LPS3AC

Altronix LPS3AC Installation Instructions Manual

  • Hello! I am an AI chatbot trained to assist you with the Altronix LPS3AC Installation Instructions Manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Overview:
LPS3AC linear power supply/charger converts a low voltage AC input to a 12VDC/24VDC output. This power supply is
specifically designed to provide the power needed by the most demanding security and access control applications.
Specifications:
Input:
• 16VACor28VAC(refer to Voltage Output/Transformer Selection Chart).
Output:
• 12VDC/24VDCselectableoutput.
• 2.5ampcontinuoussupplycurrent.
• Filteredandelectronicallyregulatedoutput.
• Thermaloverloadandshortcircuitprotection.
Battery Backup:
• Built-inchargerforsealedleadacidorgeltypebatteries.
• Maximumchargecurrent500mA.
• Automaticswitchovertostand-bybattery.
• Fusedbatteryprotection(circuitbreakeravailable).
• Includesbatteryleads.
Supervision:
• ProvidesACFailsupervision(Form“C”contacts).
Visual Indicators:
• ACinputandDCoutputLEDindicators.
Board Dimensions (W x L x H approximate):
4”x7”x2”(101.6mmx177.8mmx50.8mm).
Specifiedat25˚Cambient.
Voltage Output/Transformer Selection Table:
Output
Voltage
Switch
Position
Transformer Requirements
(Recommended Altronix Part #’s)
12VDC Closed 16VAC/56VA(T1656).
24VDC Open
24VACor28VAC/100VA
(AltronixmodelT2428100)
Note: Transformers with higher VA ratings may be used.
Installation Instructions:
TheLPS3ACshouldbeinstalledinaccordancewithTheNationalElectricalCodeandallapplicableLocalRegulations.
1. MountLPS3ACinthedesiredlocation/enclosure.
2. Set DC output voltage using switch SW2 (Fig. 1) (refer to Voltage Output/Transformer Selection Chart).
3. ConnectpropertransformertotheterminalsmarkedAC(refer to Voltage Output/Transformer Selection Chart).
4. Measureoutputvoltagebeforeconnectingdevices.Thishelpsavoidingpotentialdamage.
5. Connectdevicestobepoweredtotheterminalsmarked[----DC+].
6. Whentheuseofstand-bybatteriesisdesired,theymustbeleadacidorgeltype.
Connectbatterytotheterminalsmarked[+BAT---]ontheunit(batteryleadsincluded).
Usetwo(2)12VDCbatteriesconnectedinseriesfor24VDCoperation.
7. Whenbatteriesarenotused,alossofACwillresultinthelossofoutputvoltage.
8. Connectsupervisorytroublereportingdevicestotheoutputsmarked[ACFail].
LPS3AC - Linear Power Supply/Charger
OPEN SWITCH
CLOSED SWITCH
Switch Detail
AC
DC
AC
AC FAIL
CONTACTS
AC
-- DC +
-- BAT +
NC C NO
SW1
12V-CLOSED
24V-OPEN
SW2
12V-CLOSED
24V-OPEN
Fig. 1
LED Diagnostics:
Red (DC) Green (AC) Power Supply Status
ON ON Normal operating condition.
ON OFF LossofAC.Stand-bybatterysupplyingpower.
OFF ON No DC output. Short circuit or thermal overload condition or defective unit.
OFF OFF No DC output. Loss of AC. Discharged or no battery present.
Terminal Identification:
Terminal Legend Function/Description
AC/AC Low voltage AC input (refer to Voltage Output/Transformer Selection Chart).
For12VDCoutputuse16VACwith56VApowerratingorhigher.
For24VDCoutputuse28VACwith85VApowerratingorhigher.
---DC+ 12VDC-24VDC@2.5ampcontinuousoutput.
---BAT+ Stand-bybatteryconnections.Maximumchargerate500mA.
ACFAIL
N.C.,C,N.O.
UsedtoreportlossofAC(e.g.connecttoaudibledeviceoralarmpanel).Relaynormally
energizedwhenACpowerispresent.Contactrating1amp@120VAC/28VDC.
Altronixisnotresponsibleforanytypographicalerrors.Productspecificationsaresubjecttochangewithoutnotice.
14058thStreet,Brooklyn,NewYork11220USA,718-567-8181,fax:718-567-9056
website:www.altronix.com,e-mail:[email protected],LifetimeWarranty,MadeinU.S.A.
IILPS3AC-Rev.112204 D24M
MEMBER
AC
DC
AC
AC FAIL
CONTACTS
AC
-- DC +
-- BAT +
NC C NO
SW1
12V-CLOSED
24V-OPEN
SW2
12V-CLOSED
24V-OPEN
/