Molift RgoSling Ambulating Vest User manual
- Type
- User manual
RgoSling
Sling assessment protocol (EN)
UP40001 Rev B 2021-09-08
2
Molift RgoSling / www.etac.com
Contents
Use the test protocol together with the manual for the relevant
sling for individual testing.
The manual for both the hoist and sling must be
thoroughly read before use
It is crucial that the sling is individually fitted for the intended user
and intended lifting situations where the sling will be used.
Make the decision on whether one or more carers are required.
Plan the lifting operation in advance to ensure that it is as safe and
smooth as possible. Think about ergonomic working positions.
Assess the risks and take notes. The carer is responsible for the
safety of the user.
Always check:
• That the user is capable of using the sling.
• That the model, size and material are suitable.
• That the sling is suitable for the sling bar to be performed
• It is important to check that the strap loops are correctly
attached to the sling bar’s hooks before lifting the user
• Make sure wheels on the wheelchair or bed etc. are locked
when necessary during the procedure
Never use a faulty or damaged sling as it can
break and cause personal injury. Destroy and
discard damaged and old slings.
The sling should not be stored in direct sunlight.
Periodic Inspection
Periodic inspection must be carried out at least every 6 months.
More regular inspections may be required if the sling is used or
washed more often than normal. See the periodic inspection
protocol at www.etac.com.
Visit www.etac.com for more information,
advice and any documentation updates.
Safety instructions
Contents
Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Assessment protocol RgoSling HighBack / MediumBack . . . . . . . 3
Assessment protocol RgoSling Toilet HighBack / LowBack . . . . . . 4
Assessment protocol RgoSling Ampu HighBack / MediumBack . . 5
Assessment protocol RgoSling StandUp (w/support) . . . . . . . . . . 6
Assessment protocol RgoSling Active . . . . . . . . . . . . . . . . . . . . . 7
Assessment protocol RgoSling Comfort HighBack . . . . . . . . . . . . 8
Assessment protocol RgoSling Ambulating Vest . . . . . . . . . . . . . 9
Assessment protocol RgoSling Fabric Stretcher . . . . . . . . . . . . . 10
Assessment protocol RgoSling MediumBack Plus . . . . . . . . . . . 11
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3
Molift RgoSling / www.etac.com
Sling bar Width
4-point
sling bar ..................... (cm)
2-point
sling bar ..................... (cm)
A Leg support loops 1 External, red 2 Light grey 3 Grey 4 Black
The leg support loops selected
determine the sitting angle of
the user and how the pressure
is distributed. Selecting the
red leg support loop (1)
provides an upright position
and more pressure on the legs.
The black leg support loops (4)
provide a more reclined position
and less pressure on the legs.
B Upper lifting strap
The sliding loop balances weight distribution during the lifting process.
Leg support connector Crossed Separate Wrapped
Select the leg support connector which is most
comfortable and safe for the lift. Crossed leg
supports are recommended.
Transfer Horizontal Sitting
From position. Highlight the transfers that have been
tested and approved.
To position. Highlight the transfers that have been tested
and approved.
Note
It is important that the sling has been tested with the individual
user and for the intended lifting situation. Identify the best pos-
sible solution for the user by using both the test protocol and
the manual for the relevant sling during testing.
Information about the user
Name: .......................................................................................
Height (cm): .......................... Weight (kg): ............................
Product information
Item no.: .............................................................................
Material: Padded polyester Polyester net
Variant HighBack
(with head support)
MediumBack
(without head support)
Size: XXS XS S M L XL XXL
Serial no.: .....................................................................
Assessment protocol RgoSling HighBack / MediumBack
HighBack
MediumBack
Etac A/S
Parallelvej 3
DK-8751 Gedved
www.etac.com
Testing and risk assessment performed by
Name: ...................................................................................................................
Date: .................................. Signature: ..........................................................
Use a permanent marker to mark.
Mark the first time of use on the label and set a date for the first periodical inspection.
Mark the label with the name of the user - start at the bottom!
The previous name can then be cut off if the sling is used by a new user.
A
A
B
B
1 2 3 4
4
Molift RgoSling / www.etac.com
Sling bar Width
4-point
sling bar ..................... (cm)
2-point
sling bar ..................... (cm)
A Leg support loops 1 External, red 2 Light grey 3 Grey 4 Black
The leg support loops selected
determine the sitting angle of
the user and how the pressure
is distributed. Selecting the
red leg (1) support loop provides
an upright position and more
pressure on the legs. The black
leg support loops (4) provide a more
reclined position and less pressure
on the legs.
B Upper lifting strap loops 1 External, red 2 Light grey 3 Grey 4 Black
The lifting strap loops selected
determine the sitting angle of the
user and pressure distribution.
Lifting strap loops (4) provide a more
upright position and more pressure on
the legs. Lifting strap loops (1) provide
a more reclined position and less
pressure on the legs.
C Leg support connector Crossed Wrapped Separate
Select the leg support connector which is most comfort-
able and safe. Crossed leg supports are recommended.
There is an increased risk of sliding forward out of the
sling when using wrapped or separate connectors on
each side.
Transfer Sitting Toilet
From position. Highlight the transfers that have been tested and
approved.
To position. Highlight the transfers that have been tested and
approved.
Note
It is important that the sling has been tested with the individual
user and for the intended lifting situation. Identify the best pos-
sible solution for the user by using both the test protocol and
the manual for the relevant sling during testing.
Information about the user
Name: .......................................................................................
Height (cm): .......................... Weight (kg): ............................
Product information
Item no.: .............................................................................
Model HighBack
(with head support)
LowBack
(without head support)
Size: XXS XS S M L XL XXL
Serial no. .............................................................................
1 2 3 4
1 2 3 4
Assessment protocol RgoSling Toilet HighBack / LowBack
HighBack
LowBack
Etac A/S
Parallelvej 3
DK-8751 Gedved
www.etac.com
A
C
B
A
C
B
Testing and risk assessment performed by
Name: ...................................................................................................................
Date: .................................. Signature: ..........................................................
Use a permanent marker to mark.
Mark the first time of use on the label and set a date for the first periodical inspection.
Mark the label with the name of the user - start at the bottom!
The previous name can then be cut off if the sling is used by a new user.
5
Molift RgoSling / www.etac.com
Sling bar Width
4-point
sling bar ..................... (cm)
2-point
sling bar ..................... (cm)
A Leg support loops 1 External, red 2 Light grey 3 Grey 4 Black
The leg support loops selected
determine the sitting angle of
the user and how the pressure
is distributed. Selecting the red leg
support loop (1) provides an upright
position and more pressure on the
legs. The blackleg support loops (4)
provides a more reclined position
and less pressureon the legs.
B Upper lifting strap Sliding hook Fixed hook
The recommended configuration uses sliding loops to
ensure balanced pressure distribution during lifting. The
locked hook, as an alternative, results in an upright position.
Leg support connector Wrapped Crossed
Select the leg support connector which is most
comfortable and safe for the lift. Wrapped connectors
are recommended.
C Belt With belt Without belt
The sling can be used without a belt but this results in a risk
of falling forward. Use of the sling without a belt can be
recommended only when using crossed leg supports or a
reclined position.
Transfer Horizontal Sitting
From position. Highlight the transfers that have been tested
and approved.
To position. Highlight the transfers that have been tested and
approved.
Note
It is important that the sling has been tested with the individual
user and for the intended lifting situation. Identify the best pos-
sible solution for the user by using both the test protocol and
the manual for the relevant sling during testing.
Information about the user
Name: .......................................................................................
Height (cm): .......................... Weight (kg): ............................
Product information
Item no.: .............................................................................
Model HighBack
(with head support)
MediumBack
(without head support)
Size: XXS XS S M L XL XXL
Serial no.: .............................................................................
1 2 3 4
Assessment protocol RgoSling Ampu HighBack / MediumBack
MediumBack
HighBack
C
Etac A/S
Parallelvej 3
DK-8751 Gedved
www.etac.com
A
A
B
B
Testing and risk assessment performed by
Name: ...................................................................................................................
Date: .................................. Signature: ..........................................................
Use a permanent marker to mark.
Mark the first time of use on the label and set a date for the first periodical inspection.
Mark the label with the name of the user - start at the bottom!
The previous name can then be cut off if the sling is used by a new user.
6
Molift RgoSling / www.etac.com
Lifting arm
V-shaped 2-point
Lifting arm
U-shaped 2-point
Lifting arm
A Strap attachment From the
inside
From the
outside
The V-shaped lifting arm has been designed so that
the cords can be attached from the inside or the outside.
For larger users it is recommended that the cords are
attached from the outside to create a larger opening.
Make sure the cords are fastened with equal length on
both sides of the user.
Max 10 cm gap between right and left side of waist belt
padding.
Transfer Sitting Toilet
From position. Highlight the transfers that have been
tested and approved.
To position. Highlight the transfers that have been tested
and approved.
Note
It is important that the sling has been tested with the individual
user and for the intended lifting situation. Identify the best pos-
sible solution for the user by using both the test protocol and
the manual for the relevant sling during testing.
Information about the user
Name: .......................................................................................
Height (cm): .......................... Weight (kg): ............................
Product information
Item
no.:
.............................................................................
Model StandUp w/Support
(with bottom sling)
StandUp
(without bottom sling)
Size: XS S M L XL
Serial
no.:
.............................................................................
Assessment protocol RgoSling StandUp (w/support)
StandUp
StandUp w/support
Etac A/S
Parallelvej 3
DK-8751 Gedved
www.etac.com
A
A
Testing and risk assessment performed by
Name: ...................................................................................................................
Date: .................................. Signature: ..........................................................
Use a permanent marker to mark.
Mark the first time of use on the label and set a date for the first periodical inspection.
Mark the label with the name of the user - start at the bottom!
The previous name can then be cut off if the sling is used by a new user.
7
Molift RgoSling / www.etac.com
Lifting arm
4-point lifting arm
A Sling attachment
Fasten the sling to all four suspension hooks. Make sure the lifting
straps are fastened with equal length on both sides of the user.
Max 10 cm gap between right and left side of waist belt padding.
Transfer Sitting Toilet
From position. Highlight the transfers that have been
tested and approved.
To position. Highlight the transfers that have been tested
and approved.
Note
It is important that the sling has been tested with the individual
user and for the intended lifting situation. Identify the best pos-
sible solution for the user by using both the test protocol and
the manual for the relevant sling during testing.
Information about the user
Name: .......................................................................................
Height (cm): .......................... Weight (kg): ............................
Waist (cm): ..........................
Product information
Item no.: .............................................................................
Size: XS S M L XL
Serial no. .............................................................................
Assessment protocol RgoSling Active
Etac A/S
Parallelvej 3
DK-8751 Gedved
www.etac.com
20212022 2023 2024 2025 2026 2027 2028
Periodic inspection performed.
Date of first use.
YEAR
User name / Namn
MONTH
Product name
xxxxxxx Size XX
Barcode according to GS1-128
(01)xxxxxxxxxxxxxx(11)xxxxxx(21)xxxxxxxx
(01):GTIN number (11):Date (21):Serial number
YYYY-MM-DD
M
RgoSling Active
A
A
Testing and risk assessment performed by
Name: ...................................................................................................................
Date: .................................. Signature: ..........................................................
Use a permanent marker to mark.
Mark the first time of use on the label and set a date for the first periodical inspection.
Mark the label with the name of the user - start at the bottom!
The previous name can then be cut off if the sling is used by a new user.
8
Molift RgoSling / www.etac.com
Sling bar Width
4-point
sling bar ..................... (cm)
2-point
sling bar ..................... (cm)
A Leg support loops 1 External, red 2 Light grey 3 Grey 4 Black
The leg support loops
selected determine the sit-
ting angle of the user and
the pressure distribution
of the weight.
Selecting the red leg
support loops (1), provides
a more upright position.
The black leg support
loops (4) provide a more
reclined position and less
pressure on the legs.
Transfer Horizontal Sitting
From position. Highlight the transfers that have been
tested and approved. N/A
To position. Highlight the transfers that have been tested
and approved.
N.B. The sling has been designed to remain under the user when sitting in a wheelchair.
Note
It is important that the sling has been tested with the individual
user and for the intended lifting situation. Identify the best pos-
sible solution for the user by using both the test protocol and
the manual for the relevant sling during testing.
Information about the user
Name: .......................................................................................
Height (cm): .......................... Weight (kg): ............................
Product information
Item no.: .............................................................................
Size: XS S M L XL XXL
Serial no. .............................................................................
A
1 2 3 4
Assessment protocol RgoSling Comfort HighBack
Etac A/S
Parallelvej 3
DK-8751 Gedved
www.etac.com
Testing and risk assessment performed by
Name: ...................................................................................................................
Date: .................................. Signature: ..........................................................
Use a permanent marker to mark.
Mark the first time of use on the label and set a date for the first periodical inspection.
Mark the label with the name of the user - start at the bottom!
The previous name can then be cut off if the sling is used by a new user.
9
Molift RgoSling / www.etac.com
Sling bar Width
4-point
sling bar ..................... (cm)
2-point
sling bar ..................... (cm)
A Lifting strap
loops 1 External, red 2 Light grey 3 Grey 4 Black
Use the same height/
colour for all four lifting
strap loops.
B Groin strap Without Size
Groin strap XXS-XS S-M L-XL
Transfer Sitting Toilet
From position. Highlight the transfers that have been
tested and approved.
To position. Highlight the transfers that have been tested
and approved.
Therapy/training Gait training Standing
Highlight the transfers that have been tested and
approved.
Note
It is important that the sling has been tested with the individual
user and for the intended lifting situation. Identify the best pos-
sible solution for the user by using both the test protocol and
the manual for the relevant sling during testing.
Information about the user
Name: .......................................................................................
Height (cm): .......................... Weight (kg): ............................
Product information
Item no.: .............................................................................
Size: XXS XS S M L XL
Serial no. .............................................................................
1 2 3 4
Assessment protocol RgoSling Ambulating Vest
Etac A/S
Parallelvej 3
DK-8751 Gedved
www.etac.com
A
B
Testing and risk assessment performed by
Name: ...................................................................................................................
Date: .................................. Signature: ..........................................................
Use a permanent marker to mark.
Mark the first time of use on the label and set a date for the first periodical inspection.
Mark the label with the name of the user - start at the bottom!
The previous name can then be cut off if the sling is used by a new user.
10
Molift RgoSling / www.etac.com
Sling bar
8-point, SWL 255kg
for Parter 255
8-point, SWL 300kg
for Molift Air
A Upper lifting strap loops at the head 1 External, red 2 Light grey 3 Grey
Use the same colour on both sides of the
head. Adjust for optimal positioning and
support of the head.
B Lifting strap loops at the shoulders 1 External red 2 Light grey
Use the same height/colour on both sides.
C Lifting strap loops at the hips 1 External red 2 Light grey
Use the same height/colour on both sides.
D Lower lifting strap loops 1 External red 2 Light grey
Use the same height/colour on both sides.
Note
It is important that the sling has been tested with the individual
user and for the intended lifting situation. Identify the best pos-
sible solution for the user by using both the test protocol and
the manual for the relevant sling during testing.
Information about the user
Name: .......................................................................................
Height (cm): .......................... Weight (kg): ............................
Product information
Item no.: .............................................................................
Size: M L XL
Serial no. .............................................................................
M
Rgosling Fabric Stretcher
M
Rgosling Fabric Stretcher
M
Rgosling Fabric Stretcher
M
Rgosling Fabric Stretcher
Assessment protocol RgoSling Fabric Stretcher
DCBA
Etac A/S
Parallelvej 3
DK-8751 Gedved
www.etac.com
Testing and risk assessment performed by
Name: ...................................................................................................................
Date: .................................. Signature: ..........................................................
Use a permanent marker to mark.
Mark the first time of use on the label and set a date for the first periodical inspection.
Mark the label with the name of the user - start at the bottom!
The previous name can then be cut off if the sling is used by a new user.
11
Molift RgoSling / www.etac.com
Sling bar Width
4-point
sling bar 550 cm 650 cm
4-point
steel sling
bar
One size
A Upper Lifting
strap loops 1 External, red 2 Light grey 3 Grey 4 Black
The lifting strap loops
selected determine the
reclined sitting angle of
the user and pressure
distribution.
B Central legstrap loops 1 External, red 2 Light grey 3 Grey 4 Black
The central legstraps can
either be crossed (fig. 1) or
separate (fig. 2) depending on
the needs for the user.
C Outer legstrap loops 1 External, red 2 Light grey 3 Grey 4 Black
Choose the appropriate leg-
strap combination according
to the individual needs
Central legstrap connector Crossed Separate
The central legstraps can either be crossed (fig. 1) or separate
(fig. 2) depending on the needs for the user.
Transfer Horizontal Sitting
From position. Highlight the transfers that have been
tested and approved.
To position. Highlight the transfers that have been tested
and approved.
Note
It is important that the sling has been tested with the individual
user and for the intended lifting situation. Identify the best pos-
sible solution for the user by using both the test protocol and
the manual for the relevant sling during testing.
Information about the user
Name: .......................................................................................
Height (cm): .......................... Weight (kg): ............................
Product information
Item no.: .............................................................................
Size: L XL
Serial no. .............................................................................
1 2 3 4
Assessment protocol RgoSling MediumBack Plus
Etac A/S
Parallelvej 3
DK-8751 Gedved
www.etac.com
A
A
C
C
B
B
Fig. 1 Crossed
Fig. 2 Separate
Testing and risk assessment performed by
Name: ...................................................................................................................
Date: .................................. Signature: ..........................................................
Use a permanent marker to mark.
Mark the first time of use on the label and set a date for the first periodical inspection.
Mark the label with the name of the user - start at the bottom!
The previous name can then be cut off if the sling is used by a new user.
12
Molift RgoSling / www.etac.com
Notes
13
Molift RgoSling / www.etac.com
Etac A/S
Parallelvej 3
DK-8751 Gedved
www.etac.com
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
Molift RgoSling Ambulating Vest User manual
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Molift STRETCHER User manual
-
Molift Air 300 User manual
-
Molift Nomad User manual
-
Molift RgoSling Amputee HighBack User manual
-
Molift Mover 300 Electric Patient Lift User manual
-
Molift RgoSling MediumBack Net User manual
-
Molift Mover 180 User manual
-
Molift Mover 300 User manual
-
Molift Mover 300 User manual
-
Molift Air 500 User manual
Other documents
-
Etac BM40399 User manual
-
-
-
-
Classic Accessories 53112 Owner's manual
-
Hill-Rom Patient Lift Seated Slings Operating instructions
-
-
NRS Healthcare M07335 Operating instructions
-
Human Care 25120 Highback Plusline Sling User guide
-
