rank can be set by Control Panel

1

Press

and buttons simultaneously for 5

seconds.

2

Press

or button to select menu CAP RAN.

3

Press

button then press or button

to change capacity rank and press button to

confirm the outdoor capacity rank.

4

Press

button and Exit to home display.

Model

Capacity Rank

Indoor Unit Outdoor Unit

WH-ADC0309G3E5

WH-UD03EE5 3

WH-UD05EE5 5

WH-UD07FE5 7

WH-UD09FE5 9

Menu (1 ~ 15)

Setting Display

1

Room Thermostat Connection

To select whether or not to connect to the optional room thermostat.

YES NO

2

Indoor Backup Heater Selection

To reduce the heater power if unnecessary.

*Options of kW vary depending on the model.

*3 kW / 6 kW /

9 kW

3

Water System Freeze Prevention

To activate or deactivate the water freeze prevention when the system is OFF.

YES NO

4

*

1,

*

2

Cooling/Heating Operation Interval

To set the interval for COOL or HEAT mode during COOL + TANK or HEAT +

TANK mode.

0.5 hours ~

10 hours

5

*

1

Tank Heat-up Interval

To set the interval for the water tank during COOL + TANK or HEAT + TANK

mode.

5 minutes ~

1 hour 35 minutes

Dealer

Select menus and determine settings according to the system available in the

household. It is recommended that all alterations of settings are done by an

authorised dealer or specialist.

• After initial installation, you may manually adjust the settings.

The initial setting remains active until the user changes it.

• Ensure the operation LED is OFF before setting.

• The system may not work properly if set wrongly. Please consult

an authorised dealer.

1

Press and simultaneously and hold for

5 seconds until the display shows SETTING STATUS.

2

Press

or to select the menu.

3

Press

to enter the menu.

4

Press or to select Yes/No, or other options.

YES: to enable the menu

No: to disable the menu

5

Press to confirm.

Control Panel

DisplayOperation LED

F569727_SS0814-1.indb 6F569727_SS0814-1.indb 6 21/08/2014 10:54:09 AM21/08/2014 10:54:09 AM

Process BlackProcess Black

7

English

Dealer

Operation/settings to be done only by the authorised dealer/specialist.

User

Operation/settings to be done by the authorised dealer/specialist or user.

*

1

The system is locked to operate without COOL mode. It can be unlocked only by authorised installers or our authorised service partners.

*

2

Only displayed when COOL mode is unlocked (Means when COOL mode is available).

User

Control panel preparation

1

Press

.

2

Press or to set the current day.

3

Press

to confirm.

4

Repeat steps

2

and

3

to set the current time.

■ Note:

• The current day and time need to be set in cases below:

- When the power is turned on for the first time.

- A long time has elapsed since the power was turned on the

last time.

• The current time that has been set will be the standard time for

all the timer operations.

Caution Indicator (Tank Temperature above 60 °C)

6

Backup Heater For Tank

To activate backup heater during tank operation.

YES NO

• Do not use the system during sterilisation in order to prevent scalding with hot water, or overheating of shower.

• Ask an authorised dealer to determine the level of sterilisation function field settings according to the local laws and

regulations.

7

Sterilisation

To sterilise the water tank, if required.

Note: If NO is selected, menus 8 to 10 are skipped.

YES NO

8

Sterilisation Day & Time

To set timer for sterilisation.

(Only once a week. Operates even under a standby condition)

Monday ~

Sunday

0:00 ~ 23:50

9

Sterilisation Temperature

To set the temperature of sterilisation.

40 °C ~ 65 °C

10

Continuation of Sterilisation

To maintain heating temperature in order to complete the sterilisation.

5 minutes ~

1 hour

11

Base Pan Heater

To select whether or not to connect to the optional base pan heater.

Note: If NO is selected, menu 12 is skipped.

YES NO

12

Base Pan Heater type

Type A - The base pan heater activates only during deice operation.

Type B - The base pan heater activates when outdoor ambient temperature is

5 °C or lower.

AB

13

*

1,

*

2

Cool Outdoor Temperature setting

To set the outdoor ambient temperature for the AUTO mode to change from

HEAT to COOL.

5 °C ~ 25 °C

14

*

1,

*

2

Heat Outdoor Temperature setting

To set the outdoor ambient temperature for the AUTO mode to change from

COOL to HEAT.

5 °C ~ 25 °C

15

Dry Concrete

During construction to dry the concrete under a preset temperature.

Do not use this menu for any other purposes and in period other than during

construction (Refer to Information page).

1 day ~ 99 days

To adjust initial settings

F569727_SS0814-1.indb 7F569727_SS0814-1.indb 7 21/08/2014 10:54:11 AM21/08/2014 10:54:11 AM

Process BlackProcess Black

8

How to use

User

Enjoy quiet operation

Press .

• This operation reduces the noise of outdoor unit.

The operation may cause heating/

*

1

cooling ability to

decrease.

User

System status check mode

1

Press

.

(The display shows STATUS.)

2

Press or to check the selected mode.

• Dry concrete (does not show during normal

operation)

• The Water Inlet Temperature

• Tank Temperature

• Compressor Running Frequency

• Error History

• Heat mode total power consumption (Up to 999 days)

• *

1

Cool mode total power consumption (Up to 999 days)

• Tank mode total power consumption (Up to 999 days)

• Press

to exit the STATUS mode.

■ Note:

• Once the STATUS mode is entered, the display

shows STATUS.

• The STATUS mode cannot be activated when the

display shows SETTING.

• The total power consumption is an estimated value

based on AC 230 V and may differ from value

measured by precise equipment.

■ Note: In normal operation, the , and buttons are not in use.

User

Turn on or off the system

Press .

When the system is ON, the operation LED is lit and the

actual water outlet temperature and outdoor ambient

temperature are shown on the display.

User

Select operation mode

Press to select operation mode.

AUTO • Depending on the preset outdoor

temperature, the system selects HEAT or

*

1

COOL operation mode.

AUTO

+ TANK

• Depending on the preset outdoor

temperature, the system selects HEAT +

TANK or *

1

COOL

+ TANK operation mode.

HEAT • The outdoor unit provides heat to the

indoor unit.

HEAT

+ TANK

• The outdoor unit provides heat to the

sanitary water tank and indoor unit.

TANK • The outdoor unit provides heat to the

sanitary water tank.

COOL

+ TANK

• The outdoor unit provides cooling to the

indoor unit and heating to the sanitary

water tank.

COOL

• The panel is either turned ON or OFF.

• The outdoor unit provides cooling to the

indoor unit.

User

Initiate the backup heater

Press

.

• The backup heater provides extra heat at low outdoor

temperature. The backup heater is possible only in the

heat mode.

• Once the backup heater is set, it is automatically

operated when conditions are fulfilled.

• To disable the backup heater, press

again.

The system is turned off by an external switch.

*

1,

*

2

*

1,

*

2

F569727_SS0814-1.indb 8F569727_SS0814-1.indb 8 21/08/2014 10:54:13 AM21/08/2014 10:54:13 AM

Process BlackProcess Black

9

English

Dealer

Operation/settings to be done only by the authorised dealer/specialist.

User

Operation/settings to be done by the authorised dealer/specialist or user.

Dealer

System temperature setting

Temperature setting Display

The system controls the temperature for each menu based on the

outdoor ambient temperature.

• To set or change the temperatures, make sure to contact your

nearest authorised dealer.

1

Press and hold for 5 seconds to enter the

temperature range setting mode.

(The display shows SETTING.)

2

Press

or to select a menu.

3

Press to enter the menu.

4

Press or to set the desired temperature.

5

Press

to confirm the setting.

• Repeat steps

2

to

5

to set other menus.

User

Checking the temperature range

1

Press and hold

for 5 seconds to enter the temperature range setting mode.

2

Press

or to select a menu.

• Press

to exit.

Menu

Temperature

setting

Display

Setting of low outdoor ambient temperature. -15 °C ~ 15 °C

HEAT

Setting of high outdoor ambient temperature. -15 °C ~ 15 °C

Setting of water outlet temperature at low outdoor ambient

temperature.

25 °C ~ 55 °C

Setting of water outlet temperature at high outdoor ambient

temperature.

25 °C ~ 55 °C

During HEAT mode, the water outlet

temperature is adjusted as is shown the

diagram on the right.

It is performed within the preset temperature

range.

<Water outlet

temperature>

max. water temp.

min. water temp.

Setting of outdoor ambient temperature to turn OFF heating

operation during HEAT mode.

5 °C ~ 35 °C HEAT

Setting of outdoor ambient temperature to turn ON the backup

heater.

-15 °C ~ 20 °C HEATER

Setting of water outlet temperature during

*

1

COOL mode. 5 °C ~ 20 °C

*

1,

*

2

COOL

Setting of sanitary water tank temperature. 40 °C ~ 65 °C TANK

*

1

The system is locked to operate without COOL mode. It can be unlocked only by authorised installers or our authorised service partners.

*

2

Only displayed when COOL mode is unlocked (Means when COOL mode is available).

How to use

F569727_SS0814-1.indb 9F569727_SS0814-1.indb 9 21/08/2014 10:54:14 AM21/08/2014 10:54:14 AM

Process BlackProcess Black

10

How to use

User

Shifting the water temperature

Desired temperature setting

This easily shifts the water outlet temperature if the setting is

undesirable.

1

Press

to enter the water temperature shifting mode.

2

Press

to change setting.

3

Press

or to set the desired temperature.

(temperature range: -5 °C ~ 5 °C)

Temperature setting

+5

-5

Shift value

<Water outlet

temperature>

4

Press to confirm the setting.

■ Note:

• Press or wait for 30 seconds to exit the SETTING mode.

• The set temperature will be saved in the system once confirmed.

• The SETTING mode cannot be activated when the SERVICE and STATUS indicators are ON.

• The system will shift the temperature within water outlet temperature range.

User

Holiday mode

• By setting the day (s) in holiday mode, it promotes energy saving

while you are on holiday, and enables the system to resume at the

preset temperature after your holiday.

• Ensure that the system is OFF before setting.

• The system will resume operation automatically at 00:00 am after

the holiday.

• The day the HOLIDAY mode was set is counted as day 1.

Desired days

Example:

Setting the holiday mode on June 21, 08:00 am. By setting 3 days,

the system resumes operation on June 24, 00:00 am.

1

Press

to enter the HOLIDAY mode.

2

Press

or to set the desired days.

(Setting range: 1 day ~ 999 days)

3

Press to confirm the setting.

■ Note:

• Press or wait 30 seconds to exit the HOLIDAY mode.

F569727_SS0814-1.indb 10F569727_SS0814-1.indb 10 21/08/2014 10:54:16 AM21/08/2014 10:54:16 AM

Process BlackProcess Black

11

English

User

Weekly timer setting

Promotes energy saving by allowing you to set up to 6

programmes in any given day.

Indicates the next timer operation

programme

Day to be selected

Indicates the next timer

operation day

Programme number in a day

OFF Timer

ON Timer

Lights up if Timer operation is selected

1

Press

to enter the timer setting mode.

2

Press

or to select your desired day.

3

Press to confirm your selection.

4

“1” will be blinking, press

to set

programme 1.

5

Press to select ON or OFF timer.

6

Press or to select your desired time.

You can set

, , and the Water

Temperature Thermo Shift setting.

7

Press to confirm programme 1. The selected

day will be highlighted with ▼.

• After 2 seconds, the display will move to the

next programme. Repeat steps 4 to 7 to set

programmes 2 to 6.

• During timer setup, if no button is pressed within

30 seconds, or if the

is pressed, the setting at

that moment is confirmed and timer setup is ended.

To check current timer programme

1

Press

to enter timer mode and press

to enter day setting.

2

Press

or until your desired day is shown,

press

to confirm your selection.

3

Press

or to check the set programmes.

To modify current timer programme

or add new timer programme

1

Perform steps

1

to

7

of “Weekly timer

setting” to modify existing timer programme, or

add any timer programme.

To cancel current timer programme

1

Press to enter day.

2

Press

or until your desired day is shown,

press to enter programme setting.

3

Press

or until your desired programme is

shown.

Press

to cancel the programme and ▼ will

disappear.

To disable/enable Weekly Timer

• To disable weekly timer setting, press , then

press .

• To enable previous weekly timer setting, press ,

then press .

Dealer

Operation/settings to be done only by the authorised dealer/specialist.

User

Operation/settings to be done by the authorised dealer/specialist or user.

■ Note:

• You may set the timer for each day of the week (Monday to Sunday) with 6 programmes per day.

• When the system is switched on by the timer, it will use the previously set temperature to control the water outlet

temperature.

• The same timer programme cannot be set on the same day.

• You may also select 2 or more days with the same timer setting.

How to use

F569727_SS0814-1.indb 11F569727_SS0814-1.indb 11 21/08/2014 10:54:17 AM21/08/2014 10:54:17 AM

Process BlackProcess Black

12

Indoor unit

• Do not splash water directly.

Wipe the unit gently with a soft dry cloth.

Outdoor unit

• Do not obstruct the air inlet and outlet vents. Failure

to do so may result in low performance or system

breakdown. Remove any obstruction to assure the

ventilation.

• When it snows, clean and remove snow around the

outdoor unit to prevent the air inlet and outlet vents from

being covered with snow.

Non serviceable criteria

Disconnect the power supply

then please consult an authorised dealer under the

following conditions:

• Abnormal noise during operation.

• Water/foreign particles have entered the control panel.

• Water leaks from the indoor unit.

• Circuit breaker switches off frequently.

• Power cord becomes unnaturally warm.

For extended non-use

• The water inside the Sanitary Water Tank should be

drained.

• Disconnect the power supply.

MAINTENANCE

User

• In order to ensure optimal performance of the units, user may inspect and clear any obstruction on the air inlet and outlet

vents of the outdoor unit.

Dealer

• In order to ensure safety and optimal performance of the units, seasonal inspections on the units, functional check of

RCCB/ELCB, field wiring and piping have to be carried out at regular intervals by authorised dealer.

• Specific to the Sanitary Water Tank, it is important to service the Water Filter Set periodically and inspect the Anode

Bar annually. The Anode Bar which protects the tank body will corrode, depending on water quality. When diameter is

approximate 8mm, the Anode must be replaced.

• Users should not try to service or replace parts of the unit.

• Contact authorised dealer for scheduled inspection.

Cleaning instructions

To ensure optimal performance of the system, cleaning has to be carried out at regular intervals.

Consult an authorised dealer.

• Disconnect the power supply before cleaning.

• Do not use benzine, thinner or scouring powder.

• Use only soap (

pH7) or neutral household detergent.

• Do not use water hotter than 40 °C.

Water pressure gauge

• Do not press or hit the glass cover

using hard and sharp objects.

Failure to do so may cause

damage to the unit.

• Ensure that the water pressure

is between 0.05 and 0.3 MPa

(0.1 MPa = 1 bar).

• In case the water pressure is out

of the above range, consult an

authorised dealer.

Sanitary Water Tank

Anode Bar

Water Filter Set

F569727_SS0814-1.indb 12F569727_SS0814-1.indb 12 21/08/2014 10:54:19 AM21/08/2014 10:54:19 AM

Process BlackProcess Black

13

English

The following symptoms do not indicate malfunction.

Symptom Cause

Water flowing sound during operation. • Refrigerant flow inside the unit.

Operation is delayed a few minutes

after restarting.

• The delay is a protection for the compressor.

Outdoor unit emits water/steam. • Condensation or evaporation occurring in the pipes.

Steam comes out of the outdoor unit in

the heating mode.

• It is caused by defrost operation in the heat exchanger.

Outdoor unit does not operate. • It is caused by the protection control of the system when outdoor temperature is

out of the operating range.

System operation switches off. • It is caused by the protection control of the system. When the water inlet

temperature is lower than 10 °C, the compressor stops and the backup heater

power turns on.

System is hard to heat up. • When the panel and the floor are heated simultaneously, warm water temperature

may decrease, which may reduce the heating ability of the system.

• When the outdoor air temperature is low, the system may need longer time to heat

up.

• Discharge outlet or intake inlet in the outdoor unit is blocked by some obstacle,

such as a pile of snow.

• When the preset water outlet temperature is low, the system may need longer time

to heat up.

System does not heat up instantly. • System will take some time to heat up the water if it starts to operate at cold water

temperature.

Backup heater is automatically turned

ON when it is disabled.

• It is caused by the protection control of the indoor unit heat exchanger.

Operation starts automatically when the

timer is not set.

• Sterilisation timer has been set.

Display power consumption remains

as previous value.

• Memory is saved on hourly basis. If a power failure occurs, the data kept from last

hour will be displayed.

• Total power consumption has reached 999 days. press

to reset the counter.

HEAT indicator blinks on the display. • System is performing deice operation.

Loud refrigerant noise continue for a

few minutes.

• It is caused by protection control during deice operation at outdoor ambient

temperature lower than -10°C.

*

1

Cool mode is unavailable. • System has locked to operate in HEAT mode only.

Check the following before calling for servicing.

Symptom Check

Operation in HEAT/

*

1

COOL mode is

not working efficiently.

• Set the temperature correctly.

• Close the panel heater/cooler valve.

• Clear any obstruction in the air inlet and air outlet vents of the outdoor unit.

Noisy during operation. • Outdoor unit or indoor unit has been installed at an incline.

• Close the front plate properly.

System does not work. • Circuit breaker has tripped/activated.

Operation LED is not lit or nothing is

displayed on the control panel.

• Check that the power supply is working correctly, or that a power failure has not

occurred.

Troubleshooting

Force Heater Mode Button

• If a malfunction occurs in the system, the backup heater may be used to heat up the water.

Press to switch on the backup heater.

• Press

to switch off the backup heater.

• In the Force Heater mode, no other operation can be used.

*

1

The system is locked to operate without COOL mode. It can be unlocked only by authorised installers or our authorised service partners.

*

2

Only displayed when COOL mode is unlocked (Means when COOL mode is available).

Cleaning instructions / Troubleshooting

F569727_SS0814-1.indb 13F569727_SS0814-1.indb 13 21/08/2014 10:54:19 AM21/08/2014 10:54:19 AM

Process BlackProcess Black

14

*

1

The system is locked to operate without COOL mode. It can be unlocked only by authorised installers or our authorised service partners.

*

2

Only displayed when COOL mode is unlocked (Means when COOL mode is available).

The operation LED blinks and error code appears on

the display.

• Disconnect the power supply, and

report the error code to an authorised

dealer.

• The timer operation will be cancelled

when an error code is displayed.

Diagnostic

display

Abnormality or Protection

control works

H12

Capacity mismatch, Capacity rank not

set

H15

Abnormal compressor temperature

sensor

H20

Abnormal water pump

H23

Abnormal refrigerant 1 sensor

H27

Abnormal service valve

H42

Compressor low pressure protection

H62

Abnormal water flow

H63

Abnormal low pressure sensor

H64

Abnormal high pressure sensor

H65

Abnormal deice water circulation

H70

Abnormal back-up heater overload

protector

H72

Abnormal tank temperature sensor

H76

Control panel communication error

H90

Abnormal indoor / outdoor

communication

H91

Abnormal tank heater overload protector

H95

Abnormal voltage connection

H98

Outdoor high pressure protection

H99

Indoor heat exchanger freeze prevention

Diagnostic

display

Abnormality or Protection

control works

F12

Pressure switch activated

F14

Poor compressor rotation

F15

Abnormal outdoor fan motor lock

F16

Comprehensive current protection

F20

Compressor temperature overload

protection

F22

Transistor module temperature overload

protection

F23

DC peak abnormal of operation

F24

Abnormal Refrigerant cycle

F25

Abnormal in a

*

1

cooling / heating charge

F27

Abnormal pressure switch

F30

Abnormal water outlet sensor 2

F36

Abnormal outdoor air temperature

sensor

F37

Abnormal water inlet sensor

F40

Abnormal outdoor discharge sensor

F41

Abnormal power factor correction

F42

Abnormal outdoor heat exchanger

sensor

F43

Abnormal outdoor defrost sensor

F45

Abnormal water outlet sensor

F46

Abnormalities in outdoor current

transformer disconnection

F48

Abnormal evaporator outlet temperature

sensor

F49

Abnormal bypass outlet temperature

sensor

F95

Abnormal

*

1

cooling high pressure

Troubleshooting

F569727_SS0814-1.indb 14F569727_SS0814-1.indb 14 21/08/2014 10:54:19 AM21/08/2014 10:54:19 AM

Process BlackProcess Black

15

English

Information for Users on Collection and Disposal of Old Equipment

These symbols on the products, packaging, and/or accompanying documents mean that used electrical and

electronic products should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products, please take them to applicable collection points,

in accordance with your national legislation and the Directives 2002/96/EC and 2006/66/EC.

By disposing of these products correctly, you will help to save valuable resources and prevent any potential

negative effects on human health and the environment which could otherwise arise from inappropriate waste

handling.

For more information about collection and recycling of old products, please contact your local municipality,

your waste disposal service or the point of sale where you purchased the items.

Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.

For business users in the European Union

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further

information.

[Information on Disposal in other Countries outside the European Union]

These symbols are only valid in the European Union. If you wish to discard these items, please contact your

local authorities or dealer and ask for the correct method of disposal.

Information

Dry Concrete Function

• During construction to dry the concrete under a preset temperature.

1

Press

and simultaneously and hold for 5 seconds until the display shows “ ”.

2

Press

.

(The display shows “ ”).

3

Press

to select day.

Press

or to set the desired temperature.

4

Press to confirm the selection.

5

Repeat step

3

and

4

to set other days and temperature.

• Press

to exit.

Operation/settings to be done only by the authorised dealer/specialist.

Troubleshooting / Information

F569727_SS0814-1.indb 15F569727_SS0814-1.indb 15 21/08/2014 10:54:20 AM21/08/2014 10:54:20 AM

Process BlackProcess Black

Page is loading ...

Authorised representative in EU

Panasonic Testing Centre

Panasonic Marketing Europe GmbH

Winsbergring 15, 22525 Hamburg, Germany

Country Telephone Number Country Telephone Number

Bulgaria +359 (2) 971 2969 Nordic + Baltic +46 766 326 207

Croatia +385 (0) 800 777 986 Poland +48 723 991 164

France +33 825 362 193 Spain +34 902 153 060

Germany, Austria, Switzerland +49 800 200 2223 Turkey +90 444 7262

Hungary +36 402 0100

Italy +39 026 707 2556

Netherlands, Belgium, Luxemburg +31 (0) 6-4676 1041

F569727

SS0814-1

Printed in Malaysia

Panasonic Corporation

Web site: http://panasonic.net/

F569727_SS0814-1.indb 100F569727_SS0814-1.indb 100 21/08/2014 10:55:35 AM21/08/2014 10:55:35 AM

Process BlackProcess Black

Panasonic WH-ADC0309G3E5 Owner's manual

Panasonic WH-ADC0309G3E5 Owner's manual

in other languages

Related papers

Other documents