Hogtunes RG4CH-AA Installation guide

Brand: Hogtunes

Model: RG4CH-AA

Type: Installation guide

Hogtunes RG4CH-AA enables a quick and simple installation of a Hogtunes NCA 450-AA amplifier in Road Glides of years 1998-2013 (non-CVO). It also supports mounting of any Hogtunes 2-channel amp or Hogtunes NCA 40.4 in the same location. The kit includes all necessary hardware including screws, nuts and a power harness extension for easy wiring. To ensure a secure fit, the plate is attached to the inner fairing using hook-and-loop adhesive, while the bolts that hold the turn signals in place provide additional support.

Hogtunes RG4CH-AA enables a quick and simple installation of a Hogtunes NCA 450-AA amplifier in Road Glides of years 1998-2013 (non-CVO). It also supports mounting of any Hogtunes 2-channel amp or Hogtunes NCA 40.4 in the same location. The kit includes all necessary hardware including screws, nuts and a power harness extension for easy wiring. To ensure a secure fit, the plate is attached to the inner fairing using hook-and-loop adhesive, while the bolts that hold the turn signals in place provide additional support.

RG4CH-AA Installation Instructions

Hogtunes Inc., Unit 14 - 70 Ellis Drive, Barrie, Ontario, Canada, L4N-8Z3

Tel: (705) - 719-6361 Email: info@hogtunes.com

www.hogtunes.com

The RG4CH-AA properly installs a Hogtunes NCA 450-AA amplier in 1998-2013 (non CVO) Road Glides.

It can also be used to mount any Hogtunes 2 channel amp or Hogtunes NCA 40.4 in the same location.

If Installing a Hogtunes REV 200-AA or NCA 70.2

Using the supplied nuts and screws, attach the amplier

to the plate as shown in above using holes marked “A”.

Have the screws come through from underneath the

plate. Apply 1 side of hook and loop in area shown on

plate. Clean area on inner fairing where other half of

hook and loop adhesive will go. The bolts that hold the

turn signals in place will secure the plate even though

the adhesive does most of the work. Follow amplier

manual for wiring instructions.

Step 1) Turn the NCA 450-AA over and remove the 4 screws

(shown above) on the power connector side of the amplier

Step 2) Put the plate over the amp as shown above and

reinstall 4 screws into holes marked “B”. Apply 1 side of

hook and loop in area shown on plate.

Step 3) Clean area on inner fairing where other half of

hook and loop adhesive will go. The bolts that hold the

turn signals in place will secure the plate even though

the adhesive does most of the work. Plug the supplied

power harness extension into amp and follow

amplier manual for wiring instructions.

If Installing a Hogtunes NCA 40.4

Using the supplied screws, attach the amplier to the

plate as shown in above using holes marked “A”. The

screws will go direct into the underside of amp. Apply 1

side of hook and loop in area shown on plate. Clean area

on inner fairing where other half of hook and loop adhe-

sive will go. The bolts that hold the turn signals in place

will secure the plate even though the adhesive does

most of the work. Follow amplier manual for wiring

instructions.

There is No Aliation Between Harley-Davidson, Inc., and Hogtunes Inc.

NCA 450-AA

1

Hogtunes RG4CH-AA Installation guide

Brand: Hogtunes

Model: RG4CH-AA

Type: Installation guide

Hogtunes RG4CH-AA enables a quick and simple installation of a Hogtunes NCA 450-AA amplifier in Road Glides of years 1998-2013 (non-CVO). It also supports mounting of any Hogtunes 2-channel amp or Hogtunes NCA 40.4 in the same location. The kit includes all necessary hardware including screws, nuts and a power harness extension for easy wiring. To ensure a secure fit, the plate is attached to the inner fairing using hook-and-loop adhesive, while the bolts that hold the turn signals in place provide additional support.

Download PDF

in other languages

eesti: Hogtunes RG4CH-AA paigaldusjuhend

Related papers

Other documents