AutoMotionShade EL-4270P Quick Reference Manual

Brand
AutoMotionShade
Model
EL-4270P
Type
Quick Reference Manual

AutoMotionShade EL-4270P is a device that allows you to program the limits of your car's sunshade. It has three wires that are connected to the dash switch, and a programmer (215P) is required to set the limits. The programmer has seven buttons:

  1. Left LED Light
  2. Right LED Light
  3. Left Program Button
  4. Right Program Button
  5. Save Button
  6. Delete Button
  7. Not being used

To program the limits, first connect the programmer to the white connector on the pig tail wire attached to the motor. Then, hold the UP or DOWN button on the Dash-Switch and press and hold either the left or right programming button on the programmer until the shade is about half-way up (or down). Press and hold the Delete button until the right LED light comes on, then release the Delete button. All old programs are now cleared.

AutoMotionShade EL-4270P is a device that allows you to program the limits of your car's sunshade. It has three wires that are connected to the dash switch, and a programmer (215P) is required to set the limits. The programmer has seven buttons:

  1. Left LED Light
  2. Right LED Light
  3. Left Program Button
  4. Right Program Button
  5. Save Button
  6. Delete Button
  7. Not being used

To program the limits, first connect the programmer to the white connector on the pig tail wire attached to the motor. Then, hold the UP or DOWN button on the Dash-Switch and press and hold either the left or right programming button on the programmer until the shade is about half-way up (or down). Press and hold the Delete button until the right LED light comes on, then release the Delete button. All old programs are now cleared.

410: R-2:07/19
Effective Date: July 15, 2019
Quick Reference Guide # 9
Programming Limits for second Generation Ignition-Lock Motor 4270P:
This motor has 3 wires only that are all connected to the Dash switch. To program the limits for Ignition-Lock
motor EL-4270P, a programmer (215P) is required as per shown below; the programmer needs to be connected
to the white connector on the pig tail wire attached to the motor, as illustrated.
Note 1: Motor model 4271P (earlier version), it is the same as motor model 4270P.
Note 2: Motor has two speeds when in programming mode, with the slow one being used for fine adjustment when coming close to the
desired limit (see also point no 3 below).
1. Regardless whether (dash) ignition switch position is on or off, connect the programmer and then hold the UP or
DOWN button on the Dash-Switch. You will need to keep holding dash-switch throughout the programming until
all programming steps up to no 6 are completed. The left LED (1) on programmer 215P should now be ON (if not,
it means there is no power to the shade or your programmer has no battery installed, in which case check
wiring).
2. Press and hold either the left (3) or right (4) programming button, until the shade is about half-way up (or
down). Press and hold ‘Delete’ button (6) until the right LED light (2) comes on then release the Delete button
(6). All old programs are now cleared.
3. Press and hold left programming button (3); the shade moves up until it reaches your desired top limit; if it goes
too fast/slow, you can release and press same button (3) again to switch to slower/faster speed. Once you reach
to top limit, release button (3); now press and hold ‘Save’ button (5) until right LED (2) comes ON, then release
it.
Programmer EL-215P
A
1
2
3
(1) Left LED Light
(2) Right LED Light
(3) Left Program Button
(4) Right Program Button
(5) Save Button
(6) Delete Button
(7) Not being used
4
5
6
7
410: R-2:07/19
Effective Date: July 15, 2019
4. Press and hold right programming button (4) to go down until you reach the bottom limit, then press and hold
‘Save’ button (5) until right LED (2) comes ON. Regular top and bottom shade limits are now set.
5. Next, program the intermediate safety stop (Ignition Line) by pushing and holding the left programming button
(3) again to move the shade to your desired intermediate safety stop that allows you to still safely see the road
when driving while using the shade as a sun visor.
6. When done, press and hold ‘Save’ button (5) until right LED (2) comes ON.
7. Disconnect the programmer by holding the connectors and not the wires (see Illustration above point A).
8. Release the dash switch you kept holding all along (see point 1).
9. Now test the end limits by operating the shade as follows:
- Ignition key is OFF: by pressing dash switch Up/Down, your shade should travel all the way from top
to bottom limit.
- Ignition key is ON: by pressing dash switch Up/Down, your shade should only travel to Ignition Limit
(see point 4 above) and should NOT travel beyond this point to prevent obstruction of your view
while driving.
Important Note:
The programmer needs to be disconnected after the programming process is done. Never leave the programmer
connected to the motor thereafter
  • Page 1 1
  • Page 2 2

AutoMotionShade EL-4270P Quick Reference Manual

Brand
AutoMotionShade
Model
EL-4270P
Type
Quick Reference Manual

AutoMotionShade EL-4270P is a device that allows you to program the limits of your car's sunshade. It has three wires that are connected to the dash switch, and a programmer (215P) is required to set the limits. The programmer has seven buttons:

  1. Left LED Light
  2. Right LED Light
  3. Left Program Button
  4. Right Program Button
  5. Save Button
  6. Delete Button
  7. Not being used

To program the limits, first connect the programmer to the white connector on the pig tail wire attached to the motor. Then, hold the UP or DOWN button on the Dash-Switch and press and hold either the left or right programming button on the programmer until the shade is about half-way up (or down). Press and hold the Delete button until the right LED light comes on, then release the Delete button. All old programs are now cleared.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents