Page is loading ...
POOL LIGHT
UL - P100
(12V/75W)
VERZE 13. 11. 2017 / REVIZE: 13. 11. 2017
EN
INSTALLATION
AND USER GUIDE
Preparatory steps must be
performed by an electrician before
installing the light: see picture 1.
Make sure that the electrical system and its installation in the pool meet the requirements of the
relevant government standards or local authorities. The installation of the underwater light can only
be carried out by a qualified electrician.
• The connection box of the low-voltage transformer for the 12V model of the light must be placed
at least 120 cm from the edge of the pool, see picture 1.
• The light and all metal components placed 240 cm from the edge of the pool must be adequately
protected by non-flexible materials and the connections must be waterproof.
• The mounting bracket must be properly installed in a way that the top edge of the light lens is at
least 45 cm under the water level in the pool, see picture 1.
1.
1
2
PIC. 1
3
4
8
5
6
7
1
Connecting box for the light (not included)
2
Non-flexible conduit
3
Water level
4
There must be space for the compact sealing from the plaster around the recess in the concrete.
5
120 cm min.
6
Minimum 45 cm from the water level to the top edge of the lens
7
29,6 cm
8
6,6 cm
2 / Pool light UL - P100 (12V/75W)
2.
After meeting requirements
for the electrical electrical system,
carry out the following steps
1. Find a place on the vertical wall where you want to install the light. The top edge of the lens should
be placed 45 cm under the water level in the pool, see picture 1.
2. Connect the conduit to the centre of the mounting spacers (left of the console), see picture 2.
3. If the surface of the pool is to be plastered, you must subtract the finished plaster surface from
the thickness of the concrete. The completed surface of the concrete must be aligned with the
mounting spacers.
ATTENTION: The completed surface around the mounting spacers MUST BE flat and flush with the
surface of the mounting spacers. This ensures the perfect fit of the light to the wall of the pool, see
picture 3.
4. After finishing the surface of the pool, trim the conduit.
5. Roll the electric cable up in a way that its available length does not exceed 2.4 m. This excess cable
enables the removal of the light from the pool in order to replace the lamp and carry out a service.
6. Pull the cable through the conduit and connect the conductors in the junction box. While
connecting the conductors be careful not to pull more than 75-80 mm of the excess cable on the
light through the conduit.
7. Connect all conductors to the appropriate circuit conductors in the junction box and seal all the
connections with paran.
8. Attach the cover of the junction box.
9. Before turning the light on for longer than 10 seconds, fill the pool so that the light will be completely
immersed in the water. In order to check the correct functions, turn on the main switch or the
circuit breaker and also the switch that controls the light itself.
10. The secure attachment of the light to the console is ensured by turning on the safety system, see
picture 4.
Pool light UL - P100 (12V/75W) / 3
Winterisation
The light should remain in place during the winter.
3.
PIC. 2
1
2
3
PIC. 4
8 9
PIC. 3
4 5 6 7
1
Light
2
Mounting bracket
3
Conduit
4
Do not mount on surface with inverse
radius
5
Do not mount on irregular or uneven
surface
6
Mount on flat surface
7
Mount on walls with a radius that is not less
than 1.83 m when viewed from above
8
Open position
9
Closed position
4 / Pool light UL - P100 (12V/75W)
4.
List of parts
Item Amount Description
1 1 Coloured shade
2 1 Screw
3 1 Cover frame
4 1 Cover
5 1 Lens
6 1 Lens gasket
7 2 Sealing nut with a screw
8 1 Bulb 12 V/75 W
9 1 Bulb holder
10 1 Mirror
11 1 Head with a recess
12 1 O-ring seal
13 1 Body
14 8 Sealing nut with a screw
15 4 Screw
16 1 Lamp holder
17 1 Bracket for attachment to the wall
1
2
3
4
5
6
13
7
8
9
10
11
12
14
15
16
17
Pool light UL - P100 (12V/75W) / 5
Warranty conditions
Warranty conditions
The warranty conditions are governed by the commercial and warranty conditions of your supplier.
Safe liquidation of the product at the end of its useful life
Once the product’s useful life has ended, please ensure its ecological liquidation by a specialised company.
Complaints and Service
Claims are governed by the relevant acts on consumer protection.
In the event of any irreparable defects, please contact your supplier in writing.
Date ................................................................
Supplier
8.
WARNING
Never use this light for longer than 10 seconds if it isn’t completely immersed
under the water. If the assembled light is not completely immersed, it will become
very hot which can result in a serious injury to the users of the pool, plumbers and
passers-by, or damage to property.
Before installing or removing the lamp, the power supply must be switched o.
Before replacing, leave the lamp to cool down. This light uses a quartz halogen lamp.
Do not touch the lamp with bare hands; it might considerably shorten its lifetime. Use
the plastic protector that came with the replacement lamp in order not to touch the
lamp with your fingers.
DANGER!
RISK OF ELECTRIC SHOCK OR DEATH
This light must be installed by a qualified electrician or a qualified service engineer
in compliance with the requirements of the relevant government standards or
local authorities. Incorrect installation poses a hazard that could result in serious
injury, death or damage to property. Before servicing the light, disconnect the
power supply from the circuit breaker. Failure to follow these guidelines could
result in serious injury, death or damage to property.
6 / Pool light UL - P100 (12V/75W)
Notes
Pool light UL - P100 (12V/75W) / 7
Thank you
for using ALBIXON
products
ALBIXON
export@albixon.com
www.ALBIXON.com
Note that the photos used in the manual are illustrative only. Printing and typesetting errors reserved.
/
