DARLEY 2920 Technical Manual

Type
Technical Manual

This manual is also suitable for

TECHNICAL MANUAL
SCREENGUARD
TM
Stainless Steel
Mesh Security System
A system by
12 december 2019
.
VERSION 2
Features and Benets ������������������������������������ 3
Technical Specications �������������������������������������� 3
Product Proles����������������������������������������������� 4
Common Proles ������������������������������������������������� 4
Door Proles ��������������������������������������������������������4
Window Proles ��������������������������������������������������� 4
Tools and Equipment �������������������������������������� 5
Assembly ���������������������������������������������������������� 7
Stile Pre-Loading (Mesh Bow Reduction) ����� 8
Fabricator’s Instructions �������������������������������� 9
Stainless Mesh Deductions���������������������������������9
Assembly ���������������������������������������������������������������9
Finished Size Window and Door Mesh
Deductions ����������������������������������������������������� 10
Fabricator’s Instructions: Midrail ��������������� 10
ScreenGuard Systems - Servery Window ��� 11
Assembly Diagrams and Cross-Sections ���������11
Introduction ��������������������������������������������������������11
Hardware ������������������������������������������������������� 12
Hinged Door Locks ��������������������������������������������12
Flushbolts �����������������������������������������������������������12
Hinged Door Closers �����������������������������������������12
Cylinders �������������������������������������������������������������12
Hinges �����������������������������������������������������������������12
Sliding Door Locks ���������������������������������������������13
Miscellaneous�����������������������������������������������������13
Sliding Door Closers ������������������������������������������13
Rollers and Guides ���������������������������������������������13
Cylinders �������������������������������������������������������������13
Fabrication Guidance ����������������������������������� 14
Extra Instructional Resources ��������������������������14
Warranty & Maintenance ���������������������������� 15
Screenguard Powawash������������������������������������15
Care & Maintenance ������������������������������������������ 15
Warranty �������������������������������������������������������������15
Contents
DARLEY SCREENGUARD STAINLESS STEEL MESH SECURITY SYSTEM
3
Features and Benets
No binding contracts or licensing
No expensive machinery to manufacture
Easy to fabricate, saves you time, labour and dollars
Use of 316 marine grade stainless steel security mesh, low maintenance
Competitive purchasing prices, more prots
Your initial stock purchases are minimal
Sales Brochures for retail assistance
More importantly,
This security door and window system released by Darley Aluminium has been
approved by an independent NATA accredited laboratory.
Technical Specications
1
1 See Warranty & Maintenance page for terms & conditions
Frame Type 6063 - T6 (Alloy Frame Temper)
Mesh Type 316 Grade Stainless Steel High-Tensile Woven
Security Mesh
Wire Diameter 0.8 mm (1.6mm overall sheet thickness)
Mesh Count 11 x 11 strands per inch
Aperture Size 1.64 mm x 1.64 mm (excluding coating)
Open Area 41.69% (excluding coating)
Warranty 10 year powder coat warranty on mesh*
DARLEY SCREENGUARD STAINLESS STEEL MESH SECURITY SYSTEM
4
Product Proles
Common Proles
AU01004
Mid Rail
2510
PVC 2-Part Wedge / Seat
Door Proles
AU01001
Door Frame
2655
Corner Stake (7.4mm)
To suit AU01001
Window Proles
AU01003
8mm Window Frame
AU01002
11mm Window Frame
2656
Corner Stake (7.4mm)
To Suit AU01002
2657
Corner Stake (4.8mm)
To Suit AU01003
2659
Nylon Corner
Stake
41,4
12,4
70,1
19,2
36,3
8
37
11
37
28
AU01006
Window Frame with Leg
DARLEY SCREENGUARD STAINLESS STEEL MESH SECURITY SYSTEM
5
Tools and Equipment
2910
Security Door Punch
2910-A
Air-Operated Security
Door Lock Punch
2912
Security Window
Center Punch
2920
Screenguard Hand Air Tool
2921
Wedge Insertion
Block
2515
Manual Wedge Assembly
Tool
2916-A
Air Operated Stake Punch
to Suit 2652
Floor stand sold separately:
(2916-FS)
2914
Window Corner Crimper
(Air Operated)
DARLEY SCREENGUARD STAINLESS STEEL MESH SECURITY SYSTEM
6
Tools and Equipment
2915
3-Point Lock Punch/Tool
2917
Drill Jig to Suit
Nylon Corner Stake 2659
2919
Drill Jig to Suit
Security Roller
2516
Moulded Replacement Block
to Suit 2515
2512
Portable Hammer Drill
2514
Moulded replacement
Block to Suit 2513
2513
Bit shaft with Moulded
Block To Suit 2512 Drill
DARLEY SCREENGUARD STAINLESS STEEL MESH SECURITY SYSTEM
7
Assembly
Step 1
L seat is mitred in corners as per
frame.
(Ensure L seat is inserted correctly).
Tip: - When inserting L seat, apply Lanotec. This can help speed up the process and make the job easier.
Step 2
Insert Stainless Steel Mesh.
Sheet to be supported to prevent
distortion and to help wedge insertion.
Refer to Diagram (1).
Tip: After stainless steel mesh has been cut to size, corner
tips can be cut at 45 degrees. This will help with the
insertion of the mesh.
Step 3
(1)
Tap in wedge using our manual tool,
automatic air tool or pneumatic hand
tool. Refer to diagrams (2) and (3).
(3)(2)
Tip 1: After the rst wedge has
been inserted, check and measure
your door/window widths (top,
center, bottom and diagonals).
Tip 2: Keep your wedge in its
original condition, store on a at
surface in a dry cool area.
- 4mm drain holes to be slotted in the bottom frame section. Red = Bottom Rail, Blue = Top Rail.
DARLEY SCREENGUARD STAINLESS STEEL MESH SECURITY SYSTEM
8
Stile Pre-Loading (Mesh Bow Reduction)
Screenguard Mesh may not be perfectly at. In sliding and hinged applications, the mesh
can be oriented to avoid any potential fouling, however, in the case of stacking doors,
center screen must remain at.
Pre-clamping the stiles as the wedge is inserted will allow the stiles to straighten the
mesh after releasing the clamp.
It is also possible to perform this pre-tensioning vertically rather than horizontally for
better results (increased tension), but will require a large clamp.
Clamping
(5 mm)
prior to wedge insertion
Stile pre-tension
pulls mesh taught
DARLEY SCREENGUARD STAINLESS STEEL MESH SECURITY SYSTEM
9
Fabricator’s Instructions
Stainless Mesh Deductions
Door Mesh = Door size less 106mm on width and height.
Window Mesh = Window size less 43mm on width and height.
Mesh with Midrails = Apply above deduction to whole mesh, apply 6mm less for
half panels (height only)
Assembly
1.1 After mitring window or door frame to required lengths, select the frame piece
that will be the bottom section and drill 3 drainage holes approximately 3-4mm in
diameter across internal seating section of door or window frame.
1.2 Once frame and mesh is cut to size, lay frame at on table with rubber L seat
inserted ready. L seat is to be mitred in corners as per frame. (Face side down).
Refer to Step 1 of Assembly)
1.3 Assembly 2 or 3 sides of frame together with corner stakes without riveting and
slip mesh into frame section on top of the L rubber seating.
Refer to Step 2 of Assembly.
2.1 Place 7mm thick medium to high density foam pvc matting under stainless mesh
sheet but not under any portion of the frame. (This will avoid any bellying of
mesh).
PVC foam matting should be used in a few places to provide adequate support to
the whole mesh.
2.2 Complete the frame - square up door or grille and rivet/screw corners as per
security industry standards
3.1 Measure the top and bottom frame rails with a wedge. Score wedge on 1 side
with Stanley knife and snap o at score. Tap in wedge using a solid pvc or similar
block, into the opposing sides. Finally measure remaining 2 lengths with wedge,
score and snap these lengths to complete door or window.
Refer to Step 3 of Assembly.
IMPORTANT:
Ensure matting is supporting mesh in the middle during whole wedge process.
Along with matting support the wedge process tensions in the mesh - if mesh sags
without the correct support it will not tension later. It is also important that the
support matting be 7mm and of a medium to high density as to support the mesh
without compressing under the weight. For best density we recommend “EVA 75”
foam.
DARLEY SCREENGUARD STAINLESS STEEL MESH SECURITY SYSTEM
10
Finished Size Window and Door Mesh Deductions
Finished Door Size
Deductions
Width
Height
106 mm
106 mm
Width
Height
Finished Size
Deductions with Midrail
x
x
6mm6mm
x = Appropriate mesh
deduction (window / door)
Each half: Less 6mm
(height only)
Finished Door Size
Mesh Size
Finished Door Size
Mesh Size
Finished Window Size
Deductions
Finished Door Size
Mesh Size
Half Cut
43 mm
43 mm
Fabricator’s Instructions: Midrail
Square cut Midrail AU01004 to 140mm o overall door size, midrail then inserted
between Door Frame AU01001
Finished Door Size
Deductions
Width
Height
106 mm
106 mm
Width
Height
Finished Size
Deductions with Midrail
x
x
6mm6mm
x = Appropriate mesh
deduction (window / door)
Each half: Less 6mm
(height only)
Finished Door Size
Mesh Size
Finished Door Size
Mesh Size
Finished Window Size
Deductions
Finished Door Size
Mesh Size
Half Cut
43 mm
43 mm
DARLEY SCREENGUARD STAINLESS STEEL MESH SECURITY SYSTEM
11
ScreenGuard Systems - Servery Window
We all love to entertain. Install a servery window to easily pass food from kitchen to
your external entertaining area, all with the convenience of ScreenGuard.
Introduction
Assembly Diagrams and Cross-Sections
2510-W100
DI3224
AU01002
Stainless
Steel Mesh
Cross Section
DI3224
15
23
Side View
INSIDE
OUTSIDE
2510-W100
DI3224
AU01002
Stainless
Steel Mesh
Cross Section
DI3224
15
23
Side View
2675
DT3020
DT3020
Corner Stake
INSIDE
INSIDE
OUTSIDE
1705
2510-W100
DT3020
DI3224
AU01002
2510-R100
Stainless
Steel Mesh
Cross Section
DI3224
15
23
Side View
2675
DT3020
DT3020
Corner Stake
INSIDE
INSIDE
OUTSIDE
OUTSIDE
DT3020
2686
10mm Guide Button
Nylon Button
2265
Keyless Servery Lock
2266
Keyed Servery Lock
2686
10mm Guide button
DARLEY SCREENGUARD STAINLESS STEEL MESH SECURITY SYSTEM
12
Hinged Door Locks
CODE DESCRIPTION
2105 8654 Hinged Sec Door Lock - No Cylinder
2105 - 3HS 8654 High - Sec 3 Point Lock Kit
2105 - 3ST 8654 Standard 3 Point Lock Kit
2105 - 3PK/PBT 8654 3 Point Lock Kit With Straight Bolts
2105 - EXT 8654 Extra Wide Strike
2224
Lockwood Anti Drill 5 Pin Cylinder - 45mm - K/
ALIKE * 20
CODE DESCRIPTION
2100 MK2 Hinged DoorLock - No Cylinder
2100 - 3ST MK2 Hinged DoorLock - No Cylinder
2100 - 3RV
MK2 Standard 3 Point Kit Bulk Lock
Height 950mm to 1050mm
2100 - EXT Extended Strike (Suits Whitco Tasman MK2)
2103-BL/PR/
WH
Quatro Hinged Security Door Lock
No Cylinder
2103-3ST Yale Quatro 3 Part Lock Kit
Cylinders
CODE DESCRIPTION
2200-P
2 x 5 Pin Cylinder
60mm K/Alike x 10
2201
2 x 5 Pin Cylinder
60mm K/Dier x 10
2220
2 x 5 Pin Cylinder
45mm K/Alike x 10
2223
2 x 5 Pin Cylinder
45mm K/Dier x 10
CODE DESCRIPTION
2204
Pin Cylinder - Key Alike
(Suits SD7 & Elegance Lock)
2205
Pin Cylinder - Key Dier
(Suits SD7 & Elegance Lock)
2221
Wafer Cylinder - Key Alike
(Suits SD7 & Elegance Lock)
2202
Pin Cylinder - Key Alike
(Suits Ultimate Lock)
2203
Pin Cylinder - Key Dier
(Suits Ultimate Lock)
CODE DESCRIPTION
2131 Ultimate Hinged Door Lock - No Cylinder
2131 - 3CH Cable Ultimate 3 Point High Kit
2131 - CH / S Cable Ultimate 3 Point Law Kit
2131 - 3CL Cable Ultimate 3 Point Law Kit
2131 - 3CL/S Cable Ultimate 3 Point Law Straight Kit
2131CT -SC Ultimate With Care Taker - No Cylinder
2156 Elegance Hinged Door Dock - No Cylinder
2156 - EXT Wide Striker Plate For Elegance
2156 - 3CH Elegance 3 - Point Cable High Kit
2156 - 3CL Elegance 3 - Point Cable Low Kit
2156 - 3C - ST150
Elegance 3 - Point Cable Kit
Short Top Less 150mm
2157 -3ADJ Elegance Adjustable 3 - Point Rod Kit
2120 HD7 Hinged Door Lock - No Cylinder
Flushbolts
CODE DESCRIPTION
2260 - BL Whitco 2 Part Flush Bolt - Black
1050 Austral Double Flushbolt For Security Door
CODE DESCRIPTION
2300 Whitco Hinge Door Closer (18kg max.)
2303 Lockwood 403 Hinge Door Closer - (21kg max.)
2301 Austral Hinge Door Closer
2305 Doric Hinge Door Closer (18kg max.)
Hinged Door Closers
CODE DESCRIPTION
2400 Security Door Hinges
2420 Hinges Packer 1mm Aluminium
2401
Lockwood 316
Stainless Steel Securtiy Door Hinge
2402
Lockwood 316 Stainless Steel
Security Door Hinge with Saftey Prong
Hinges
* Please check local branch for availability
DARLEY SCREENGUARD STAINLESS STEEL MESH SECURITY SYSTEM
13
CODE DESCRIPTION
2200-P
2 x 5 Pin Cylinder
60mm K/Alike x 10
2201
2 x 5 Pin Cylinder
60mm K/Dier x 10
2220
2 x 5 Pin Cylinder
45mm K/Alike x 10
2223
2 x 5 Pin Cylinder
45mm K/Dier x 10
CODE DESCRIPTION
2204
Pin Cylinder - Key Alike
(Suits SD7 & Elegance Lock)
2205
Pin Cylinder - Key Dier
(Suits SD7 & Elegance Lock)
2221
Wafer Cylinder - Key Alike
(Suits SD7 & Elegance Lock)
Sliding Door Locks
CODE DESCRIPTION
2155 - BL
Lockwood 8653 Sliding Door Lock-Black
No Cylinder
2155 -3PT Lockwood 8653 3 Point Lock Kit
2155 - STK
High Strength Strike to Suit 8653 Lock
Stainless Steel
CODE DESCRIPTION
2151 Austral SD7 Sliding Door - No Cylinder
2151 - 3CH Austral Cable SD7 3 - Point High Kit
2153 SD9 Horizon Sliding Door Lock
CODE DESCRIPTION
2265 - BL Servery Lock, Keyed
2266 - BL Servery Lock, Keyless
2290 Whitco Keyed Sliding Push Lock - K/N 32381
2145 Sliding Push Lock, “CYL4” Cylinder
2298 Double Cylinder Deadbolt
2392 Sliding Door Outer Pool
Miscellaneous
CODE DESCRIPTION
2450
Anthony Innovations: “Auz-t”
Security Door Roller
2451 Heavy Duty Oset Roller-30kg
2862 Security Door Top Guide to Suit 23.5mm
2863 Security Door Top Guide To Suit 21.2mm
2685
Security Door Corner Gyide Nylon
(Suit DF001/003/006, PTD001)
2686 10mm Guide Button For Servery Track
Rollers and Guides
CODE DESCRIPTION
2150
Whitco Leichhardt Sliding Door Lock
No Cylinder
2150 - 3ST
Whitco Leichhardt Standard Triple Lock Kit
Lock
Height 1050 to 1150mm
2150 - 3RV
Whitco Leichhardt Reverse Triple Lock Kit Lock
Height 950 to 1050mm
2165 Leichhardt 2 Point Lock - No Cylinder
Cylinders
Sliding Door Closers
* Please check local branch for availability
CODE DESCRIPTION
2360 “Easy Close” Sliding Door Closer
2380 “Inventco Water” Sliding Door Closer
2375 Anthony Innovations Soft Door Closer
DARLEY SCREENGUARD STAINLESS STEEL MESH SECURITY SYSTEM
14
Fabrication Guidance
Extra Instructional Resources
2910 Security Door Lock Punch 2910 & 2916 Air Operated Stake Punch vs 2920 Hand Air
Tool:
https://www.youtube.com/watch?v=d0jfeNGhsd0&t
or search: “Fabricating a Screenguard Security Door in less than 16 minutes!”
2910 Security Door Lock Punch Demonstration
https://www.youtube.com/watch?v=Awd8TwKsz9Q
or search: “2910 Security Door Punch Operation Demo”
DARLEY SCREENGUARD STAINLESS STEEL MESH SECURITY SYSTEM
15
Warranty & Maintenance
Warranty
Care & Maintenance
Screenguard product warranty is for 10 years from the date of product installation.
This warranty is to the original purchaser providing always that the product care
and maintenance recommendations have been complied with during that
period. Screenguard warrants its product to be free from defects in materials and
manufacturing when fabricated in accordance with the Screenguard fabricator
instructions. This warranty does not apply to damage caused by abuse, re, accident,
acts of god or alteration to the original product in any part
Your Screenguard Security System will require regular maintenance to remove
contaminants caused by pollution, industry, salt and climatic conditions. It is
recommended to use a soft bristled brush or non-abrasive cloth with warm potable
water and neutral detergent, then rinse with potable water. Abrasive cleaners and
harsh detergents are not recommended as these can scratch or damage the surface
area. The following table indicates the suggested frequency of maintenance.
Environment Denition Frequency
Mild 10km from coastal/rural or suburban areas Every 6 months
Moderate 5km from coastal/high trac areas Every 3 months
Severe / Coastal 1km from coastal/marine/heavy industrial Every 2 weeks
Screenguard Powawash
Regular maintenance with ScreenGuard Powawash is
required to comply with your Screenguard 10 year
warranty.
Mix 3 caps (25mL) per litre of water. It is
recommended to use a soft bristled brush or
non-abrasive cloth, then rinse with water.
Screenguard Powawash is:
Non - Toxic
Biodegradable
User-Friendly
Environmentally Friendly
200ml per bottle
DARLEY SCREENGUARD STAINLESS STEEL MESH SECURITY SYSTEM
16
Corner Stake Punch – Model HP-160-06K
The process of locking Corner Stakes into security door corners has always been a labour intensive problem.
(Most manufacturers drill the frames and then use pop rivets to secure the corners.)
The use of Reinforced Plastic Corner Stakes has changed the industry - less time consuming - easier to assemble.
The Universal Hole punch is designed to provide an easy and safe solution to enable the screw holes to be
accurately punched in each frame end in about 1 second. Result - a neat clean joint without distortion.
What you get:
Each kit contains the portable Hole Punch , Foot Valve and the necessary tube and fittings.
Specifications:
The machine is designed to crimp the corners of Security Window Frames to the Aluminium Corner Stakes.
The accepted range for frame thickness is 8-12 mm.
(Important - The corner stake thickness should be a tight fit - less than 0.2 mm clearance.
The operating pressure is a minimum of 7 bar.
Installation Instructions:
1. Place the corner press onto the bench or wall location.
2. Connect the tubing between the press and the foot valve.
3. Connect the air supply to the foot valve and you are ready to go.
Operating Instructions:
1. Slide the mitred end of the soor section into the press – fully in against the stop
2. Press the foot pedal to crimp the corner.
3. Release the foot pedal and remove the frame.
Follow the above procedure for each frame end.
Universal Fluid Power Pty Ltd
A C N 42 050 407 415 +61 7 3202 9000
P O Box 1440, Kenmore, QLD 4069, Australia
info@univer.com.au
Issue date 28/10/2019
Corner Stake Punch - 2916
The process of locking corner stakes into security door corners has always been a labour
intensive problem. Most manufacturers drill the frames and then use pop rivets to secure the
corners.
The use of Reinforced Plastic Corner Stakes has changed the industry - less time consuming -
easier to assemble.
The Universal Holy punch is designed to provide an easy and safe solution to enable the
screw holes to be accurately punched in each frame and end in about 1 second.
What You Get:
Each kit contains the portable Hole Punch, Foot Valve and the neccessary tube and ttings.
The operating pressure is a minimum of 7 bar.
Installation Instructions:
1. Place the corner press onto the bench or wall location.
2. Connect the tubing between the press and the foot valve.
3. Connect the air supply to the foot valve.
Operating Instructions:
1. Slide the mitred end of the door section into the press - fully in against the stop.
2. Press the foot pedal to crimp the corner.
3. Release the foot pedal and remove the frame.
Follow the above procedure for each frame end
Use and maintenance manual
Reproduction or translation of any part of this handbook without the prior written authorisation of the owner is
prohibited. The information and the illustrations contained in this manual are purely indicative. COMALL
INTERNATIONAL s.r.l. reserves the right to modify the product without prior notice.
Code
MUX12216_GB
REV. 04
©
DARLEY SCREENGUARD STAINLESS STEEL MESH SECURITY SYSTEM
18
Code ZOX14861
Use and maintenance manual Page 5 of 24
Warnings and symbols used:
Read this manual carefully, especially the safety warnings, before using the machine. Keep it
in a suitable place and keep it intact.
If assistance is needed contact our company only.
CAUTION: draws attention to situations and problems connected with correct machine
operation.
DANGER: draws attention to situations and problems that may compromise personal safety.
OPERATOR: we mean the person who received an adequate training before of the use of the punching
machine.
QUALIFIED PERSONNEL: refers to personnel whose profession it is to work on plant, such as for example,
electricians, plumbing and heating engineers, etc. or trained maintenance
technicians appointed by the user.
AUTHORISED PERSONNEL: refers to personnel provided by Comall to carry out replacement, modification
sed sa enihcam eht no ecnanetniam yranidroartxe ro cribed in this manual.
W
ARRANTY
The manufacturer guarantees that the punching machine supplied has been tested with positive results. The
Warranty lasts for 12 months and is limited to the good quality of materials and the absence of constructional
defects. The client has the right to replacement of any defective parts only, excluding the cost of carriage,
packing and any labour for replacing parts. The warranty therefore does not cover damage due to dropping,
tampering with or incorrect operati
on of the punching machine, failure to observe the maintenance rules
stated in the use and maintenance manual, as well as incorrect actions by the operator, so as the use of
“COMALL” spare parts not original. Moreover the spare parts not original can cause a structural collapse with
consequent risk of accidents and serious injuries. No compensation shall be given for any periods during
which the punching machine remains inactive. The warranty is conditional
upon the terms of payment having
been satisfied. Charges for the assistance provided, together with the cost of spare parts used that do not
fall within the clauses of the warranty, shall be payable directly to the technician carrying out the work, who
will issue a service receipt to be followed by a proper invoice. The hourly rates for work carried out and the
cost of spare parts used will be in accordance with the current price list.
DARLEY SCREENGUARD STAINLESS STEEL MESH SECURITY SYSTEM
19
Code ZOX14861
Use and maintenance manual Page 7 of 24
T
T
E
E
C
H
H
N
I
I
C
A
A
L
L
D
D
T
T
A
A
2.1 Technical characteristics
Description Unit of
measurement
Value
090Ø mm rednilyC
2 srebmahc fo rebmuN
5,9 mm ekorts rednilyC
4 raB erusserp gnikrow muminiM
024 .gK ecrof gnihcnuP
Air consumption Nl per cycle 0,13
Dimensions mm 409X173,5 H235
6,5 .gK thgieW
NOISE EMISSION OF THE PUNCHING MACHINE
NOISE VALUES ACCORDING TO ISO 3746
)Bd2-/+( 1,501 : ) A ( Bd level rewop dnuoS awL
Lpa Sound pressure level at operator station dB ( A ) : 98,6 (+/-2dB)
Use personal protective equipment complying with current legislation.
2.2 Components and connections
No. Description
1. Punching machine
2. Profile support
3. Profile support
DARLEY SCREENGUARD STAINLESS STEEL MESH SECURITY SYSTEM
20
Code ZOX14861
Use and maintenance manual Page 8 of 24
3
3
I
I
N
N
S
S
T
T
A
A
L
L
L
L
A
A
T
T
I
I
O
O
N
N
3.1 Installation
Before installing the punching machine, check for any visible damage. If there is any, do not
install the punching machine and do not use it, but contact COMALL service assistance.
Check that the package contains all the components listed in the previous chapter. If any parts
are missing contact COMALL service assistance.
The punching machine must be installed by qualified personnel, placing the bench on a flat,
solid surface (cement or similar).
3.1.1 Preparing the machine
Remove the packaging from the machine and
dispose of it conforming to current legislation.
3.1.2 Compressed air connection
PRELIMINARY OPERATION
To put the machine into service, check that the factory compressed air supply is equipped
with hoses of suitable diameter for the flow required and a stop cock (valve) before the
punching machine. Do not connect up the punching machine at a distance greater than 3
metres from the compressed air supply. Do not connect up the punching machine to the
air supply without a pressure switch, pressure regulator, gauge, and condensation drain.
IT IS OBLIGA
TORY TO MAKE SURE THE CONNECTIONS ARE CORRECT BEFORE
SUPPLYING THE MACHINE WITH POWER.
CAUTION
Before introducing air into the punching machine circuit, check the oil level in the intake
filter through the glass; if necessary, top up by undoing the relative reservoir.
Check that the air supply is the same as what is stated in the “technical specifications”
table.
Connect the air supply directly to the
control on the punching machine or to
the filter unit according to the layout
shown in the figure.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30

DARLEY 2920 Technical Manual

Type
Technical Manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI