2. Computers & electronics
  3. Computer components
  4. Chassis components
  5. Computer cases
  6. Sharkoon
  7. Rebel9 Pro Window

Sharkoon Rebel9 Pro Window Specification

  • Hello! I am an AI chatbot trained to assist you with the Sharkoon Rebel9 Pro Window Specification. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Handbuch
Manual
REBEL9 PRO (EcOnOmy, vaLuE and windOw)
Content
1. Features
2. Package content
3. The case at a glance
4. Installation of a mainboard
5. Installation of a PSU
6. Installation of a HDD
7. Installation of an optical device
8. Installation of a 3.5" device
9. Installation of an add-on card
10. The pre-installed fans (Value and Window Edition only)
11. Installation of additional fans / optimized airflow
Dear customer!
Congratulations for purchasing one premium quality SHARKOON product.
For a long life time and to take full advantage of this product we recommend that you read
this manual completely.
Have a good time with our product!
SHARKOON Technologies
REBEL9 PRO (EcOnOmy, vaLuE and windOw)
1. Features
• ATXcase
• 9x5.25"drivebays(6xexternal)
• TopI/O(EconomyandValue):2xUSB2.0,1xeSATA,2xaudioconnectors,powerand
resetbutton
• TopI/O(Window):1xUSB3.0,2xUSB2.0,2xaudioconnectors,powerandresetbutton
• 7slotsforadd-oncards
• Plasticfrontpanelwithairinlet,drivebaycoversinmeshdesign
• Quick fasteners for optical drives, mainboard mounting with installation opening for
coolers
• 2openingsforwatercooling
• Cablemanagementsystem
• Fanconguration:
Economy Edition Value Edition Window Edition
Case front 1x120mmfan(optional)
1x120mmfanwithLEDaswell
as3-pinand4-pinconnector
(pre-installed)
1x120mmfanwithLEDaswell
as3-pinand4-pinconnector
(pre-installed)
Side panel 2x120mmfan(optional)
1x250mmfanwithLED,
rpmcontrollerand4-pincon-
nector(pre-installed)
Acrylic
Backside
1x80mmor1x120mmfan
(optional)
1x120mmfan(pre-installed)
1x120mmfanwithLEDaswell
as3-pinand4-pinconnector
(pre-installed)
Toppanel
1x120mmor1x140mmfan
(optional)
1x120mmor1x140mmfan
(optional)
1x120mmor1x140mmfan
(optional)
• Dimensions:455x202x440mm(LxWxH)
• Weight:~6kg
2. Package content
• Rebel9ProEconomyorValueorWindowEdition
• Screwkit:
Screwsformainboard
mounting
ScrewsforPSU
mounting
Screws for drive moun-
ting(3.5"and5.25")
Screws for HDD mounting
REBEL9 PRO (EcOnOmy, vaLuE and windOw)
• Accessorykit:
Stand-offsformainboard Washers Lockattachment(A)andspeaker(B)
MountinganglesforHDDs(withdecoupling/A)and3.5"devices
(notdecoupled/B)
QuickfastenersforODDs 5.25"bezelwith3.5"opening
Note:
If you are missing any of the items listed above, please contact our customer service
immediately:
suppor[email protected] (Germany and Europe)
suppor[email protected] (international).
REBEL9 PRO (EcOnOmy, vaLuE and windOw)
3. The case at a glance
Front view
A – LEDforHDDactivity
B– 5.25"drivebays
C– behindthemeshbezel:
pre-installed120mmfan(ValueandWindowEdition)
Viewfromabove
Frontpanel:
A– Powerand
B– Resetbutton
Casetop:
C– TopI/Owith:
a– 1x headphone and microphone
connector
b– 2xUSB2.0and
c – 1x eSATA (Economy and Value
Edition) / USB3.0 (Window Edition)
connector
D– Fanbracket
Sideview(closed/left,Economy)
A–Fanbrackets(120mm)
a
b
c
A
A
A
B
B
C
C
D
REBEL9 PRO (EcOnOmy, vaLuE and windOw)
Sideview(closed/left)
ValueEdition:
A– Pre-installed,adjustable
250mmfan
WindowEdition:
A – Acrylic window
Sideview(opened/left)
A– Drivebaysfor5.25"devices
B– Mainboardmountingpanelwith:
a– Installation opening for CPU
coolers and
b– Cablemanagementsystem
Backside
A– OpeningforI/Oshield
B– Fanbracket(Economy)orpre-installed 120mmfan
(ValueandWindowEdition)
C– Slotbezels
D – Openings for water cooling
E– PSUbracket
F– Thumbscrews
a
b
A
A
A A
B
B
C
D
E
F
F
F
F
REBEL9 PRO (EcOnOmy, vaLuE and windOw)
Bottomview
A – Case feet
B– AirintakeforPSU
Note:
For more information on how to install the intended devices, refer to their respective
documents.
4. Installation of a mainboard
1.Openthecasebylooseningthethumbscrewsonthecase’sbacksideandremovingtheleft
sidepanel.Laydownthecasesidewiseonanevensurface.
2.The mainboard’s mounting panel inside the case provides various drillings to x the
stand-offs(g.1).
g.1
Themainboardcontainsspecialscrewopenings(g.2).
 g.2
A A
AA
B
REBEL9 PRO (EcOnOmy, vaLuE and windOw)
Placethemainboardtothemountingpanel.Astand-offmustbescrewedintoeverydrilling
ofthemountingpanelvisiblethroughthemainboard’sscrewopenings.
3.Remove the mainboard and screw the stand-offs into the respective drillings of the
mountingpanel(g.3).
(Stand-offs)
Fig.3
4.PresstheI/Oshield(deliveredwiththemainboard)intotheI/Oshieldopeninginthecase’s
backside.
5.Placethemainboardbackontothestand-offsandscrewthemainboardtothem(g.4).
(Screwsformainboardmounting)
g.4
REBEL9 PRO (EcOnOmy, vaLuE and windOw)
6.Plugtheconnectorsofthecase’sfrontbezeltotherespectiveconnectorsofthemainboard
(alsorefertoyourmainboard’smanualforfurtherinformation).
Note (Value and Window edition only):
The eSATA cable connected to the front eSATA connection should not exceed 50 cm of
length otherwise transmission errors may occur! With premium quality eSATA cables this
maximum length may be exceeded.
5. Installation of a PSU
1.SetupthecaseinfrontofyouandputthePSUfromtheinsideagainstthePSUbracketon
thecase’sbackside(g.5).
g.5
2.ScrewthePSUtothecasefromtheoutside(g.6).
(ScrewsforPSUmounting)
g.6
REBEL9 PRO (EcOnOmy, vaLuE and windOw)
6. Installation of a HDD
1.Removethecase’srightsidepanel.
2.AttachthedecoupledmountinganglestotheHDDfrombothsides(g.7).
(ScrewsforHDDmounting)
(Decoupledmountingangles)
g.7
3. Slide the HDD with attached mounting angles into the case’s respective drive bay and
screwitfrombothsides(g.8).
 g.8
4.ConnecttheHDDtothepowersupplyandthemainboard.
REBEL9 PRO (EcOnOmy, vaLuE and windOw)
7. Installation of an optical device
1.Removethecase’sfrontpanelbygentlydraggingittowardsyou(g.9).
g.9
2.Dismantlethe5.25"frontbezelfromthemountingbayinwhichyouintendtoinstallthe
drivebylooseningitsscrewsandpushingthebezeltotheinside(g.10).Removethequick
fasteners(g.11).
g.10g.11
(Carefullytakeoutanoptionallypresentmetalbezelcoveringthe3.5"drivebaybyusinga
gripper.)
3.Slidetheopticaldriveintothecase’sdrivebay(g.12).
g.12
REBEL9 PRO (EcOnOmy, vaLuE and windOw)
4.Attachtheopticaldevicefrombothsidesusingthequickfasteners(g.13).
 g.13
Note:
If you intend to transport the case we recommend securing (additionally) the installed
drives:
Screwsfor5.25"drivemounting
5.Connecttheopticaldrivetothepowersupplyandthemainboard.(Putthefrontbezelback
ontothecase.)
8. Installation of a 3.5" device
(1.Removethecase’sfrontpanelbygentlydraggingittowardsyou.)
2.Dismantlethe5.25"frontbezelfromthemountingbayinwhichyouintendtoinstallthe
drivebylooseningitsscrewsandpushingthebezeltotheinside(g.14).Removethequick
fasteners(g.15).
g.14g.15
(Carefully take out an optionally present metal bezel covering the drive bay by using a
gripper.)
REBEL9 PRO (EcOnOmy, vaLuE and windOw)
3.Screwthemountinganglestothe3.5"devicefrombothsides(g.16).
g.16
4.Slidethe 3.5"devicewithattachedmountingrailsintothecase’sdrivebay(g. 17)and
screwittothedrivebayfrombothsides(g.18).
g.17g.18
5.Connectthe3.5"devicetothepowersupplyandthemainboard.
6.Screwthe5.25"bezelwith3.5"openingintothefrontpanel(g.19)andplaceitbackonto
the case.
5.25"bezelwith3.5"opening
g.19
REBEL9 PRO (EcOnOmy, vaLuE and windOw)
9. Installation of an add-on card
1.Removetheslotbezel’sxationscrewandtakeawaytheslotbezel(g.21).
g.21
2.Insert the add-on card into the mainboard’s respective slot and x it to the case by
re-attachingthexationscrew(g.22).
g.22
10. The pre-installed fans (Value and Window Edition only)
1.Thepre-installed120mmfansprovidea4-pinPSUconnectoranda3-pinmainboardplug
each.
2.ConnectoneofbothplugstoeithertherespectivePSUor(tocontrolthefanspeedviathe
mainboard)thematchingmainboardconnector.
REBEL9 PRO (EcOnOmy, vaLuE and windOw)
11. Installation of additional fans / optimized airflow
1.Placethefanagainsttherespectivebracketfromtheinside(e.g.inthetoppanel/g.23).
 g.23
2.Screwthefantotheattachmentfromtheoutside(g.24).
g.24
Note:
The Rebel 9 Pro case offers a lot of possibilities to install fans.
While installing fans make sure that (cool) air is taken in on the case’s front side/bottom and
blown out on its back side/top. The PC components with the highest heat development
should be placed directly within the airflow.
REBEL9 PRO (EcOnOmy, vaLuE and windOw)
Legal disclaimer:
AsacontinuingpolicyofproductimprovementatSHARKOON,thedesignandspecications
aresubjecttochangewithoutpriornotice.Nationalproductspecicationsmayvary.
All rights reserved especially (also in extracts) for translation, reprinting, reproduction by
copyingorothertechnicalmeans.Infringementswillleadtocompensation.
All rights reserved especially in case of assignation of patent or utility patent. Means of
deliveryandtechnicalmodicationsreserved.
Disposal of your old product
Your product is designed and manufactured with high quality materials and components,
whichcanberecycledandreused.
Whenthiscrossed-outwheeledbinsymbolisattachedtoaproduct,itmeanstheproductis
coveredbytheEuropeanDirective2002/96/EC.
Pleasebe informedabout thelocalseparatecollectionsystem forelectrical andelectronic
products.
Pleaseactaccordingtoyourlocalrulesanddonotdisposeofyouroldproductswithyour
normalhouseholdwaste.Thecorrectdisposalofyouroldproductwillhelppreventpotential
negative consequences to the environment and human health.
© SHARKOON Technologies 2011
www.sharkoon.com
/