DARLEY SCREENGUARD Technical Manual

TECHNICAL MANUAL

SCREENGUARD

TM

Stainless Steel

Mesh Security System

A system by

12 december 2019

.

VERSION 2

Features and Benets �� 3

Technical Specications �� 3

Product Proles�� 4

Common Proles �� 4

Door Proles ��4

Window Proles �� 4

Tools and Equipment �� 5

Assembly �� 7

Stile Pre-Loading (Mesh Bow Reduction) �� 8

Fabricator’s Instructions �� 9

Stainless Mesh Deductions��9

Assembly ��9

Finished Size Window and Door Mesh

Deductions �� 10

Fabricator’s Instructions: Midrail �� 10

ScreenGuard Systems - Servery Window �� 11

Assembly Diagrams and Cross-Sections ��11

Introduction ��11

Hardware �� 12

Hinged Door Locks ��12

Flushbolts ��12

Hinged Door Closers ��12

Cylinders ��12

Hinges ��12

Sliding Door Locks ��13

Miscellaneous��13

Sliding Door Closers ��13

Rollers and Guides ��13

Cylinders ��13

Fabrication Guidance �� 14

Extra Instructional Resources ��14

Warranty & Maintenance �� 15

Screenguard Powawash��15

Care & Maintenance �� 15

Warranty ��15

Contents

DARLEY SCREENGUARD STAINLESS STEEL MESH SECURITY SYSTEM

3

Features and Benets

• No binding contracts or licensing

• No expensive machinery to manufacture

• Easy to fabricate, saves you time, labour and dollars

• Use of 316 marine grade stainless steel security mesh, low maintenance

• Competitive purchasing prices, more prots

• Your initial stock purchases are minimal

• Sales Brochures for retail assistance

More importantly,

This security door and window system released by Darley Aluminium has been

approved by an independent NATA accredited laboratory.

Technical Specications

1

1 See Warranty & Maintenance page for terms & conditions

Frame Type 6063 - T6 (Alloy Frame Temper)

Mesh Type 316 Grade Stainless Steel High-Tensile Woven

Security Mesh

Wire Diameter 0.8 mm (1.6mm overall sheet thickness)

Mesh Count 11 x 11 strands per inch

Aperture Size 1.64 mm x 1.64 mm (excluding coating)

Open Area 41.69% (excluding coating)

Warranty 10 year powder coat warranty on mesh*

DARLEY SCREENGUARD STAINLESS STEEL MESH SECURITY SYSTEM

4

Product Proles

Common Proles

AU01004

Mid Rail

2510

PVC 2-Part Wedge / Seat

Door Proles

AU01001

Door Frame

2655

Corner Stake (7.4mm)

To suit AU01001

Window Proles

AU01003

8mm Window Frame

AU01002

11mm Window Frame

2656

Corner Stake (7.4mm)

To Suit AU01002

2657

Corner Stake (4.8mm)

To Suit AU01003

2659

Nylon Corner

Stake

41,4

12,4

70,1

19,2

36,3

8

37

11

37

28

AU01006

Window Frame with Leg

DARLEY SCREENGUARD STAINLESS STEEL MESH SECURITY SYSTEM

5

Tools and Equipment

2910

Security Door Punch

2910-A

Air-Operated Security

Door Lock Punch

2912

Security Window

Center Punch

2920

Screenguard Hand Air Tool

2921

Wedge Insertion

Block

2515

Manual Wedge Assembly

Tool

2916-A

Air Operated Stake Punch

to Suit 2652

Floor stand sold separately:

(2916-FS)

2914

Window Corner Crimper

(Air Operated)

DARLEY SCREENGUARD STAINLESS STEEL MESH SECURITY SYSTEM

6

Tools and Equipment

2915

3-Point Lock Punch/Tool

2917

Drill Jig to Suit

Nylon Corner Stake 2659

2919

Drill Jig to Suit

Security Roller

2516

Moulded Replacement Block

to Suit 2515

2512

Portable Hammer Drill

2514

Moulded replacement

Block to Suit 2513

2513

Bit shaft with Moulded

Block To Suit 2512 Drill

DARLEY SCREENGUARD STAINLESS STEEL MESH SECURITY SYSTEM

7

Assembly

Step 1

L seat is mitred in corners as per

frame.

(Ensure L seat is inserted correctly).

Tip: - When inserting L seat, apply Lanotec. This can help speed up the process and make the job easier.

Step 2

Insert Stainless Steel Mesh.

Sheet to be supported to prevent

distortion and to help wedge insertion.

Refer to Diagram (1).

Tip: After stainless steel mesh has been cut to size, corner

tips can be cut at 45 degrees. This will help with the

insertion of the mesh.

Step 3

(1)

Tap in wedge using our manual tool,

automatic air tool or pneumatic hand

tool. Refer to diagrams (2) and (3).

(3)(2)

Tip 1: After the rst wedge has

been inserted, check and measure

your door/window widths (top,

center, bottom and diagonals).

Tip 2: Keep your wedge in its

original condition, store on a at

surface in a dry cool area.

- 4mm drain holes to be slotted in the bottom frame section. Red = Bottom Rail, Blue = Top Rail.

DARLEY SCREENGUARD STAINLESS STEEL MESH SECURITY SYSTEM

8

Stile Pre-Loading (Mesh Bow Reduction)

Screenguard Mesh may not be perfectly at. In sliding and hinged applications, the mesh

can be oriented to avoid any potential fouling, however, in the case of stacking doors,

center screen must remain at.

Pre-clamping the stiles as the wedge is inserted will allow the stiles to straighten the

mesh after releasing the clamp.

It is also possible to perform this pre-tensioning vertically rather than horizontally for

better results (increased tension), but will require a large clamp.

Clamping

(5 mm)

prior to wedge insertion

Stile pre-tension

pulls mesh taught

DARLEY SCREENGUARD STAINLESS STEEL MESH SECURITY SYSTEM

9

Fabricator’s Instructions

Stainless Mesh Deductions

Door Mesh = Door size less 106mm on width and height.

Window Mesh = Window size less 43mm on width and height.

Mesh with Midrails = Apply above deduction to whole mesh, apply 6mm less for

half panels (height only)

Assembly

1.1 After mitring window or door frame to required lengths, select the frame piece

that will be the bottom section and drill 3 drainage holes approximately 3-4mm in

diameter across internal seating section of door or window frame.

1.2 Once frame and mesh is cut to size, lay frame at on table with rubber L seat

inserted ready. L seat is to be mitred in corners as per frame. (Face side down).

Refer to Step 1 of Assembly)

1.3 Assembly 2 or 3 sides of frame together with corner stakes without riveting and

slip mesh into frame section on top of the L rubber seating.

Refer to Step 2 of Assembly.

2.1 Place 7mm thick medium to high density foam pvc matting under stainless mesh

sheet but not under any portion of the frame. (This will avoid any bellying of

mesh).

PVC foam matting should be used in a few places to provide adequate support to

the whole mesh.

2.2 Complete the frame - square up door or grille and rivet/screw corners as per

security industry standards

3.1 Measure the top and bottom frame rails with a wedge. Score wedge on 1 side

with Stanley knife and snap o at score. Tap in wedge using a solid pvc or similar

block, into the opposing sides. Finally measure remaining 2 lengths with wedge,

score and snap these lengths to complete door or window.

Refer to Step 3 of Assembly.

IMPORTANT:

Ensure matting is supporting mesh in the middle during whole wedge process.

Along with matting support the wedge process tensions in the mesh - if mesh sags

without the correct support it will not tension later. It is also important that the

support matting be 7mm and of a medium to high density as to support the mesh

without compressing under the weight. For best density we recommend “EVA 75”

foam.

DARLEY SCREENGUARD STAINLESS STEEL MESH SECURITY SYSTEM

10

Finished Size Window and Door Mesh Deductions

Finished Door Size

Deductions

Width

Height

106 mm

Width

Height

Finished Size

Deductions with Midrail

x

6mm6mm

x = Appropriate mesh

deduction (window / door)

Each half: Less 6mm

(height only)

Finished Door Size

Mesh Size

Finished Door Size

Mesh Size

Finished Window Size

Deductions

Finished Door Size

Mesh Size

Half Cut

43 mm

Fabricator’s Instructions: Midrail

Square cut Midrail AU01004 to 140mm o overall door size, midrail then inserted

between Door Frame AU01001

Finished Door Size

Deductions

Width

Height

106 mm

Width

Height

Finished Size

Deductions with Midrail

x

6mm6mm

x = Appropriate mesh

deduction (window / door)

Each half: Less 6mm

(height only)

Finished Door Size

Mesh Size

Finished Door Size

Mesh Size

Finished Window Size

Deductions

Finished Door Size

Mesh Size

Half Cut

43 mm

DARLEY SCREENGUARD STAINLESS STEEL MESH SECURITY SYSTEM

11

ScreenGuard Systems - Servery Window

We all love to entertain. Install a servery window to easily pass food from kitchen to

your external entertaining area, all with the convenience of ScreenGuard.

Introduction

Assembly Diagrams and Cross-Sections

2510-W100

DI3224

AU01002

Stainless

Steel Mesh

Cross Section

DI3224

15

23

Side View

INSIDE

OUTSIDE

2510-W100

DI3224

AU01002

Stainless

Steel Mesh

Cross Section

DI3224

15

23

Side View

2675

DT3020

Corner Stake

INSIDE

OUTSIDE

1705

2510-W100

DT3020

DI3224

AU01002

2510-R100

Stainless

Steel Mesh

Cross Section

DI3224

15

23

Side View

2675

DT3020

Corner Stake

INSIDE

OUTSIDE

DT3020

2686

10mm Guide Button

Nylon Button

2265

Keyless Servery Lock

2266

Keyed Servery Lock

2686

10mm Guide button

DARLEY SCREENGUARD STAINLESS STEEL MESH SECURITY SYSTEM

12

Hinged Door Locks

CODE DESCRIPTION

2105 8654 Hinged Sec Door Lock - No Cylinder

2105 - 3HS 8654 High - Sec 3 Point Lock Kit

2105 - 3ST 8654 Standard 3 Point Lock Kit

2105 - 3PK/PBT 8654 3 Point Lock Kit With Straight Bolts

2105 - EXT 8654 Extra Wide Strike

2224

Lockwood Anti Drill 5 Pin Cylinder - 45mm - K/

ALIKE * 20

CODE DESCRIPTION

2100 MK2 Hinged DoorLock - No Cylinder

2100 - 3ST MK2 Hinged DoorLock - No Cylinder

2100 - 3RV

MK2 Standard 3 Point Kit Bulk Lock

Height 950mm to 1050mm

2100 - EXT Extended Strike (Suits Whitco Tasman MK2)

2103-BL/PR/

WH

Quatro Hinged Security Door Lock

No Cylinder

2103-3ST Yale Quatro 3 Part Lock Kit

Cylinders

CODE DESCRIPTION

2200-P

2 x 5 Pin Cylinder

60mm K/Alike x 10

2201

2 x 5 Pin Cylinder

60mm K/Dier x 10

2220

2 x 5 Pin Cylinder

45mm K/Alike x 10

2223

2 x 5 Pin Cylinder

45mm K/Dier x 10

CODE DESCRIPTION

2204

Pin Cylinder - Key Alike

(Suits SD7 & Elegance Lock)

2205

Pin Cylinder - Key Dier

(Suits SD7 & Elegance Lock)

2221

Wafer Cylinder - Key Alike

(Suits SD7 & Elegance Lock)

2202

Pin Cylinder - Key Alike

(Suits Ultimate Lock)

2203

Pin Cylinder - Key Dier

(Suits Ultimate Lock)

CODE DESCRIPTION

2131 Ultimate Hinged Door Lock - No Cylinder

2131 - 3CH Cable Ultimate 3 Point High Kit

2131 - CH / S Cable Ultimate 3 Point Law Kit

2131 - 3CL Cable Ultimate 3 Point Law Kit

2131 - 3CL/S Cable Ultimate 3 Point Law Straight Kit

2131CT -SC Ultimate With Care Taker - No Cylinder

2156 Elegance Hinged Door Dock - No Cylinder

2156 - EXT Wide Striker Plate For Elegance

2156 - 3CH Elegance 3 - Point Cable High Kit

2156 - 3CL Elegance 3 - Point Cable Low Kit

2156 - 3C - ST150

Elegance 3 - Point Cable Kit

Short Top Less 150mm

2157 -3ADJ Elegance Adjustable 3 - Point Rod Kit

2120 HD7 Hinged Door Lock - No Cylinder

Flushbolts

CODE DESCRIPTION

2260 - BL Whitco 2 Part Flush Bolt - Black

1050 Austral Double Flushbolt For Security Door

CODE DESCRIPTION

2300 Whitco Hinge Door Closer (18kg max.)

2303 Lockwood 403 Hinge Door Closer - (21kg max.)

2301 Austral Hinge Door Closer

2305 Doric Hinge Door Closer (18kg max.)

Hinged Door Closers

CODE DESCRIPTION

2400 Security Door Hinges

2420 Hinges Packer 1mm Aluminium

2401

Lockwood 316

Stainless Steel Securtiy Door Hinge

2402

Lockwood 316 Stainless Steel

Security Door Hinge with Saftey Prong

Hinges

* Please check local branch for availability

DARLEY SCREENGUARD STAINLESS STEEL MESH SECURITY SYSTEM

13

CODE DESCRIPTION

2200-P

2 x 5 Pin Cylinder

60mm K/Alike x 10

2201

2 x 5 Pin Cylinder

60mm K/Dier x 10

2220

2 x 5 Pin Cylinder

45mm K/Alike x 10

2223

2 x 5 Pin Cylinder

45mm K/Dier x 10

CODE DESCRIPTION

2204

Pin Cylinder - Key Alike

(Suits SD7 & Elegance Lock)

2205

Pin Cylinder - Key Dier

(Suits SD7 & Elegance Lock)

2221

Wafer Cylinder - Key Alike

(Suits SD7 & Elegance Lock)

Sliding Door Locks

CODE DESCRIPTION

2155 - BL

Lockwood 8653 Sliding Door Lock-Black

No Cylinder

2155 -3PT Lockwood 8653 3 Point Lock Kit

2155 - STK

High Strength Strike to Suit 8653 Lock

Stainless Steel

CODE DESCRIPTION

2151 Austral SD7 Sliding Door - No Cylinder

2151 - 3CH Austral Cable SD7 3 - Point High Kit

2153 SD9 Horizon Sliding Door Lock

CODE DESCRIPTION

2265 - BL Servery Lock, Keyed

2266 - BL Servery Lock, Keyless

2290 Whitco Keyed Sliding Push Lock - K/N 32381

2145 Sliding Push Lock, “CYL4” Cylinder

2298 Double Cylinder Deadbolt

2392 Sliding Door Outer Pool

Miscellaneous

CODE DESCRIPTION

2450

Anthony Innovations: “Auz-t”

Security Door Roller

2451 Heavy Duty Oset Roller-30kg

2862 Security Door Top Guide to Suit 23.5mm

2863 Security Door Top Guide To Suit 21.2mm

2685

Security Door Corner Gyide Nylon

(Suit DF001/003/006, PTD001)

2686 10mm Guide Button For Servery Track

Rollers and Guides

CODE DESCRIPTION

2150

Whitco Leichhardt Sliding Door Lock

No Cylinder

2150 - 3ST

Whitco Leichhardt Standard Triple Lock Kit

Lock

Height 1050 to 1150mm

2150 - 3RV

Whitco Leichhardt Reverse Triple Lock Kit Lock

Height 950 to 1050mm

2165 Leichhardt 2 Point Lock - No Cylinder

Cylinders

Sliding Door Closers

* Please check local branch for availability

CODE DESCRIPTION

2360 “Easy Close” Sliding Door Closer

2380 “Inventco Water” Sliding Door Closer

2375 Anthony Innovations Soft Door Closer

DARLEY SCREENGUARD STAINLESS STEEL MESH SECURITY SYSTEM

14

Fabrication Guidance

Extra Instructional Resources

2910 Security Door Lock Punch 2910 & 2916 Air Operated Stake Punch vs 2920 Hand Air

Tool:

https://www.youtube.com/watch?v=d0jfeNGhsd0&t

or search: “Fabricating a Screenguard Security Door in less than 16 minutes!”

2910 Security Door Lock Punch Demonstration

https://www.youtube.com/watch?v=Awd8TwKsz9Q

or search: “2910 Security Door Punch Operation Demo”

DARLEY SCREENGUARD STAINLESS STEEL MESH SECURITY SYSTEM

15

Warranty & Maintenance

Warranty

Care & Maintenance

Screenguard product warranty is for 10 years from the date of product installation.

This warranty is to the original purchaser providing always that the product care

and maintenance recommendations have been complied with during that

period. Screenguard warrants its product to be free from defects in materials and

manufacturing when fabricated in accordance with the Screenguard fabricator

instructions. This warranty does not apply to damage caused by abuse, re, accident,

acts of god or alteration to the original product in any part

Your Screenguard Security System will require regular maintenance to remove

contaminants caused by pollution, industry, salt and climatic conditions. It is

recommended to use a soft bristled brush or non-abrasive cloth with warm potable

water and neutral detergent, then rinse with potable water. Abrasive cleaners and

harsh detergents are not recommended as these can scratch or damage the surface

area. The following table indicates the suggested frequency of maintenance.

Environment Denition Frequency

Mild 10km from coastal/rural or suburban areas Every 6 months

Moderate 5km from coastal/high trac areas Every 3 months

Severe / Coastal 1km from coastal/marine/heavy industrial Every 2 weeks

Screenguard Powawash

Regular maintenance with ScreenGuard Powawash is

required to comply with your Screenguard 10 year

warranty.

Mix 3 caps (25mL) per litre of water. It is

recommended to use a soft bristled brush or

non-abrasive cloth, then rinse with water.

Screenguard Powawash is:

Non - Toxic

Biodegradable

User-Friendly

Environmentally Friendly

200ml per bottle

DARLEY SCREENGUARD STAINLESS STEEL MESH SECURITY SYSTEM

16

Corner Stake Punch – Model HP-160-06K

The process of locking Corner Stakes into security door corners has always been a labour intensive problem.

(Most manufacturers drill the frames and then use pop rivets to secure the corners.)

The use of Reinforced Plastic Corner Stakes has changed the industry - less time consuming - easier to assemble.

The Universal Hole punch is designed to provide an easy and safe solution to enable the screw holes to be

accurately punched in each frame end in about 1 second. Result - a neat clean joint without distortion.

What you get:

Each kit contains the portable Hole Punch , Foot Valve and the necessary tube and fittings.

Specifications:

 The machine is designed to crimp the corners of Security Window Frames to the Aluminium Corner Stakes.

 The accepted range for frame thickness is 8-12 mm.

(Important - The corner stake thickness should be a tight fit - less than 0.2 mm clearance.

 The operating pressure is a minimum of 7 bar.

Installation Instructions:

1. Place the corner press onto the bench or wall location.

2. Connect the tubing between the press and the foot valve.

3. Connect the air supply to the foot valve and you are ready to go.

Operating Instructions:

1. Slide the mitred end of the soor section into the press – fully in against the stop

2. Press the foot pedal to crimp the corner.

3. Release the foot pedal and remove the frame.

Follow the above procedure for each frame end.

Universal Fluid Power Pty Ltd

A C N 42 050 407 415  +61 7 3202 9000

P O Box 1440, Kenmore, QLD 4069, Australia

 info@univer.com.au

Issue date 28/10/2019

Corner Stake Punch - 2916

The process of locking corner stakes into security door corners has always been a labour

intensive problem. Most manufacturers drill the frames and then use pop rivets to secure the

corners.

The use of Reinforced Plastic Corner Stakes has changed the industry - less time consuming -

easier to assemble.

The Universal Holy punch is designed to provide an easy and safe solution to enable the

screw holes to be accurately punched in each frame and end in about 1 second.

What You Get:

Each kit contains the portable Hole Punch, Foot Valve and the neccessary tube and ttings.

The operating pressure is a minimum of 7 bar.

Installation Instructions:

1. Place the corner press onto the bench or wall location.

2. Connect the tubing between the press and the foot valve.

3. Connect the air supply to the foot valve.

Operating Instructions:

1. Slide the mitred end of the door section into the press - fully in against the stop.

2. Press the foot pedal to crimp the corner.

3. Release the foot pedal and remove the frame.

Follow the above procedure for each frame end

Use and maintenance manual

Reproduction or translation of any part of this handbook without the prior written authorisation of the owner is

prohibited. The information and the illustrations contained in this manual are purely indicative. COMALL

INTERNATIONAL s.r.l. reserves the right to modify the product without prior notice.

Code

MUX12216_GB

REV. 04

©

DARLEY SCREENGUARD STAINLESS STEEL MESH SECURITY SYSTEM

18

Code ZOX14861

Use and maintenance manual Page 5 of 24

Warnings and symbols used:

Read this manual carefully, especially the safety warnings, before using the machine. Keep it

in a suitable place and keep it intact.



If assistance is needed contact our company only.



CAUTION: draws attention to situations and problems connected with correct machine

operation.

DANGER: draws attention to situations and problems that may compromise personal safety.

OPERATOR: we mean the person who received an adequate training before of the use of the punching

machine.

QUALIFIED PERSONNEL: refers to personnel whose profession it is to work on plant, such as for example,

electricians, plumbing and heating engineers, etc. or trained maintenance

technicians appointed by the user.

AUTHORISED PERSONNEL: refers to personnel provided by Comall to carry out replacement, modification

sed sa enihcam eht no ecnanetniam yranidroartxe ro cribed in this manual.

W

ARRANTY

The manufacturer guarantees that the punching machine supplied has been tested with positive results. The

Warranty lasts for 12 months and is limited to the good quality of materials and the absence of constructional

defects. The client has the right to replacement of any defective parts only, excluding the cost of carriage,

packing and any labour for replacing parts. The warranty therefore does not cover damage due to dropping,

tampering with or incorrect operati

on of the punching machine, failure to observe the maintenance rules

stated in the use and maintenance manual, as well as incorrect actions by the operator, so as the use of

“COMALL” spare parts not original. Moreover the spare parts not original can cause a structural collapse with

consequent risk of accidents and serious injuries. No compensation shall be given for any periods during

which the punching machine remains inactive. The warranty is conditional

upon the terms of payment having

been satisfied. Charges for the assistance provided, together with the cost of spare parts used that do not

fall within the clauses of the warranty, shall be payable directly to the technician carrying out the work, who

will issue a service receipt to be followed by a proper invoice. The hourly rates for work carried out and the

cost of spare parts used will be in accordance with the current price list.

DARLEY SCREENGUARD STAINLESS STEEL MESH SECURITY SYSTEM

19

Code ZOX14861

Use and maintenance manual Page 7 of 24

2

T

E

C

H

N

I

C

A

L

D

A

T

A

2.1 Technical characteristics

Description Unit of

measurement

Value

090Ø mm rednilyC

2 srebmahc fo rebmuN

5,9 mm ekorts rednilyC

4 raB erusserp gnikrow muminiM

024 .gK ecrof gnihcnuP

Air consumption Nl per cycle 0,13

Dimensions mm 409X173,5 H235

6,5 .gK thgieW

NOISE EMISSION OF THE PUNCHING MACHINE

NOISE VALUES ACCORDING TO ISO 3746

)Bd2-/+( 1,501 : ) A ( Bd level rewop dnuoS awL

Lpa Sound pressure level at operator station dB ( A ) : 98,6 (+/-2dB)

Use personal protective equipment complying with current legislation.

2.2 Components and connections

No. Description

1. Punching machine

2. Profile support

3. Profile support

DARLEY SCREENGUARD STAINLESS STEEL MESH SECURITY SYSTEM

20

Code ZOX14861

Use and maintenance manual Page 8 of 24

3

I

N

S

T

A

L

A

T

I

O

N

3.1 Installation

Before installing the punching machine, check for any visible damage. If there is any, do not

install the punching machine and do not use it, but contact COMALL service assistance.

Check that the package contains all the components listed in the previous chapter. If any parts

are missing contact COMALL service assistance.

The punching machine must be installed by qualified personnel, placing the bench on a flat,

solid surface (cement or similar).

3.1.1 Preparing the machine

Remove the packaging from the machine and

dispose of it conforming to current legislation.

3.1.2 Compressed air connection

PRELIMINARY OPERATION

To put the machine into service, check that the factory compressed air supply is equipped

with hoses of suitable diameter for the flow required and a stop cock (valve) before the

punching machine. Do not connect up the punching machine at a distance greater than 3

metres from the compressed air supply. Do not connect up the punching machine to the

air supply without a pressure switch, pressure regulator, gauge, and condensation drain.

IT IS OBLIGA

TORY TO MAKE SURE THE CONNECTIONS ARE CORRECT BEFORE

SUPPLYING THE MACHINE WITH POWER.

CAUTION

Before introducing air into the punching machine circuit, check the oil level in the intake

filter through the glass; if necessary, top up by undoing the relative reservoir.

Check that the air supply is the same as what is stated in the “technical specifications”

table.

Connect the air supply directly to the

control on the punching machine or to

the filter unit according to the layout

shown in the figure.

Page is loading ...

DARLEY SCREENGUARD Technical Manual

This manual is also suitable for

DARLEY SCREENGUARD Technical Manual

Other documents