Bigben Quickfire 2 controller Owner's manual

Brand: Bigben

Model: Quickfire 2 controller

Category: Video games

Type: Owner's manual

ENGLISH FRANÇAIS DEUTSCH NEDERLANDS ESPAÑOL ITALIANO PORTUGUÊS

Thank you for purchasing the Bigben Interactive Quickﬁ re 2 controller. This

product has been designed to enhance your console.

Please keep this instruction manual for future reference. If you require any

assistance or help please contact the Helpline.

WARRANTY

This product bearing the Bigben Interactive trademark, is guaranteed by the

manufacturer for a period of 1 year from the date of purchase, and will, during

this period be replaced with the same or a similar model, at our option, free

of charge, if there is a defect due to faulty material, or workmanship. This

guarantee does not cover defects arising from accidental damage, misuse or

wear and tear, and is available only to the original purchaser of the product. This

does not affect your statutory rights.

THIS PRODUCT INCLUDES:

• Full Colour LCD screen

• 3 axis tilt sensors

• 2 x vibration motors

• Ergonomic, non slip triggers.

• 1x USB Receiver unit

Supplied with 2 x AA Alkaline batteries.

PRODUCT FEATURES*:

• Programmable Quickﬁ re mode

• Dual combo sequence buttons

• Sniper mode

• Duck and ﬁ re mode

• Auto aim mode

• Reverse L\R buttons

• Auto reload \weapon swap mode

• Button logging

• Illuminated \ Flashing buttons

* Please note that certain features may not be compatible with all games

CONTROLLER SET-UP AND USE

Battery Installation

01. Remove the battery compartment cover from underneath the controller

02. Insert 2 x 1.5 volt AA size batteries, observing the correct polarity

03. Reﬁ t the battery compartment cover.

PORTUGUÊS ITALIANO ESPAÑOL NEDERLANDS DEUTSCH FRANÇAIS ENGLISH

Using the Controller with a PS3™

Slide the switch on the Receiver Unit to PS3™ mode.

Receiver Connection

Plug the Receiver Unit into one of the USB ports on your PS3™ console. The

Red LED on the Receiver Unit will ﬂ ash constantly.

Using your Controller

01. Switch on the controller by sliding the power On/Off switch on the

controller to on. The LCD screen will then Illuminate.

02. Press the `PS Home’ button on the centre of the controller. This is the button

with the house symbol.

03. The controller will connect to your PlayStation®3 console and your player

number will be indicated in the top left of the LCD screen.

04. The controller will connect to your PlayStation®3 console and your player

number will be indicated in the top left of the LCD screen.

05. Ensure that your controller is assigned as controller 1.

If it is not recognised as controller 1, press and hold the home button

to bring up the option menu, while you have a game loaded. Select the

controller settings and then select the ‘Reassign the Controller’ option. Scroll

down with the D-pad on the controller until it says 1 on the TV screen. Press

X to select it and then press O twice to go back to your game.

* For further information on assigning controller ports please refer to your console

instruction manual.

01. Controller \ player number

02. Active setting

03. Battery level indicator (Green when full, Yellow when part full. Red when

low).

04. Mode icons. Active options are green. Inactive options are red.

ENGLISH FRANÇAIS DEUTSCH NEDERLANDS ESPAÑOL ITALIANO PORTUGUÊS

Using the settings on your controller.

Your Quickﬁ re 2 controller has been designed so it can be easily set up using

the LCD screen. The modes can be activated, deactivated and customised using

the simple icon system.

Firstly, give a short press on the Home button to enter the settings screen.

Use the left controller stick to move between the different icons. The selected

icon will have a white frame around it to indicate it is currently selected. Press

the start button to choose this feature.

This will then take you to another screen where you can switch the feature

on or off by selecting Y or N. You can also reprogram some of the features,

depending on the mode selected. If the feature is switched on, the icon will

appear in green. If the feature is off it will appear in red.

Using the Quick mode buttons

4 of the features can be switched on and off quickly during play, so you do not

have to enter the settings mode whilst in a game.

There are 2 buttons on the underside of the controller that are used for this.

To switch these features on and off during play, use the following actions.

• A short press of the left button for less than 1 sec toggles sniper mode on and off.

• A long press of the left button for 1 second or more toggles rapid ﬁ re on and off.

• A short press of the right button for less than 1 sec toggles duck and ﬁ re on and off.

• A long press of the right button for 1 second or more toggles auto aim on and off.

Set selection

For convenience, your Quickﬁ re 2 controller has memory to recall 2 different

custom settings. This is useful if you want to make 2 custom settings for 2

different games, without having to re-programme each time. To choose your

setting, follow these steps.

01. Short press the Home button to enter the settings page mode.

02. Move down with the left stick to go down to the lower row of options.

03. Select the Set1 \ Set2 icon and press the select button.

04. Choose Set 1 or Set 2 and press select.

PORTUGUÊS ITALIANO ESPAÑOL NEDERLANDS DEUTSCH FRANÇAIS ENGLISH

05. The screen will then return to the home page and S1 or S2 will be dislayed

at the top of the screen to indicate what setting you are on. All changes

will then be saved to that Set.

06. If you want to program a different set of instructions for a different game,

simply change the set number.

IMPORTANT: When changing between your Set 1 and Set 2 settings you also need to

reselect your P1 and P2 settings in the combo options, if you want to use this function.

Please check the combo button section for full instructions.

MODES

Quickﬁ re* The Quickﬁ re 2 controller has 6 different Quickﬁ re modes to suit all

of your favourite shooting games. The controller is set to Mode 1

which is 8 shots per second by default.

The mode is displayed on the LCD screen as M1 08SPS. Quick ﬁ re is set to the R1

button of your controller as this is the most common ﬁ ring button for shooting

games. Rapid ﬁ re is switched on by default. The Icon is highlighted as green to

indicate that it is active.

To switch Quickﬁ re mode off in the menu, select the Quickﬁ re icon and select

‘N’.

ENGLISH FRANÇAIS DEUTSCH NEDERLANDS ESPAÑOL ITALIANO PORTUGUÊS

Changing the quickﬁ re modes

The quickﬁ re modes have been designed to work on all of your shooting

games. To ensure full compatibility please select the correct mode for your

game.

The modes are as follow:

M1 8SPS – Call of Duty 4 Modern Warfare

M2 10SPS – Call of Duty World at War and Call of Duty: Black Ops

M3 20SPS – Call of Duty Modern Warfare 2

M4 32SPS – Call of Duty Modern Warfare 2

M5 48SPS - Call of Duty Modern Warfare 2

Please note that modes M4 and M5 may have varied results depending on

which guns you are using in the game. If you experience any problems, stick

with the M3 mode.

These modes will also work with other popular shooting games, like Battleﬁ eld,

Killzone, Resistance etc. Try the different modes to select which works best.

TO CHANGE BETWEEN MODES FOLLOW THESE STEPS:

01. Short press the Home button to enter the settings page mode.

02. Select the Rapid ﬁ re icon and press the start button.

03. Use the left stick to move to the M1 position in the settings screen.

04. Move the left stick up or down to select the mode you want to use.

05. Press the select button to choose the ﬁ ring mode you want to use. The

screen will then return to the home page.

06. The controller will now ﬁ re at your chosen speed when you press R1.

CUSTOM QUICKFIRE MODE

The Quickﬁ re 2 controller also includes a custom mode to ensure future

compatibility with new games and so you can experiment with different ﬁ ring

rates. The rates can range for 6 shots to 60 shots per second.

PORTUGUÊS ITALIANO ESPAÑOL NEDERLANDS DEUTSCH FRANÇAIS ENGLISH

To set the custom ﬁ ring rates follow these steps:

01. Short press the Home button to enter the settings page mode.

02. Select the Rapid ﬁ re icon and press the start button.

03. Use the left stick to move to the M1 position in the settings screen.

04. Move the left stick up or down to the M6 position.

05. When M6 is selected, move the left stick to the right to select the shots per

second rate (SPS).

06. Move the left stick up or down to adjust the ﬁ ring rate to your desired

selection.

07. Press select to conﬁ rm your selection. The screen will then return to the

home page.

08. The controller will now ﬁ re at your chosen speed when you press R1. Please

note that some guns in some games may not function correctly at certain

rates. You will need to experiment to ﬁ nd out which rate works best for your

game.

Programming other buttons for Quickﬁ re mode

By default, only the R1 button is used for Quickﬁ re, but if you are playing games

that use another button for ﬁ ring, you can also program.

To set other buttons for Quickﬁ re, follow these steps:

01. Short press the Home button to enter the settings page mode.

02. Select the Rapid ﬁ re icon and press the start button.

03. Move the left stick to select the rapid ﬁ re button selections at the bottom of

the screen. R1 should currently be shown.

04. Now press any other button you wish to assign as rapid ﬁ re, R2 for example.

R2 will now be displayed at the bottom of the screen, alongside R1.

05. You can select up to 4 different buttons for the rapid ﬁ re action. To switch

them off again, just press the same button again.

ENGLISH FRANÇAIS DEUTSCH NEDERLANDS ESPAÑOL ITALIANO PORTUGUÊS

06. Press select to conﬁ rm your selection. The screen will then return to the

home page.

07. Your button selections will now have rapid ﬁ re all at the same ﬁ ring rate.

Disable Quickﬁ re on R1 button

To disable rapid ﬁ re on the R1 button, follow the same instructions as noted

above and press the R1 button to deselect it. The R1 button will then disappear

from the bottom of the screen.

Quickﬁ re toggle on \ off

The QuickFire 2 controller has 2 underside buttons which allow you to quickly

switch Quickﬁ re mode on and off with a single button press, without having to

go into the menu.

To switch on / switch off Quickﬁ re mode, follow these steps:

01. Hold the left button for 1 second to switch Quickﬁ re mode On.

02. Controller emits 2 beeps to indicate that Quickﬁ re is On.

PORTUGUÊS ITALIANO ESPAÑOL NEDERLANDS DEUTSCH FRANÇAIS ENGLISH

03. Hold again to switch it back Off.

04. Controller emits a beep to indicate that Quickﬁ re is off.

05. The Rapid ﬁ re icon will also change colour to show that it is on or off.

Sniper mode*

The Sniper mode allows you to adjust the sensitivity and dead band of

the right stick for better aiming. This mode is programmable to let you

ﬁ nd the best setting.

Sensitivity can be adjusted from 20% to 100% in 5% increments. Dead band

cancellation can be adjusted from 0 to 30% in 2% increments. By default,

sensitivity is set to 50% and deadband is 10%.

Sniper mode is switched off by default and the icon will appear red.

To switch it on enter the settings screen, select the sniper mode and select Y.

The sniper mode icon will then appear green.

To set the sensitivity, follow these steps:

01. Short press the Home button to enter the settings page mode.

02. Select the Sniper mode icon on the menu with left stick, and press start to

enter mode setting.

03. Move the left stick right to the ‘S’ position to adjust the sensitivity.

04. Move the left stick up or down to increase or decrease the amount of

sensitivity you want on the stick.

ENGLISH FRANÇAIS DEUTSCH NEDERLANDS ESPAÑOL ITALIANO PORTUGUÊS

05. Move the left stick right to the ‘T’ position to adjust the deadzone threshold.

06. Move the left stick up or down to increase or decrease the amount of

deadzone you want on the stick. A lower deadzone will mean that the stick

will move at the slightest touch. A higher deadzone will mean that you will

need to move the stick more before it will activate.

07. Press select to conﬁ rm your selection and return to the menu screen.

Sniper mode toggle on \ off :

The Sniper mode can be switched on and off on during play using the buttons

underside the controller.

To switch on /switch off Sniper mode, follow these steps:

01. Hold the left button for less than1 second to switch Sniper mode On.

02. Controller emits 2 beeps to indicate that the mode is On.

03. Hold the left button for less than1 second to switch it back Off

04. Controller emits a beep to indicate that Sniper mode is off.

05. The Sniper icon will also change colour to show that it is on or off.

Duck and Fire mode (D&F)*

The duck and ﬁ re mode instantly makes your character go prone or

crouch and shoot, so you can evade the enemy and take them out.

This mode is programmable as it depends on the game and buttons

used to duck and crouch.

By default, button mapping is the current ﬁ ring button and O button for

crouch. D&F is off by default and the icon is red. To switch it on enter the

settings screen, select the duck and ﬁ re mode and select Y. The duck and ﬁ re

mode icon will then appear green.

PORTUGUÊS ITALIANO ESPAÑOL NEDERLANDS DEUTSCH FRANÇAIS ENGLISH

Editing D&F mode

If your game uses different buttons other than R1 to shoot and O to crouch you

will need to edit the sequence. To do this, follow these steps:

01. Short press the Home button to enter the settings page mode.

02. Select the Duck and Fire icon and press the start button.

03. Use the left stick to move to the Edit position and press start.

04. Enter the correct buttons for shoot and duck in the spaces provided.

05. Press select to conﬁ rm your selection. The screen will then return to the

home page.

STEP 01

ENGLISH FRANÇAIS DEUTSCH NEDERLANDS ESPAÑOL ITALIANO PORTUGUÊS

Additional editing options

The editing feature can be used on the D&F, Auto Aim, Auto Reload and Combo

modes. It also has 3 additional options that can be used.

01. When starting the editor, if you move the left stick to the left one step, you

will ﬁ nd the ‘Timing option.’ This allows you to edit the gap timing between

each step. To use this simply go to the ‘TR’ option, press start and then push

up or down on the left stick to change the timing. The timing can be set

between 5ms and 100ms and will increase or decrease in 5ms steps each

time.

02. If you move the left stick to the left 2 step, you will ﬁ nd the ‘Clear’ option.

This allows you to clear the whole sequence rather than alter it step by step.

To use simply go to the ‘CL’ option, press start and the current sequence will

be cleared. You can then start again at step one.

PORTUGUÊS ITALIANO ESPAÑOL NEDERLANDS DEUTSCH FRANÇAIS ENGLISH

03. If you move the left stick to the left 3 steps you will ﬁ nd the default settings

option. This will reset the chosen sequence back to the factory default. To

use simply go to the ‘DF’ option, press start and factory setting will be reset.

This is particulary useful if you are having troubles with the chosen feature

after editing.

D&F mode toggle on \ off :

The D&F mode can be switched on and off on during play using the buttons on

the underside the controller.

To switch on / switch off D&F mode, follow these steps:

01. Press the right button for less than one second to switch the D&F mode on.

02. Controller emits 2 beeps to indicate that the mode is on.

03. Press the right button again for less than one second to switch it back off.

04. Controller emits a beeps to indicate that Sniper mode is off.

05. The D&F icon will also change colour to show that it is on or off.

Auto Aim Mode*

The auto aim mode automatically tracks your enemy. It works in

conjunction with looking down the sights to improve your aim.

By default this mode is mapped to L1.

ENGLISH FRANÇAIS DEUTSCH NEDERLANDS ESPAÑOL ITALIANO PORTUGUÊS

To switch it on enter the settings screen, select the Auto aim mode and select Y.

The Auto aim mode icon will then appear green.

Set aim \ iron sights button

The button for aim \ Iron sights can be edited.

To set aim \ iron sights button, follow these steps:

01. Short press the Home button to enter the settings page mode.

02. Select the auto aim icon and press the start button.

03. Use the left stick to move to the aim position button. It will display L1 as

default.

04. Press the button you now wish to assign as aim \ ironsights.

05. Press select to conﬁ rm your selection. The screen will then return to the

home page.

Auto Aim timing

The auto aim timing can be edited.

The default timing sequence is 60ms on and 20ms off, and repeat the sequence.

You should not really need to alter this setting, but if you ﬁ nd a game that does

not quite function correctly, you can try and ﬁ x the issue with this option.

PORTUGUÊS ITALIANO ESPAÑOL NEDERLANDS DEUTSCH FRANÇAIS ENGLISH

IMPORTANT ! As noted above, this function will not with all games, so even editing the

sequence may not resolve it.

To edit the sequence, follow these steps:

01. Short press the Home button to enter the settings page mode.

02. Select the auto aim icon and press the start button.

03. Use the left stick to move to the Edit position and press start.

04. Move the left stick up or down to adjust the ON timing.

05. Move the left stick right to the next position.

06. Move the left stick up or down to adjust the OFF timing.

07. Press select to conﬁ rm your selection. The screen will then return to the

home page.

Auto aim mode toggle on \ off :

The auto aim mode can be switched on and off on during play using the

buttons underside the controller.

To switch on /switch off auto aim mode, follow these steps:

01. Hold the right button for 1 second to switch auto aim mode On.

02. Controller emits 2 beeps to indicate that auto aim is On.

03. Hold the right button again for 1 second to switch it back Off.

ENGLISH FRANÇAIS DEUTSCH NEDERLANDS ESPAÑOL ITALIANO PORTUGUÊS

04. Controller emits a beep to indicate that auto aim is off.

05. The auto aim icon will also change colour to show that it is on or off.

Swap L\R BUTTONS*

This feature allows the R1 or L1 buttons to be mapped to the R2 and L2

buttons and vice versa. This is useful for those players that prefer to use

the lower shoulder buttons for shooting. This option can only be

activated/desactivated in the menu. By default, this feature is off.

To switch it on enter the settings screen, select the Swap L\R icon and select Y.

The Swap L \ R mode icon will then appear green.

Combo buttons*

The Quickﬁ re 2 controller has 2 extra buttons on front face for

programming macro sequences. A 30 move sequence can be

programmed onto each of the 2 buttons. X, square, triangle, circle, L

and R buttons and D-pad can all be programmed in a sequence. This function is

particularly useful for ﬁ ghting games that use long and complex combinations

to activate special moves.

The default for these buttons is an empty sequence with a 20ms timing gap

selected.

PORTUGUÊS ITALIANO ESPAÑOL NEDERLANDS DEUTSCH FRANÇAIS ENGLISH

To edit a sequence, follow these steps:

01. Short press the Home button to enter the settings page mode.

02. Move down with the left stick to show the bottom row of icons and select

the combo icon and press the start button.

03. Select the P1 or P2 option. And press start. P1 represents the left combo

button and P2 represents the right combo button.

04. Press the ﬁ rst action button for your sequence. Then push right on the

left stick to move to the next button position. You will also see that the

sequence position number is shown on the screen. This number will

increase by one each time a new step is added.

05. The screen will display a dash to indicate that there will be another button

press in the sequence. The dash gives a 20 millisecond (ms) gap.

06. Then press the next button in your sequence, followed by another push to

the right. This will insert the next button in your sequence.

07. Continue this until you have inserted all of your required moves.

08. If you wish to insert a D-pad press direction in the sequence, simply push

the direction you require in the sequence in the same way as inserting a

button press. It will be represented on the screen as an arrow to show the

direction you have selected.

09. If you wish to have a simultaneous button press or D-pad press in the

sequence, do not push right on the stick. Push and hold the ﬁ rst button in

the sequence and then press the next required button. The selected move

will appear on the screen WITHOUT a dash inbetween. The shows that the

required move is a simultaneous press. To add more simultaneous button

presses, continue to hold the ﬁ rst button and then enter the other button

presses.

10. Some games may require a slight pause in the sequence to complete the

required move. If you wish to insert a short gap or space in the sequence,

simply press up on the joystick. This will then insert a 20ms gap in the

combo. For longer gaps, simply insert more spaces. You may need to

experiment with the game to see what works best.

11. To delete a move, simply press down on the left stick. The move will then be

deleted.

12. To edit any of the moves in your current sequence, press left on the stock to

go back to the step you want to edit. You can then delete the move and \ or

insert a new step in the sequence. You can see what position you are at in

the sequence by checking the number at the top of the screen.

13. Press select to conﬁ rm your selection. The screen will then return to the

home page.

ENGLISH FRANÇAIS DEUTSCH NEDERLANDS ESPAÑOL ITALIANO PORTUGUÊS

IMPORTANT: When swapping between your Set 1 and Set 2 selections you will also need

to reselect the P1 and P2 settings if you intend to use the 2 different combo settings. To

do this, simply go to the combo icon and press start to check your combo sequences are

loaded. Check both the P1 and P2 settings by pressing start on each one. This will then

ensure the correct sequences are loaded.

Auto reload / Weapon Swap*

The Auto reload / weapon swap mode automatically reloads or

changes your weapon when you have run out of ammo. This is useful

for those games that do not include this feature as standard. This

option can be switched on in the menu. By default Auto reload mode is Off.

To switch it on enter the settings screen, select the Auto reload mode and

select Y. The Auto aim mode icon will then appear green.

*Depends on the game

(example: Zombie mode in Call Of Duty: Black Ops).

PORTUGUÊS ITALIANO ESPAÑOL NEDERLANDS DEUTSCH FRANÇAIS ENGLISH

Editing Auto reload / weapon swap mode

If your game uses different buttons other than square to reload and triangle

to change weapon, you will need to edit the sequence. To do this, follow these

steps:

01. Short press the Home button to enter the settings page mode.

02. Select the Auto reload icon and press the start button.

03. Use the left stick to move to the Edit position and press start.

04. Enter the correct buttons for reload and weapon swap in the spaces

provided.

05. Press select to conﬁ rm your selection. The screen will then return to the

home page.

Toolbox settings

The toolbox settings page allows access to 3 additional features:

• Button logging statistics

• LED options

• Full factory reset

ENGLISH FRANÇAIS DEUTSCH NEDERLANDS ESPAÑOL ITALIANO PORTUGUÊS

To enter the Tool Box follow these steps

01. Short press the Home button to enter the settings page mode.

02. Move down with the left stick to go down to the lower row of options.

03. Select the toolbox icon in the bottom right corner of the screen and press

the select button.

04. You can then select one of the 3 options.

Button logging statistics

This feature records all of the button presses, so you can see which button is

being pressed the most. This can be checked by current session and a total

cumulative count from when the controller was ﬁ rst powered on. These totals

Page is loading ...

Bigben Quickfire 2 controller Owner's manual

Brand: Bigben

Model: Quickfire 2 controller

Category: Video games

Type: Owner's manual

Download PDF

report

Bigben Quickfire 2 controller Owner's manual

Bigben Quickfire 2 controller Owner's manual

Related papers

Other documents