Simplicity 50" TURBO BLOWER ASSEMBLY, 44" TURBO BLOWER KIT, 38" TURBO BLOWER KIT User manual
- Type
- User manual
OPERATOR’S
MANUAL
Turbo Blower
For
LT/1600
Series Lawn Tractors
and GT/1700 Series Garden Tractors
38” Blower Assy., Mfg. No. 1691867
~44”
Blower Assy., Mfg. No. 1691868
60”
Blower Assy., Mfg. No. 1692030
FORM 170548906
PRINTED IN U.S.A.
CCI
I
HEX CAPSCREW
CARRIAGE BOLT
II
PLAIN WASHER
1
LOCKWASHER
1
NUT
HEX
CAPSCREW
IDENTlFlCATlON
Shown below are actual size heads for standard screw sizes.
Example: a
114
screw has 7/16 head and thus requires a 7/16
wrench. To measure length, use the scale below.
(--Jo000
3/4”
Head
s/s”
Head 9/i
6” Heed
i/2” Head
7116”
Head
screw
with
screw
w’%h screw with
screw
with screw with
l/Y
SD.
7/l
6”
S.D.
3lV SD.
5116"
S.D. l/4”
SD.
WASHER AND NUT IDENTIFICATION
Place the washer or nut on the above scale to
determine the inside diameter. The actual inside
diameter can vary
l/16
inch. Use the scale for
comparison.
STANDARD
FASTENER
IDENTIFICATION
CHART
Hardware sizes given in the
illustrations throughout this
manual.
If a washer or nut is identified as
“washer, l/2” or “nut, l/2”, this
means the inside diameter is
l/2
inch
If a screw is identified as “screw,
l/2
x
2”,
this means the shaft
diameter is
l/2
inch and the
shaft of the screw is 2 inches
long. If a screw is identified as
“screw,
l/2
-
16 x
2”,
the number
“16” means that the screw has
16 threads per inch.
SAMPLE: SCREW IDENTIFICATION
SAMPLE: NUT IDENTlFlCATlON
Nut,
II2
Inside
Diameter
44” Turbo Blower
-
Kit Parts
Blower
Pulley
Fixed
Idler
Pulley
Tensioning
Idler Pulley Arbor
Pulley
NOTE Replacement roller (?‘) is provided
because mower deck end roller
may.w’=zir
faster
when
turbo
blower is used.
Figure 1.
.$,
Ret.
Description
A.
Turbo Blower Assy.
0.
Deflector Rod Support
C.
Capscrew, Truss Hd., 10-24 x
3/4
D.
Nut. Nvloc. 20.24
Plv&
&a&t
Carrfaae Bolt.
M
6-l 5 x
314
Screw;Whiz
Lo&, 5/1618x l/2
Baffle
Amy.
Idler
Pulley
Assy.
Capscrew, 5lf
615
x 7/S
Lo&washer
Nut, Nyloc, 511618
Belt Stop
9
1
4
4
1
1
1
1
1
2
1
2
1
Ref.
Description
N. Support Brace
Assy.
0.
Belt Cover
P.
Pulley, Double Groove
Q. Capscrew,
711614 x
2
R. Washer.
5116
S. Spacer’
Capscrew,5/15-18x1-112
L:
Locknut, Flange
V. Stud, 611618
x61/2
F
Washer, 5/16 I.D., 7/S
0.D.
Washer, 5/16 I.D., 1” O.D.
7
u: Roller, Replacement
3
:
1
2
1
1
3
1
2
2
1
-
44” Turbo Blower
-
Assembly
1. Remove the mower deck from the tractor.
2. Remove the deflector from deck and retain
hardware for reinstallation. Remove and discard
plastic plug from housing.
3. Install baffle assembly (A, figure 2) with U-bracket,
spacer, 5/16-18 x
l-1/4
carriage bolt, 5/16
lockwasher and 5/l 6 nut. Reuse 1/4-20x
314
car-
nage bolt, flat washer, lo&washer and nut (from
deflector mounting removed earlier) at rear tab on
baffteassembty.OnLT/16OOSeriestractors,remove
arbor cover and up stop. Retain flat washer and
upstop.
Arbor cover and taptiie screws will not be
reused.
4. Remove the mower belt and right-hand
(discharge) pulley. Retain large flat washer and
lockwasher.
5. Remove the existing 3/4” taptite screws and
install two 5/16-18~7/8”capscrews (A,figure3)
through arbors.
6,
Position pulley bracket assembly (A, figure 4)
on 7/8” capscrews. Secure with two 5/16-18
whizlock nuts (B).
7. Install new double-groove pulley
(C)
to arbor.
Secure with large washer, lockwasher and new
7/16-14 x 2” capscrew (D, figure 4). Reinstall
arbor drive belt to bottom groove. Block the
mower blade with wood and torque capscrew to
50-70 ft.
Ibs.
(68-76 Nm).
NOTE
It may be easier to install drive belt around
double groove pulley with belt removed from
spring-loaded idler pulley. Then pull against
spring-loaded idler and reinstall belt to idler
pulley.
8
Position tab up
Figure 2.
A. Baffle
B. Bracket
c. spacer
D. Carn’age Bolt
E. Lcdwasher
F. Nut
Figure 3.
A.
Capscrews,
511618
x
7/B”
Figure 4.
A. Pulley Bracket Assembly C. Double-Groove Pulley
B. Whizlock Nuts D.
capscrew,
7116-14
x
2
10. Install the new deflector support rod (A, figure
5) underneath pivot bracket (B) and install
bracket to deck. Secure bracket with two
5/16-
18 x
3/4
carriage bolts (C, from underneath) and
two flange locknuts.
Figure 5.
A
. Deflector Support
Rod
B. Pivot Bracket
C. Carriage Bolt, S/16 x 314
11. Turn deflector over and locate the drillpoints
(refer to figure 6). Drill four
13/64”
holes. Install
deflector (A, figure7) tonewsupportandsecure
with four 10-24 x
3/4
trusshead screws
(8,
from
underneath) and four
nyloc
nuts
(C).
Figure 6.
“2138
Figure 7.
A.
Deflector
B.
Trusshead
Screw, 10-24x
314
C.
Nyloc
Nuts
5
12. Install support brace assembly (A, figure 8) to
rear surface of deck. Secure with two 5/16-18x
l/2
taptite screws (B).
13. Adjust spring latch (A, figure 9) to overlap (by
l/4”
- 3/16”) over top edge of deflector (B) in
down position. Spring latch should hold
deflector down, but deflector should be able to
be rotated up by hand. Tighten
capscrew
(C)
securely after adjustment.
14. Install mower deck to tractor.
15. To install turbo:
a. Install spindle (A) of turbo housing (B) into
pivot bracket (C).
b. With right hand, hold both strands of belt
around turbo idler pulley (E).
c. Pull belt loop and belt tension arm (D) fully
forward.
d. Lift deflector to maximum raised position.
e. Rotate turbo into position, making sure it fits
securely over wingnut assembly. Make sure
belt is clear of all brackets.
f. Put belt between belt stop and top of arbor
pulley.
g. Put belt in lower groove of pulley first and
then around fixed idler pulley (G).
h. Release belt tension arm.
i. Check to be sure belt is routed around all
pulleys correctly.
16. With turbo housing in position, tighten wingnut
(E, figure 10). Put mower drive belt into top
groove of double pulley and on engine PTO
pulley.
Figure 8.
A. Support Brace Assembly
B. Taptite Screws
C. Wingnut
Figure 9.
A. Spring
Latch
B. Deflector Edge c.
capscrew
Figure 10. D. Belt Tension Arm
A. Spindle E. Wing Nut
B. Turbo Housing F. Turbo Idler Pulley
C. Pivot Bracket G. Fixed Idler Pulley
6
38” Turbo Blower
-
Kit Parts
Blower
Pulley
/
‘2138
Fixed
Tensioning
Idler Pulley
\
Arbor
Pulley
:igure
1. Kit Parts NOTE: Replacement roller (0) is provided because mower
deck end m//er may
wear
faster when
turbo
blower is used.
Turbo Blower
Assy.
Deflector Rod Support
Capscrew, Truss Hd., to-24 x
314
Nut,
Nyloc,
20-24
Pivot Bracket
Carrlage Bolt, 5/18-l 8 x
314
Locknut, Flange, S/18-18
Baffle Aesy.
Idler Pulley Aeey.
ury.
izer.
Description
:J.
Screw, Taptite, S/W-18
x
l-l/2
K. Lo&washer
4L Nut,
5/1618
4M.
BeltStop
1
N. Support Brace Aeey.
f
0.
Screw, Taptiie,
51%18
x
Ii2
1
:
Pulley, Double Groove
Roller, Replacement*
1
Y
2
2
1
1
2
1
1
3
38” Turbo Blower
-
Assembly
1. Remove the mower deck from the tractor.
2. Remove the deflector from deck and retain
hardware for reinstallation. Remove and discard
plastic plugs (2) from housing.
3. Install baffle assembly (A, figure 2) with U-
bracket (B), spacer (C), 5/16-18 x l-1/4”
carriage bolt (D), lockwasher (E) and nut (F) at
stone guard. Reuse existing l/4-20 x 3/4”
carriage bolt, flatwasher, lockwasher and nut
from deflector mounting to secure rear tab on
baffle assembly. Tighten hardware securely.
4. Remove the existing belt stop and hardware
from mower deck and retain small flat washers.
Large washers
(l-1/2”
O.D.) will not be reused.
Note that the two existing 3/4” long taptite
screws located underneath the belt stop will be
replaced in the next step. Belt stop will not be
reused.
5. Remove the mower belt (from right hand pulley
only) and right-hand (discharge) pulley. Retain
hardware for reinstallation. Pulley will not be
reused.
6. Remove the existing 3/4” taptite screws and
install 5/16-18x l-1/2” taptite screws (A, figure
3) through arbors.
7.~
Position pulley bracket assembly (A, figure 4)
on l-1/2” taptite screws. Retaining hardware
will be installed in step 9.
8. Install double-groove pulley (B, figure 4) to
arbor and reinstall capscrew, lockwasher, and
large flat washer to secure pulley. Torque
capscrew
to 50-70 ft. Ibs. (68-76 Nm). Do not
install mower drive belt on pulley groove.
9. Install new belt stop (C) on top of pulley bracket
assembly (short leg towards front). Reuse flat
washer, lockwasher and nut. (New lockwasher
and nut are provided.) Tighten hardware
securely.
2147
Position tab up
&
I
m
as shown.
Figure 3.
A. Taptite Screws
L(/
, towards-front \\
Figure 4.
A. Pulley Bracket Assembly
B. Double-Groove Pulley
C. Belt Stop
4
Table of Contents
STANDARD FASTENERS ............................................................................................... Inside Front Cover
SAFETY DECALS ..........................................................................................................................................
1
SAFETY RULES ............................................................................................................................................ 2
38” TURBO BLOWER
Kits Parts ............................................................................................................................................. 3
Assembly ............................................................................................................................................. 4
44” TURBO BLOWER
Kit Parts ............................................................................................................................................... 7
Assembly ............................................................................................................................................. 8
50” TURBO BLOWER
Kit Parts ............................................
..“.
............................................................................................
12
Assembly ........................................................................................................................................... 13
OPERATION ...................................................................................................................... Inside Rear Cover
Safety Decals
/
A DANGER
/
00NOTOPERATEMOWER
~'
WITHOUTDEFLECTOR
ORENTIREGRASS
CATCHERIN PLACE.
/
A DANGER
ROTATINGBLADES
SHUT OFF MOWER
ANOTRACTOR
BEFORE SERVICING
ORCLEANINGBLOWER
AND MOWER.
1
Safety Rules
a
Read these safety rules and the safety rules in your Operator’s
Manual and follow them closely. Failure to obey these rules
could result in loss of control of vehicle, severe personal injury
to yourself, or damage to property or equipment. The triangle
A
in the
text signifies important cautions or waminas which must be followed.
A
WARNING
When blower assembly is removed from mower deck, the deflector must be
properly installed.
1.
Know the tractor controls and how to stop
quickly. READ THE OWNER’S MANUAL.
2. Disengage the PTO, shut the engine off
and wait for all moving parts to stop before
attaching, adjusting, or disconnecting any
part of the collection system.
3.
Check the collection system to make sure
it is bolted tightly to tractor.
4. Check the latch handle to make sure it is
engaged so the dump cart’s box is locked
to the frame.
5.
Look behind to make sure the area is clear
before backing up.
6.
DO NOT turn sharply when the tractor or
rider is alongside a building or any object.
7.
DO NOT carry passengers in the cart.
8.
ACAUTION:
For added tractor stability
and to prevent tipping or loss of control;
a.
Use reduced speed on uneven ground
and when turning corners.
b. Reduce loads on hillsides. It is rec-
ommended that the collection system
be kept only half full when negotiating
any slopes. Start mowing on slopes
when the collection system is empty.
c.
Mow up and down the face of slopes;
never across the face of any slope.
9.
A
WARNING: When operating on
slopes, use front counterweight. Never
operate on slopes greater than 30%
(16.7’).
IO.
ACAUTION:
Objects may be thrown
from mower.
For your safety:
a. DO NOT remove the cover while the
mower blades are turning. Shut off the
engine before opening the door or
removing the grass chute.
b. Be sure the complete collection
system is in place (cover secure and
grass chute connected) before
operating the mower.
c. DO check the twin bag cover fre-
quently for wear and tear. Replace with
new cover for safety protection.
11. For best results when mowing grass: Set
the mower to cut from 1 to 2 inches of
grass. If grass isexceptionallytall,setyour
mower as high as possible for first cutting.
Lower cutting height at succeeding
cuttings until proper height is reached. It
may be necessary to mow tall grass at a
slower tractor speed.
2
10.
lnstallhvolargeflatwashers
(A,
1”
O.D.,
Wthick)
and long
stud
(B). Do not overtighten stud. Install
5/16
washer
(F)
on stud. Install
beit
cover (C).
Securewfth5/16washer(D) and
5/16nylocnut(Q.
(Torque nutto provide slight resistance when cover
is rotated on stud.)
11. Remove two
5/16-18
x
1”taptitescrews (and flat
washer from top location) securing mower
support/height indicator to housing. Discard
indicator and washer. Install support brace
assembly (A, figure 9) against mower roller
support with existing taptite screws (B).
12. Attach and adjust spring latch (C) tooverlap (by
114”
-
306”) over top edge of deflector (D) in
down position. Spring latch should hold
deflector down, but deflector should be able to
be rotated up by hand.
15
A-Flat Washer D. Washer
B.
Stud E. Nut
c. BeIt Cover F. Washer
Spring latch
should retain
deflector
Figure 9.
A. Support Brace Assembly
B. Taptite Screws C. Spring Latch
D. Deflector
~.,
::
:
..-.
13. Install mower deck to tractor.
14. To install turbo:
a. Make sure cover (F, figure 10) is rotated all
the way forward.
b. Install spindle (A) of turbo housing (B) into
pivot bracket (C).
c. With right hand, hold both strands of belt
around turbo idler pulley (E).
d. Pull belt loop and belt tension arm (D) fully
forward.
e.
Lift deflector to maximum raised position.
f. Rotate turbo into position, making sure
itfits
securely over wingnut assembly. Make sure
belt is clear of all brackets.
g.
Put belt in upper groove of pulley first and
then around fixed idler pulley (G).
h. Release belt tension arm.
i. Check to be sure belt is routed around all
pulleys correctly.
15. Remove front
5/l
6
x
3/4”
taptlte
screw (B, figure 11)
fastening strap (A) to housing at right hand lii roller.
Reinstall capscrew (B) with
beR
stop (C). Position
belt
stop l/16” away from back of bait (approxi-
mately parallel to
fii
roller).
16. lighten wing nut attop of suppost brace assembly.
17. Rotate belt cover(D) rearward onto latch (E). (If latch
does not
fft
into cover slot when rear edge of cover
is in line with arm assembly, adjust position by
rotating latch.) Makesurethat pulleycapscrew
(F)
is
tightened securely.
Figure 10.
A. Spindle
B. Turbo Housing
C. Pivot Bracket
D. Belt Tension Arm
E. Turbo Idler Pulley
F. Belt.Cover
G. Fixed Idler Pulley
Figure
11.
A
Strap
8.
Capscrew
c.
B&stop
D. Belt Cover
E Latch
F.
Capscrew
50”
Turbo Blower
-
Assembly
1. Remove the mower deck from the tractor.
2. Remove the deflector from deck and retain
hardware for reinstallation. Remove and discard
plastic plug from housing.
3. install baffle assembly (A, figure 2)
wtth
U-bracket,
spacer, 5/16-18 x
l-1/4
carriage bolt, 5/16
lockwasher and
5/l
6 nut. Reuse
1/4-20x
3/4 car-
riage
bolt,
flat washer, lockwasher and nut (from
deflector mounting removed earlier) at rear tab on
baffle assembly. Remove arbor cover.
4. Remove the mower belt and right-hand
(discharge) pulley. Retain large flat washer and
lockwasher.
5. Remove the existing 3/4” taptite screws and
installtwo5/16-l8x7/8”capscrews(A,figure3)
through arbors.
6. Position pulley bracket assembly (A, figure 4)
on
7/E”
capscrews. Secure with two 5/16-18
whizlock
nuts (B).
::::.
.A:.:.:.
:::.
7. Install new double-groove pulley (C) to arbor.
Secure with large washer, lockwasher and new
7/16-14
x
2”
capscrew
(D, figure 4). Reinstall
arbor drive belt to bottom groove. Block the
mower blade with wood and torquecapscrew to
50-70 ft. Ibs. (68-76 Nm).
NOTE
It may be easier to install drive belt around
double groove pulley with belt removed from
spring-loaded idler pulley. Then pull against
spring-loaded idler and reinstall belt to idler
pulley.
13
‘2147
Figure 2.
A.
Baffle
6.
Bracket
c. spacer
0. carriage Bolt
E. Lockwasher
F. Nut
Figure 3.
Figure 4.
A. Pulley Bracket Assembly C. Double-Groove Pulley
B. Whizlock Nuts D.
Capscrew,
7116-14
x
2
-;
..~,
.,
~.~.
.I
:.
..:.
_
:::
8. Install new deflector support rod (A, figure 5) un-
derneath pivot bracket (6) and install bracket to
deck. Secure bracket and deflector support rod with
two
5/l
6-l 8 x 3/4” carriage bolts (C, from under-
neath) and flange locknuts (D).
Figure 5.
A
Deflector Support Rod c. carriage
8011,
5/16
x
34”
B. Pivot Bracket D. Flange Locknut
9. Turn deflector over and locate the drillpoints
(refer to figure 6). Drill four 13/84” holes. Install
deflector (A, figure7) to new support and secure
with four
10-24x
3/4
trusshead screws (B, from
underneath) and four nyloc nuts (C).
Figure 6.
Figure 7.
A
Deflector
B. Trusshead Screw,
10-24
x
314
C. Nyloc Nuts
14,
13. Install mower deck to tractor.
14. To install turbo:
a. Make sure cover (F, figure 10) is rotated all
the way forward.
b. Install spindle (A) of turbo housing (B) into
pivot bracket (C).
c. With right hand, hold both strands of belt
around turbo idler pulley (E).
d. Pull belt loop and belt tension arm (D) fully
forward.
e.
Lift deflector to maximum raised position.
f.
Rotate turbo into position, making sure it fits
securely over wingnut assembly. Make sure
belt is clear of all brackets.
g.
Put belt in upper groove of pulley first and
then around fixed idler pulley (G).
h. Release belt tension arm.
i.
Check to be sure belt is routed around all
pulleys correctly.
15. Remove rear
5/16
x
3/4”
taptite screw fastening
strap
(8,
figure 11) to housing at right hand lift
roller. Discard screw. Install 5/16-18
x
i-1/2
capscrew
(A), lockwasher, flat washer (E, top)
belt stop(D), flatwasher (E, bottom), and spacer
(C).
Position belt stop
l/16”
away from back of
belt.
16. Tighten wing nut at top of support brace
assembly.
17. Rotate belt cover (F, figure 11) rearward onto
latch (G). (If latch does not fit into cover slot
when rear edge of cover is in line with arm
assembly, adjust position by rotating latch).
Make sure that pulley capscrew (H) is tightened
securely.
11
Figure 10.
A. Spindle
B. Turbo Housing
C. Pivot Bracket
D. Belt Tension Arm
E. Turbo Idler Pulley
F. Belt Cover
G. Fixed Idler Pulley
Slot in belt cover
to fit squarely over
L
Figure 11.
a
capscrew
B. Strap
C. Spacer
D. Belt Stop
E. Washer
F. Belt Cover
G. Latch
H. Pulley
Capscrew
Safety
Decal
Figure 1.
t
Ret. Description
A. Turbo Blower Assy.
B. Deflector Rod Support
C.
CapsCW%‘,
Truss Hd., lo-24 x 3/4
D.
Nut,
Nyloc,
2024
E.
Pivot Bracket
F.
Carriage Bolt, 5/16-16x 3/4
G. Washer,
5116
I.D., 7/s O.D.
H. Baffle Assy.
::
Idler Pulley
Ass+
Capscrew,
S/16-16
x
7i6
9
Ref.
Descrlptlon
K
Washer,
5116
I.D., 1” O.D.
Y
,:
k
Nut, Belt
Nyk,
5/16-l
0
Stop
1 1
4
N. Support Brace
Assy.
1
1
0.
Belt Cover
1
2
2
::
Pulley, Double Groove
1
Capscrew, 7lt 6-i 4 x2
1
1
R. Locknut, Flange
3
:
S.
Stud,5/1616xCl/Z
1
T.
Roller, Replacement
1
12
.~.,.
:
:‘.A
~‘:
..‘...~.
8. Install new deflector support rod (A, figure 5)
underneath pivot bracket(B) and install bracket
to deck. Secure bracket and deflector support
rod with 5/16-18
x
3/4” carriage bolt (C, from
underneath) and flange locknut (D) in front
hole. Use 5/16-18
x
l/Z”
whizlock
screw (E) in
rear hole.
9. Turn deflector over and locate the drillpoints
(refer to figure 6). Drill four
13/64”
holes. Install
deflector
(A,figure7)
tonewsupportandsecure
with four
10-24x
3/4
trusshead screws (B, from
underneath) and four
nyloc
nuts (C).
Figure 5.
A. Deflector
Support
Rod
D. Flange Locknut
6.
Pivot Bracket E. Whizlock Screw,
C. Carriage Bolt, 5/16x 3/4”
5116-16
x
l/2”
Drill four
13/W’
holes
Figure 6.
Figure 7.
A. Deflector
6.
Trusshead
Screw, IO-24
x
3f4
C. Nyloc Nub
9
IO. On
LT/I
600 Series tractors, reinstall upstop using
existing taptlle screw (A; figure 8) and flat washer
at left hand leg. Use existing flat washer and long
stud
(8)
at right hand
leg.
On GT/1700
Series
tractors, use two large flat washers (1” O.D.,
l/8”
thick) and long stud (B). Do not overtighten taptite
screw or stud. Install 5/16 washer
(F)
on stud.
Install
beit
cover (C). Secure with
5/i
6 washer (D)
and5/16
nylocnut (E). (Torquenuttoprovideslight
resistance when cover is rotated on stud.)
11. Removetwo5/16-18xl”taptitescrews(andflat
washer from top location) securing mower
support/height indicator to housing. Discard
indicator and washer. Install support brace
assembly (A, figure 9) against mower roller
support with existing taptite screws
(6).
12. Attach and adjust spring latch (C)to overlap (by
l/4”
- 3/16”) over top edge of deflector (D) in
down position. Spring latch should hold
deflector down, but deflector should be able to
be rotated up by hand.
Figure
8.
;
T&p;ite
Screw
cl
Belt Cover
D. Washer
E. Nut
F. Washer
Spring latch
should retain
deflector
Figure 9.
A. Support Brace Assembly
B. Taptite Screws C. Spring Latch
D. Deflector
10
Operation
For safety reasons grass and debris are to be
removed only after engine is shut off, key
removed, and all moving parts stopped.
BEFORE OPERATION
Clear the lawn of all sticks, stones, wire and other
debris which maybecaught
orthrown
bythemower
blades.
Clean the tube with mild detergent (other products
may damage tube). Inspection windows can be
removed to be cleaned. Make sure windows
are
securely in place before operating.
Check grass condition. If wet, wait until later in the
day. If grass is wet plugging may occur.
For efficient bagging, air circulation under the
mower deck, through the chute and into the bag is
very important. For this reason, you should remove
grass and debris from underside of mower deck,
discharge chute and screen inside cover.
The blower housing and tubeshould be removed for
cleaning. Remove the tube by unlatching the lower
tube clip from blower housing.
If desired, the bags can be lined with 30 gallon trash
bags for easy disposal.
Inspect the grass bags for wear or damage. Make
sure that there is a snug fit between mower deck,
blower housing, tubes, and grass bag cover.
OPERATION
Grass should be cut often, and not tooshort. If grass
is too long or lush it may be necessary to keep
ground speed to a minimum or to cut only half the
width to prevent clogging. If grass is high, operate
with mower in high cutting position. Cut
the,grass
again in lower cutting position, if desired.
To check if grass is flowing up tube, view tube
through rear inspection window. Do not open cover
with mower engaged.
To check if grass bags are full, reach back and feel
top of right bag (left bag will fill first) or view tube
discharge through front inspection window in
cover.
If a large aniount of cut grass is spilling out from
under deck, the tube may be plugged
orgrass
bags
are full. Shut off
tractor,disengage
PTO, and allow
all moving parts to stop before disconnecting tube.
Always operate with throttle at full speed.
OPERATION WITHOUT TURBO
For operation without turbo, the deflector must be
properly installed in the down position and retained
by spring latch.
OnWdecks,thearborpulleycover
must be rotated into correct operating positionover
latch.
To remove turbo, reverse steps 15
-
16 (38” mower) or
steps 14
-
17 (44’ and 50’ mower).
EYPTYl,NG
THE BAGS (Twin Bagger)
NOTE
Move the seat to the forward position and tilt up
to allow cover to remain in “up” position.
Raise the cover. If a plastic liner was not used,
unhook the bag and turn upside down to empty (use
handle on bottom).
If plastic liner was used, first tie up top of liner. Then,
either pull the liner out, or turn the bag upside down
and allow the filled liner to slide out:
STORAGE
1. Clean the grass catcher thoroughly.
2. If paint has been scratched on metal parts, coat
with paint or
oil,.
3. Store in a dry area. Hang the bags to dry. Always
store away from moisture.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
Simplicity 50" TURBO BLOWER ASSEMBLY, 44" TURBO BLOWER KIT, 38" TURBO BLOWER KIT User manual
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Simplicity 38", 44", 50" TURBO BLOWER User manual
-
Snapper TURBO COLLECTION SYSTEM User manual
-
Simplicity 1694924 User manual
-
-
-
-
-
Simplicity 1694499 User manual
-
-
Other documents
-
-
-
-
-
-
-
-
-
-