Stelpro WF Installation guide

Stelpro
Brand
Stelpro
Model
WF
Type
Installation guide

This manual is also suitable for

Stelpro WF is a wall-mounted fan heater with a built-in thermostat that allows you to control the temperature of your room. It can be easily installed by following the instructions in the manual and is suitable for a variety of applications, including heating small rooms, bathrooms, and workshops. The fan heater has a number of features that make it a great choice for your home, including:

  • Adjustable thermostat: The built-in thermostat allows you to set the desired temperature for your room, and the fan heater will automatically turn on and off to maintain that temperature.
  • Fan-only mode: In addition to heating your room, the fan heater can also be used as a fan only, which is great for circulating air and cooling down your room on hot days.

Stelpro WF is a wall-mounted fan heater with a built-in thermostat that allows you to control the temperature of your room. It can be easily installed by following the instructions in the manual and is suitable for a variety of applications, including heating small rooms, bathrooms, and workshops. The fan heater has a number of features that make it a great choice for your home, including:

  • Adjustable thermostat: The built-in thermostat allows you to set the desired temperature for your room, and the fan heater will automatically turn on and off to maintain that temperature.
  • Fan-only mode: In addition to heating your room, the fan heater can also be used as a fan only, which is great for circulating air and cooling down your room on hot days.
INS-WF-CFT1_0520
For further information or to consult this guide online, please visit our website at www.stelpro.com
STELPRO DESIGN INC. | Saint-Bruno-de-Montarville | Quebec | J3V 6L7
Before installing and operating this product, the user and/or installer must read, understand and follow these instructions and keep them handy for future
reference. If these instructions are not followed, the warranty will be considered null and void and the manufacturer deems no further responsibility for this product.
The following instructions must be adhered to in order to avoid personal and serious injuries, property damages and potentially fatal electric shocks.
Switch off the power at the circuit breaker/fuse before installing, repairing and cleaning the unit.
Make sure the unit is appropriate for the intended use (if needed, refer to the product catalog or a representative).
WARNING
WALL FAN HEATER | WF SERIES
BUILT-IN THERMOSTAT INSTALLATION
WF-CFT1 SERIES
1. Remove the grille of the unit.
2. Mount the thermostat to the thermostat mounting bracket. FIG. 1
3. Connect the black wire from the unit to one of the terminals of the
thermostat. FIG. 2
4. Connect the black wire supplied in the kit to the other thermostat
terminal. FIG. 3
5. Fix the thermostat bracket to the unit using the screws supplied.
FIG. 4
6. Connect the unit according to wiring diagram below.
7. Reinstall the grille on the unit and insert the control button or the
cap for a tempered proof solution. FIG. 5
FIG. 1 FIG. 2
FIG. 4FIG. 3
FIG. 5
INSWF-CFT2_0316
For further information or to consult this guide online, please visit our website at www.stelpro.com
STELPRO DESIGN INC. | Saint-Bruno-de-Montarville | Quebec | J3V 6L7
Before installing and operating this product, the user and/or installer must read, understand and follow these instructions and keep them handy for future
reference. If these instructions are not followed, the warranty will be considered null and void and the manufacturer deems no further responsibility for this product.
The following instructions must be adhered to in order to avoid personal and serious injuries, property damages and potentially fatal electric shocks.
Switch off the power at the circuit breaker/fuse before installing, repairing and cleaning the unit.
Make sure the unit is appropriate for the intended use (if needed, refer to the product catalog or a representative).
WARNING
WALL FAN HEATER | WF SERIES
BUilt-in thermostat installation
WF-CFT2 SERIES
1. Remove the grille of the unit.
2. Bend two of the thermostat terminals at a 90° angle. FIG. 1
3. Take the two red wires supplied and connect them to the bent
terminals. FIG. 2
4. Connect the red wire from the unit to one of the red wires connected
to the thermostat using the appropriate wire nut. FIG. 3
5. Connect the black wire of the unit to one unbent terminal of the
thermostat. FIG. 4
6. Connect the black wire supplied in the kit to the other unbent
terminal of the thermostat. FIG. 5
7. Fix the thermostat bracket on the unit using the screws supplied.
FIG. 6
8. Connect the unit according to wiring diagram below.
9. Re-install the grille on the unit and insert the button.
FIG. 1 FIG. 2
FIG. 4
FIG. 6FIG. 5
FIG. 3
  • Page 1 1
  • Page 2 2

Stelpro WF Installation guide

Stelpro
Brand
Stelpro
Model
WF
Type
Installation guide
This manual is also suitable for

Stelpro WF is a wall-mounted fan heater with a built-in thermostat that allows you to control the temperature of your room. It can be easily installed by following the instructions in the manual and is suitable for a variety of applications, including heating small rooms, bathrooms, and workshops. The fan heater has a number of features that make it a great choice for your home, including:

  • Adjustable thermostat: The built-in thermostat allows you to set the desired temperature for your room, and the fan heater will automatically turn on and off to maintain that temperature.
  • Fan-only mode: In addition to heating your room, the fan heater can also be used as a fan only, which is great for circulating air and cooling down your room on hot days.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI