Western DRL Wire Adapter Kit #69867 Installation guide

  • Hello! I've reviewed the provided installation instructions for the Western Wire Adapter Kit 69867 and Headlamp Harness Kit 29051. This document details the process of integrating the DRL wire adapter using the 10-position connector on your vehicle's harness. I'm ready to help with any questions about the installation procedure or features outlined in this guide.
  • Where is the 10-position connector located?
    What should be done with the cavity plug from position "H"?
    Which wire should the DRL wire be spliced to?
Lit. No. 69866, Rev. 01 Printed in U.S.A. November 1, 2013
Lit. No. 69866, Rev. 01 Printed in U.S.A. November 1, 2013
4. Insert the terminal on the DRL
wire into position "H" on the
connector. The terminal lock
should face the outside edge
of the connector.
5. Replace the secondary lock on
the wire side of the connector.
6. Route the DRL wire along
the plugin harness to
the driver‑side headlamp
connectors, taping the wire to
the harness as necessary to
secure it.
7. Splice the DRL wire from the
adapter kit into the vehicle
DRL bulb POSITIVE (+) wire
following the instructions
in the Recommended
Splicing Procedure section
of the harness kit Installation
Instructions.
4. Insert the terminal on the DRL
wire into position "H" on the
connector. The terminal lock
should face the outside edge
of the connector.
5. Replace the secondary lock on
the wire side of the connector.
6. Route the DRL wire along
the plugin harness to
the driver‑side headlamp
connectors, taping the wire to
the harness as necessary to
secure it.
7. Splice the DRL wire from the
adapter kit into the vehicle
DRL bulb POSITIVE (+) wire
following the instructions
in the Recommended
Splicing Procedure section
of the harness kit Installation
Instructions.
DRL Wire Adapter Kit #69867
29051 Headlamp Harness Kit
DRL Wire Adapter Kit #69867
29051 Headlamp Harness Kit
INSTALLATION INSTRUCTIONS
1. On the harness, locate the 10position connector with
dark blue wires, on the leg marked "C".
2. Remove the secondary lock
from the wire side of the
connector.
3. Remove the cavity plug from
position "H" and discard.
INSTALLATION INSTRUCTIONS
1. On the harness, locate the 10position connector with
dark blue wires, on the leg marked "C".
2. Remove the secondary lock
from the wire side of the
connector.
3. Remove the cavity plug from
position "H" and discard.
A B
B
C
10-Positio
n
Connector
Blue Wires
Leg "C"
A B
B
C
10-Positio
n
Connector
Blue Wires
Leg "C"
D
E
B
C
A
G
F
J
H
K
Secondary
Lock
Cavity
Plug
D
E
B
C
A
G
F
J
H
K
Secondary
Lock
Cavity
Plug
A B
B
C
DR
L
Wire
Secure
to
Harness
A B
B
C
DR
L
Wire
Secure
to
Harness
D
E
B
C
A
G
F
J
H
K
Terminal
Lock
Position "H"
D
E
B
C
A
G
F
J
H
K
Terminal
Lock
Position "H"
Lit. No. 69866, Rev. 01 Printed in U.S.A. November 1, 2013
Lit. No. 69866, Rev. 01 Printed in U.S.A. November 1, 2013
A DIVISION OF DOUGLAS DYNAMICS, LLC
A DIVISION OF DOUGLAS DYNAMICS, LLC
The company reserves the right under its product improvement policy to change construction or design details and furnish equipment when so altered without
reference to illustrations or specications used. This equipment manufacturer or the vehicle manufacturer may require or recommend optional equipment
for snow removal. Do not exceed vehicle ratings with a snowplow. The company offers a limited warranty for all snowplows and accessories. See separately
printed page for this important information.
The company reserves the right under its product improvement policy to change construction or design details and furnish equipment when so altered without
reference to illustrations or specications used. This equipment manufacturer or the vehicle manufacturer may require or recommend optional equipment
for snow removal. Do not exceed vehicle ratings with a snowplow. The company offers a limited warranty for all snowplows and accessories. See separately
printed page for this important information.
/