Marvel MPWC415 User manual

OWNERS GUIDE

MARVEL PROFESSIONAL UNDERCOUNTER REFRIGERATION

THE ORIGINAL REFRIGERATION EXPERTS SINCE 1892

FOR MODEL # MPWC415

Welcome to the Marvel Experience

Thank you for choosing our quality American-built product

to add to your home. We are thrilled to welcome you to

our growing community of Marvel owners, who trust in our

products and our support.

The information in this guide is intended to help you install

and maintain your new Marvel undercounter model to pro-

tect and prolong its lifetime. We encourage you to contact

our Technical Support team at (616) 754-5601 with any

questions.

Got a Marvelous Design?

We would love to see how your Marvel product looks in its

new home. Send us photos at marketing@marvelrefrigera-

tion.com, and we might feature your Marvel home design

on our website and social media!

Bonus Third-Year Warranty Free with Product

Registration

Your Marvel Professional product

qualies for a one-year extension

of the two-year warranty coverage

from your date of purchase, free of

charge. To take advantage of this

third-year warranty, be sure to reg-

ister your product with Marvel within

60 days from the date of purchase

at marvelrefrigeration.com and pro-

vide proof of purchase.

Thank you again for investing in Marvel for your home!

XXXXXXXXXXXX

MARVEL

g

Figure 1

R600A

WELCOME

It is important you send in your warranty registration card

immediately after taking delivery of your appliance or you

can register online at www.marvelrefrigeration.com.

The following information will

be required when registering

your appliance.

Service Number

Serial Number

Date of Purchase

Dealer’s name and address

The service number and serial number can be found on the

serial plate which is located inside the cabinet on the left

side near the top. See gure 1.

Warranty Registration

Online registra-

tion available at

www.marvelrefrig-

eration.com

TABLE OF CONTENTS

Tip: Click on any section below to jum

p directly there

Safety

Important Safety Instructions

Installation

Unpacking Your Appliance

Electrical

Cutout & Product Dimensions

Installing Your Appliance

Side-by-Side & Stacking Installations

Installing the anti-tip device

Door Reversal

Integrated Panel Dimensions

Integrated Panel Installation

Maintenance

Care and Cleaning

Extended Non-Use

Operating Instructions

Using Your Electronic Control

Shelving and Contents

Interior Adjustments

Energy Savng Tips

Service

Obtaining Service

Wire Diagram

Product Liability

Ordering Replacement Parts

R600a Specifications

System Diagnosis Guide

Compressor Specifications

Troubleshooting Extended

Control Operation - Service

Thermistor

Warranty

3

NOTE

!

CAUTION

Important Safety Instructions

Warnings and safety instructions appearing in this guide

are not meant to cover all possible conditions and situa-

tions that may occur. Common sense, caution, and care

must be exercised when installing, maintaining, or operat-

ing this appliance.

Recognize Safety Symbols,

Words, and Labels.

CAUTION-Hazards or unsafe practices which could re-

sult in personal injury or property / product damage.

NOTE-Important information to help assure a problem

free installation and operation.

!

WARNING

WARNING - You can be killed or seriously injured

if you do not follow these instructions.

!

WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known

to the State of California to cause cancer.

!

WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known

to the State of California to cause birth defects or

other reproductive harm.

!

WARNING

WARNING - This unit contains R600a (Isobutane)

which is a ammable hydrocarbon. It is safe for regular

use. Do not use sharp objects to expedite defrosting.

Do not damage refrigerant circuit.

IMPORTANT SAFETY INSTRUCTIONS

4

NOTE

!

CAUTION

!

WARNING

WARNING - Dispose of the plastic bags which can

be a suocation hazard.

!

WARNING

WARNING - Help Prevent Tragedies

Child entrapment and suocation are not problems of

the past. Junked or abandoned refrigerators are still

dangerous - even if they sit out for "just a few hours".

If you are getting rid of your old refrigerator, please fol-

low the instructions below to help prevent accidents.

Before you throw away your old refrigerator or freezer:

• Take o the doors or remove the drawers.

• Leave the shelves in place so children may not

easily climb inside.

!

WARNING

EXCESSIVE WEIGHT HAZARD

Use two or more people to move product.

Failure to do so can result in personal injury.

Remove Interior Packaging

Your appliance has been packed for shipment with all parts

that could be damaged by movement securely fastened.

Remove internal packing materials and any tape holding in-

ternal components in place. The owners manual is shipped

inside the product in a plastic bag along with the warranty

registration card, and other accessory items.

Important

Keep your carton and packaging until your appliance has

been thoroughly inspected and found to be in good condi-

tion. If there is damage, the packaging will be needed as

proof of damage in transit. Afterwards please dispose of all

items responsibly.

Note to Customer

This merchandise was carefully packed and thoroughly

inspected before leaving our plant. Responsibility for its

safe delivery was assumed by the retailer upon acceptance

of the shipment. Claims for loss or damage sustained in

transit must be made to the retailer.

DO NOT RETURN DAMAGED MERCHANDISE TO THE

MANUFACTURER - FILE THE CLAIM WITH THE

RETAILER.

If the appliance was shipped, handled, or stored in other

than an upright position for any period of time, allow the ap-

pliance to sit upright for a period of at least 24 hours before

plugging in. This will assure oil returns to the compressor.

Plugging the appliance in immediately may cause damage

to internal parts.

UNPACKING YOUR APPLIANCE

5

Electrical Connection

A grounded 115 volt, 15 amp dedicated circuit is required.

This product is factory equipped with a power supply

cord that has a three-pronged, grounded plug. It must be

plugged into a mating grounding type receptacle in accor-

dance with the National Electrical Code and applicable lo-

cal codes and ordinances (see Figure 4). If the circuit does

not have a grounding type receptacle, it is the responsibility

and obligation of the customer to provide the proper power

supply. The third ground prong should not, under any cir-

cumstances, be cut or removed.

Figure 4

NOTE

Ground Fault Circuit Interrupters (GFCI) are prone to nui-

sance tripping which will cause the appliance to shut down.

GFCI’s are generally not used on circuits with power equip-

ment that must run unattended for long periods of time, un-

less required to meet local building codes and ordinances.

ELECTRICAL

Figure 2

Do not remove

ground prong

Figure 3

Electrical Shock Hazard

• Do not use an extension cord with this appliance.

They can be hazardous and can degrade product

performance.

• This appliance should not, under any circumstanc-

es, be installed to an un-grounded electrical supply.

• Do not remove the grounding prong from the power

cord. (See Figure 2).

• Do not use an adapter. (See Figure 3).

• Do not splash or spray water from a hose on the

appliance. Doing so may cause an electrical shock,

which may result in severe injury or death.

!

WARNING

6

"C"

CUTOUT AND PRODUCT DIMENSIONS

"A"

"B"

"D"

"E"

Figure 5

(S) solid door

shown

Figure 5a

If necessary to gain clearance inside the rough-in

opening a hole can be cut through the adjacent cabi-

net and the power cord routed through this hole to a

power outlet. Another way to increase the available

opening depth is to recess the power outlet into the

rear wall to gain the thickness of the power cord plug.

Not all recessed outlet boxes will work for this applica-

tion as they are too narrow, but a recessed outlet box

equivalent to Arlington #DVFR1W is recommended for

this application, (see Figure 6).

Figure 6

ROUGH-IN OPENING DIMENSIONS CABINET DIMENSIONS

MODEL "A" "B" "C" "D" "E" "F" "G" "H" "J"

MPWC415-S*31A

15"

(38.1 cm)

34-1/4" - 35-1/4"

(87 to 89.5 cm)

24"

(61 cm)

14-7/8"

(37.8 cm)

33-5/8 - 34-5/8"

(85.4 to 88 cm)

23-5/8"

(60 cm)

25-3/8"

(64.5 cm)

38-3/4"

(98.4 cm)

17-1/2"

(44.5 cm)

MPWC415-I*31A

15"

(38.1 cm)

34-1/4" - 35-1/4"

(87 to 89.5 cm)

24"

(61 cm)

14-7/8"

(37.8 cm)

33-5/8 - 34-5/8"

(85.4 to 88 cm)

22-7/8"

(58.1 cm)

-

38-3/4"

(98.4 cm)

-

DOOR STYLE

(S) Solid Door

(I) Solid Integrated Door (no handle)

7

"D"

"E"

"F"

"G"

"H"

"J"

CUTOUT AND PRODUCT DIMENSIONS

PRODUCT DATA

MODEL

ELECTRICAL

REQUIREMENTS #

PRODUCT

WEIGHT

MPWC415 115V/60Hz/15A

105 lbs

(47.6 kg)

* To install (F) models with the door face ush with adja-

cent cabinetry doors, custom decorative panel thickness

cannot exceed

3

⁄4" (19 mm).

** Minimum rough-in opening required is to be larger than

the adjusted height of the cabinet.

# A grounded 15 amp dedicated circuit is required. Follow

all local building codes when installing electrical and appli-

ance.

3

1

⁄2" (8.9 cm)

Minimum

Figure 7

(S) solid door

shown

21

1

⁄2"

(54.6 cm)

8

!

CAUTION

Front grille

screws

Select Location

The proper location will ensure peak performance of your

appliance. We recommend a location where the unit will

be out of direct sunlight and away from heat sources. To

ensure your product performs to specications, the recom-

mended installation location temperature range is from 55

to 100°F (13 to 38°C).

Cabinet Clearance

Ventilation is required from the bottom front of the appli-

ance. Keep this area open and clear of any obstructions.

Adjacent cabinets and counter top can be installed around

the appliance as long as the front grille remains unobstruct-

ed. All Marvel Professional models with articulated hinges

are intended for built-in applications only.

Front Grille

Do not obstruct the front grille. The openings within the

front grille allow air to ow through the condenser heat ex-

changer. Restrictions to this air ow will result in increased

energy usage and loss of cooling capacity. For this reason

it is important this area to not be obstructed and the grille

openings kept clean. Marvel does not recommend the use

of a custom made grille as air ow may be restricted. (See

Figure 8).

INSTALLING YOUR APPLIANCE

!

WARNING

An optional stacking kit, for 24" wide models, is re-

quired to stack products. Failure to use a stacking kit

could result in personal injury. Contact your dealer or

Marvel customer service at 616-754-5601 to order.

For safety concerns 15" wide models should not be

stacked.

Figure 9

Front Leveling

Legs

Leveling Legs

Adjustable legs at the front and rear corners of the appli-

ance should be set so the unit is rmly positioned on the

oor and level from side to side and front to back. The over-

all height of your Marvel appliance may be adjusted higher

(by turning the leveling leg out, CCW) and lower (by turning

the leveling leg in, CW).

To adjust the leveling legs, place the appliance on a solid

surface and protect the oor beneath the legs to avoid

scratching the oor. With the assistance of another person,

lean the appliance back to access the front leveling legs.

Raise or lower the legs to the required dimension by turning

the legs. Repeat this process for the rear by tilting the appli-

ance forward using caution. On a level surface check the

appliance for levelness and adjust accordingly.

The front grille screws may be loosened and the grille ad-

justed to the desired height. When adjustment is complete

tighten the two front grille screws. (See Figure 9).

Rear

Leveling

Legs

Figure 8

Front grille, keep

this area open.

9

SIDE-BY-SIDE AND STACKING INSTALLATIONS

Side-by-Side Installation

Other Site Requirements

Units must operate from separate, properly grounded elec-

trical receptacles placed according to each unit's electrical

specications requirements.

Cutout width for a side-by-side installation is the total of the

widths listed under Cutout Dimensions in each unit's Instal-

lation Guide. Each door can be opened individually (one at

a time) without interference.

Figure 10

However, to ensure unobstructed door swing (opening both

doors at the same time), 1/4" (6.4 mm) of space needs to

be maintained between the units.

Hinge-by-Hinge Installation (Mullion)

When installing two units hinge-by-hinge, 13/16" (22 mm)

is required for integrated models. Additional space may be

needed for any knobs, pulls or handles installed.

Stainless steel models which include the standard stainless

handle will require 4-9/16" (116 mm) to allow both doors to

open to 90° at the same time.

Figure 11

Figure 12

Figure 13

10

INSTALLING THE ANTI TIP DEVICE

Step by step instructions for locating the po-

sition of the bracket:

1) Decide where you want to place the beverage center.



leaving 1" (2.5 cm) of clearance from the rear wall to allow

room for the anti-tip bracket.



¹

" (6 mm) to

allow engagement with the anti-tip bracket. Level the unit

by adjusting all the leveling legs as required. Turning the

leveling leg counterclockwise will raise the unit and clock-

wise will lower the unit.

3) Make sure the beverage center is in the desired loca-



cabinet where the anti-tip bracket will be installed. If the

installation does not allow marking the rear corner of the





beverage center out of the way. From the temporary line



1

2" (54.6 cm) as shown in

Figure 15.



the side of the bracket lines up with the side of the cabinet

mark, and the "V" notches on the anti-tip bracket line up

with the end of the 21

1

2" (54.6 cm) line (Rear of cabinet

line).



screw. (See Figure 15).

6) Slide the cabinet back into position, making sure the rear

cabinet leveling leg slides under the anti-tip bracket engag-

ing the slot.

Front of cabinet

Figure 14

21

1

2"

(54.6 cm)

Anti-Tip

Bracket

Leveling Leg

Bottom View of

Beverage

Center

Floor Mount Installation



or right rear corner of the wine cellar as shown in Figure 14.

!

WARNING

• ALL APPLIANCES CAN TIP

RESULTING IN INJURY.

• INSTALL THE ANTI-TIP

BRACKET PACKED WITH

THE APPLIANCE.

• FOLLOW THE INSTRUC-

TIONS BELOW

!

CAUTION

NOTE



material to avoid damage when moving the unit.



required, (not included with the anti-tip kit).

Anti-Tip Device

!

WARNING

If your beverage center is not located under a counter

top (free standing), you must use an anti-tip device

installed as per these instructions. If the beverage

center is removed from its location for any reason,

make sure that the device is properly engaged with

the anti-tip bracket when you push the beverage

center back into the original location. If the device is

not properly engaged, there is a risk of the beverage

center tipping over, with the potential for property dam-

age or personal injury.

11

NOTE

INSTALLING THE ANTI TIP DEVICE

-

mum adjusted height of the cabinet is increased by

3

8" (9 mm).

Figure 15a

"V" notches

in bracket

"V" notches

in bracket

Figure 15

21

1

2"

(54.6 cm)

Front of cabinet line

Rear Leveling leg

Side of cabinet line

Rear of cabinet line

Screw

12

Door Reversing Instructions

1. Open door.

2. Loosen screw #1 and #2 using a Philips Screwdriver on top and bottom hinge. Slide door and remove the door from the

unit.

3. Once door is removed, using a Philips Screwdriver remove screws from magnet actuator located on inside and bottom

of door. (On Integrated Models magnet actuator will be located on bottom of door.

Figure 16

Figure 17

Figure 18

4. Remove caps from top of door. Using a Philips Screwdriver, install magnet actuator on opposite side. Install caps into

opposite side.

5. Remove caps from screw holes on opposite side (2 on top and bottom). Using a Philips Screwdriver remove the 4

screws that you previously loosened.

6. Reinstall screws and caps on opposite side.

7. Once screws are partially installed, rotate the door 180°, align the hinge over screw #1 and slide into position. Tighten

screws on top and bottom.

8. Door is now reversed.

DOOR REVERSAL

"V" notches

in bracket

13

1

5

⁄32"

(2.9 cm)

Hinge side of door

Top of door

INTEGRATED PANEL DIMENSIONS

Figure 21

Right Hand Hinged Door

15" (38.1 cm) wide appliance

Figure 22

Right Hand Hinged Door

15" (38.1 cm) wide appliance

Clearance

for hinge

at top and

bottom

Hinge side of door

Top of door

Figure 20

Left Hand Hinged Door

15" (38.1 cm) wide appliance

Figure 19

Left Hand Hinged Door

15" (38.1 cm) wide appliance

Clearance

for hinge

at top and

bottom

14

INTEGRATED DOOR PANEL INSTALLATION

!

CAUTION

Integrated door panel installation:

Step 1: Removing the Door

Open the door and loosen the screws holding the hinges to

the cabinet (2 at the top and 2 at the bottom hinge). Do not

remove the screws but loosen them enough so the hinges



the side.

With a helper, and being careful not to scratch the cabinet

or the door, slide the door to the side about

1

2 inch and

remove the hinges and door from the unit.

!

WARNING

Integrated panel models are designed for use with

built-in installations only. Use in freestanding instal-

lations could result in personal injury.

If you purchased an integrated panel model, your unit is

equipped with articulated hinges to allow fully integrated

built-in installations. Custom panel thicknesses of

5

8" (15

mm) and

3

4" (18 mm) are accommodated.

It is important to use the factory provided grille that came



through the condenser. The use of a custom grille is not

recommended and will void the warranty.

!

WARNING

The articulated hinges have many pinch points. Care-

fully close / collapse the hinges as soon as the door is

removed from the cabinet.

15

INTEGRATED DOOR PANEL INSTALLATION

Integrated



with top and

side of door.

Magnetic Gasket

remove starting at a

corner, grasp and pull

away from the door.

Step 3: Cut and drill the integrated panel

Depending on your model cut the integrated door panel to

the dimensions shown in Figures 19 to 22. The window cut

out is for glass door models only. If your appliance has a

lock also drill the lock hole in the panel, see Figure 25.

Integrated panel

to be centered

on width of door.

Figure 24

Holes in

gasket

retainer.

Figure 24a

Step 2: Remove the door gasket



corner of the door remove the magnetic door gasket from

the interior side of the door, see Figure 25. Set the gasket





each side and 2 at the top and bottom which are used to

fasten the panel to the front of the door. The screws are

provided in the literature pack along with the door lock,

which is provided on certain models.

Loosen (do not remove ) these

2 phillips head screws on the

top and bottom hinges

!

WARNING





to built-in installation. Do not remove the cabinet "Z"

bracket from the top of the cabinet.

Figure 23b

Bottom of

door

"P" clamp

and screw

Wire connector

see Figure 6

Figure 23

Figure 23a

Cabinet

"Z" Bracket

16

!

CAUTION

INTEGRATED DOOR PANEL INSTALLATION

Material Type #10 Wood Screw

Hardwood

¹

" (3.2 mm) Diameter. Pilot Hole

Softwood



 (2.8 mm) Diameter. Pilot Hole

Table A

Weight of integrated door panel must not exceed 15

pounds (6.8 kg) for a solid door model or 10 pounds

(4.5 kg) for a glass door model.



1

2"

screw

Step 4: Assemble the panel to the door

The preferred method of attaching the panel to the door

is to clamp the panel to the door so it cannot move while

drilling the screw pilot holes. Use bar clamps or "C" clamps

with pads on the clamping surfaces that will not mar the

panel or the door. The custom integrated panel should be



of the door. See Figure 24a. Drill holes through the gasket



size from the chart in Table "A", being careful not to drill

through the front surface of the panel. If the integrated

panel is thinner than

5

8" (16 mm) thick shorter screws will

have to be obtained. Fasten the panel to the door with

the 10 screws provided in the literature pack. (See Figure

25a). Remove the clamps and replace the gasket in the



required to seat the gasket into the channels. Be sure the

gasket corners are seated properly.

A A

B B

C C

D D

8

7

6

5

4

3

2

1

PANEL-WOOD

DO NOT SCALE DRAWING

24 Panel

SHEET 1 OF 1

UNLESS OTHERWISE SPECIFIED:

SCALE: 1:5

WEIGHT:

REV

DWG. NO.

D

SIZE

TITLE:

NAME

DATE

COMMENTS:

Q.A.

MFG APPR.

ENG APPR.

CHECKED

DRAWN

FINISH

MATERIAL

INTERPRET GEOMETRIC

TOLERANCING PER:

DIMENSIONS ARE IN INCHES

TOLERANCES:

FRACTIONAL

ANGULAR: MACH

BEND

TWO PLACE DECIMAL

THREE PLACE DECIMAL

APPLICATION

USED ON

NEXT ASSY

PROPRIETARY AND CONFIDENTIAL

THE INFORMATION CONTAINED IN THIS

DRAWING IS THE SOLE PROPERTY OF

<INSERT COMPANY NAME HERE>. ANY

REPRODUCTION IN PART OR AS A WHOLE

WITHOUT THE WRITTEN PERMISSION OF

<INSERT COMPANY NAME HERE> IS

PROHIBITED.

Counter bore

lock hole

on back side.

Figure 25 - Back of Panel

1

2" (13 mm)

diameter drill through

door panel, from other

side

13

16" (20.5 mm)

counter bore,

7

16" (11

mm) deep.

Hinge side of door

Figure 25a

17

Cabinet

"Z" bracket



3

4" black

screws

(3 places)

Figure 28

Step 7: Install the door

Carefully open the top and bottom hinges on the door being

careful as there are many pinch points. Place the hinges

over the 4 screws in the cabinet, 2 at the top and 2 at the

bottom and slide the door into position. Tighten the 4 hinge

screws with a phillips screwdriver. (See Figures 15 and

15a).

SECTION A-A

SCALE 1 : 1

LOCK

NUT

BRASS EXTENSION

CAM

PHILLIPS SCREW

13/16 COUNTER

BORE 7/16 DEEP

1/2 HOLE

3/4 INCH

WOOD PANEL

SPRING WASHER

INNER

DOOR

Step 8: Secure the cabinet



3

4" black screws from the literature pack to

secure the counter top to the cabinet top through the holes

in the cabinet "Z" bracket.

INTEGRATED DOOR PANEL INSTALLATION

Figure 27

Step 6: Install lock cam

Attach the lock cam to the back of the lock assembly with

the phillips head screw provided. Orient the lock cam verti-

cally when installing on the lock.

Cam stop

washer

Spring

washer

Cam

Set screw

Lock

Key

Retainer

nut

Screw

Brass



(2 lengths

provided)

Step 5: Assemble lock parts





3

4" thick integrated panels and the

shorter one for

5

8" thick integrated panels. Assemble the



screw to the lock as shown in Figure 26 and 27.

Install this lock assembly into the lock hole in the integrated

panel and secure with the retaining nut on the back side

with a 15 mm socket and ratchet. Make sure the key slot in

the front of the lock is vertical.

Figure 26

18

USING YOUR ELECTRONIC CONTROL

Control Function Guide

Function Command Notes

ON/OFF Press and release. Unit will immediately turn ON or OFF.

Adjust Temperature Press or and release.

When the display is ashing, press or to adjust the set

point temperature. Note: temperature displayed is the actual

temperature inside unit.

Toggle Between

o

F /

o

C Hold and for 5 seconds. The display will change units.

Leave Interior Light On

Press and release to leave interior light on for

12 hours; press again to deactivate.

After 12 hours, factory default is restored; light will turn on when

door is open.

Hide Display Hold and press .

Display will turn o when door is closed. Unit will continue to

operate. Repeat command to turn on display.

Adjust Light Color

Press and hold then press and wait for

UI to ash. Once UI ashes, release and ,

and use the to scroll through options 0-2.

Option Open Door Closed Door

White White

Blue Blue

White Blue

Light will be set at full intensity when door is open, and 50%

intensity when door is closed.

Enable Sabbath Mode Press and hold for 5 seconds and release.

The

o

F /

o

C symbol will ash briey after 5 seconds. Interior

light and display will go dark and remain so until user resets

mode - unit continues to operate.

Disable Sabbath Mode Press and release. Display and interior light return to normal operation.

Showroom Mode Hold and for 5 seconds.

The

o

F /

o

C symbol will ash. Display will be lit and interior light

will function. Unit will not cool. Repeat command to return to

normal operation.

Door Alert Notication

When the door is left open for more than 30 minutes:

• A tone will sound for several seconds every minute

• will appear in display

• Close door to silence alert and reset

First Use

Initial startup requires no adjustments. When plugged in, the unit will

begin operating under the factory default settings. If the unit was turned o

during installation, simply press and the unit will immediately switch on.

To turn the unit o, press .

Temperature displayed reects actual temperature inside unit. If the

temperature displayed is dierent than selected, the unit is progressing

towards the selected temperature. Time to reach set point varies based

upon ambient temperature, temperature of product loaded, door openings,

etc. Marvel recommends allowing the unit to reach set points before

loading.

NOTE

Figure 29

Electronic control

19

SHELVING AND CONTENTS

Shelving Congurations

Your Marvel Professional Series appliance is equipped with

full extension ball bearing shelf glides to provide maximum

access and visibility for the product stored on the shelving

arrangements listed below.

Dual Zone Wine Cellar:

24" (61 cm) Wide models:

Upper Zone: (3) 8 bottle wire racks

Lower Zone: (1) 8 bottle wire rack

(2) 4 bottle half-depth wire racks

Single Zone Wine Cellar:

24" (61 cm) Wide models:

(5) 8 bottle wire racks

(2) 4 bottle half-depth wire racks

Single Zone Wine Cellar:

15" (38.1 cm) Wide models:

(6) 4 bottle wire racks

Figure 30

Figure 32

Figure 31

20

Page is loading ...

Marvel MPWC415, MPWC415-IS31A, undefined User manual

Related papers

Other documents