Acterna FST-2000 TestPad Service Pack/Upgrade/Optioning Instructions

Brand
Acterna
Model
FST-2000 TestPad
Type
Service Pack/Upgrade/Optioning Instructions
FST-2000 TestPad Service Pack/Upgrade/Optioning Instructions 1
50-19345-01, Rev. A
Acterna FST-2000 TestPad
Service Pack/Upgrade/Optioning Instructions
This document describes how to load a V6 UIM Service Pack. It also
describes how to load software option and upgrades for
FST-2000 TestPad application modules that are compatible with
Version 6 (V6) and Version 3 (V3) user interface modules (UIMs).
Topics covered in this document include the following:
– “Getting started” on page 2
– “Loading a V6 UIM service pack” on page 2
– “Loading application module software upgrades” on page 3
– “Loading options for V6-compatible application modules” on
page 4
– “Loading options for V3-compatible application modules” on
page 5
– “Technical assistance” on page 6
Getting started
2 FST-2000 TestPad Service Pack/Upgrade/Optioning Instructions June 2004
Getting started
Acterna ships application module software upgrades, options, and
V6 UIM service packs on PCMCIA cards. You can also download soft-
ware upgrades and service packs from Acterna’s Customer Care or
FTP sites. Instructions for downloading upgrades or service packs
onto your PC or the TestPad are available on the sites.
Before you load a service pack, application module software upgrade,
or options, make sure the TestPad is connected to an AC adapter and
the adaptor is plugged in. Always use the AC adaptor that shipped with
your UIM. Using a different adaptor may damage the unit. Acterna also
recommends using a battery charged to at least 50 percent capacity
as a backup power supply.
Loading a V6 UIM service pack
The following procedure describes how to load a service pack for a V6
UIM.
To load a service pack
1 Make sure the application module is connected to the UIM.
2 Make sure the TestPad is OFF.
3 Connect the AC adaptor that shipped with your UIM to the
TestPad, and then plug the adaptor into a power source.
4 Do one of the following:
– Insert the PCMCIA card with the service pack into one of the
PCMCIA card slots located on the unit’s top panel.
– If you previously downloaded the service pack on to the
TestPad, you do not need to insert a PCMCIA card. Proceed to
step 5.
CAUTION: DAMAGE TO TESTPAD
When you load a service pack or software upgrade, the TestPad
loads the new software, and then automatically reboots. If power is
interrupted during this process, the TestPad may require factory
service to operate.
Loading application module software upgrades
June 2004 FST-2000 TestPad Service Pack/Upgrade/Optioning Instructions
3
5 Turn the TestPad power ON.
A series of boot-up screens appear as the TestPad powers on,
loads the service pack, and then automatically reboots.
When the main screen appears, the service pack is loaded.
Loading application module software upgrades
The following procedure describes how to load an application module
software upgrade. Loading a software upgrade can take up to one
hour.
To load an application module software upgrade
1 Make sure the application module is properly connected to the
UIM.
2 Make sure the TestPad is OFF.
3 Connect the AC adaptor that shipped with your UIM to the
TestPad, and then plug the adaptor into a power source.
4 Do one of the following:
– Insert the PCMCIA card with the software upgrade into one of
the PCMCIA card slots located on the unit’s top panel.
– If you previously downloaded the software upgrade on to the
TestPad, you do not need to insert a PCMCIA card. Proceed to
step 5.
5 Turn the TestPad power ON.
A series of boot-up screens appear as the TestPad powers on,
followed by a dialog box informing you that a newer version of
software has been detected for the application module. The dialog
box prompts you to upgrade the software.
6 Respond to the prompts as directed.
After all upgrade files are loaded, the TestPad automatically
reboots, and the main screen appears.
The application module software upgrade is loaded.
Loading options for V6-compatible application modules
4 FST-2000 TestPad Service Pack/Upgrade/Optioning Instructions June 2004
Loading options for V6-compatible application modules
You can purchase a variety of options for your UIM and application
module that expand your testing abilities and enhance your work
processes. Options are shipped on PCMCIA cards. If a software
upgrade is required for the options, the upgrade is also shipped on the
cards. You can load options onto your unit from a single card or from
two separate cards simultaneously.
To load options on a V6-compatible application module
1 Insert the PCMCIA card or cards with the options in a PCMCIA
card slot.
2 Turn the TestPad ON.
If the options you purchased require a software upgrade, you will
be prompted to upgrade the unit before loading the options. See
step 6 of “Loading application module software upgrades” on
page 3.
3 Select the Tools button, and then do one of the following:
– To load UIM options, select TestPad Settings, and then select
the Revisions/Options tab.
– To load application module options, select FST-XXXX
Settings, where XXXX represents the module number (for
example, FST-2310). The Revisions/Options tab appears.
Options currently installed on the TestPad appear under TestPad
Options or FST-XXXX Options.
4 Select Install Options.
The Options Installation dialog box appears, listing the options
available on the PCMCIA card (or cards).
The Number Remaining field indicates the remaining copies of the
option which are available for installation. Each time you install an
option, the TestPad decreases the number remaining by one.
Select the option or options you want to install.
NOTE:
If you inserted two PCMCIA optioning cards into the TestPad, and
both cards include the same option, the option appears twice in the
list of options.
Loading options for V3-compatible application modules
June 2004 FST-2000 TestPad Service Pack/Upgrade/Optioning Instructions
5
5 Select Install & Reboot.
The TestPad installs the options, and then the Install Options
dialog box appears, prompting you to press OK to reboot the unit.
6 Select OK.
The TestPad reboots and the options are available.
Loading options for V3-compatible application modules
The following procedure describes how to load options for an applica-
tion module that is compatible with a V3 UIM.
When you purchase options for your application module, the options
are shipped on a PCMCIA card. If a software upgrade is required for
the options, the upgrade is also shipped on the card. Before you begin
loading options, make sure the TestPad battery is charged to at least
50 percent. As a backup power supply, make sure the unit connected
to an AC power adaptor that is plugged in.
To load options on a V3-compatible application module
1 Make sure the TestPad is OFF.
2 Make sure the application module is properly connected to a
Version 3 UIM.
3 Insert the PCMCIA card with the options into one of the PCMCIA
card slots located on the unit’s top panel.
4 Turn the TestPad power ON.
The unit boots up and detects the card.
– If the options you purchased require a software upgrade, you
are prompted to upgrade the unit. See step 6 of “Loading appli-
cation module software upgrades” on page 3.
– If the unit already has the correct software release, it automati-
cally begins loading the options you purchased.
When the main screen appears, the options are loaded.
Technical assistance
6 FST-2000 TestPad Service Pack/Upgrade/Optioning Instructions June 2004
Global Headquarters
One Milestone Center Court
Germantown, Maryland 20876-7100 USA
Toll Free 1-800-638-2049 • Tel +1-240-404-2999 • Fax +1-240-404-2195
www.acterna.com
© Copyright 2004 Acterna, LLC. All rights reserved. Acterna, Communications Test and Management Solutions,
and its logo are trademarks of Acterna, LLC. All other trademarks and registered trademarks are the property of
their respective owners. Specifications, terms, and conditions are subject to change without notice.
Technical assistance
If you need assistance loading the service pack, upgrades or options,
contact Acterna’s Technical Assistance Center (TAC) at
1-800-638-2049. You can also contact your local sales office for
customer support. For current contact regional contact information,
visit www.acterna.com.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Acterna FST-2000 TestPad Service Pack/Upgrade/Optioning Instructions

Brand
Acterna
Model
FST-2000 TestPad
Type
Service Pack/Upgrade/Optioning Instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents