Middleby Marshall PS724E User manual

Brand: Middleby Marshall

Model: PS724E

Category: Ovens

Type: User manual

This manual is also suitable for

MiddlebyMiddleby

Middleby

MarshallMarshall

Marshall

A MIDDLEBY COMPANY

PS724-Series Electric Ovens: English

October 27, 2008

owner's

operating

& installation

manual

PS724-Series

OVENS

Model

PS724E

PS724 (Triple)

PS724 (Double)

Part No. 61778

Price $30.00

P: 10/08

PS724 (Single)

WARNING

FOR YOUR SAFETY, DO NOT STORE OR USE

GASOLINE OR OTHER FLAMMABLE VAPORS AND

LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER

APPLIANCE.

WARNING

Improper installation, adjustment, alteration, service, or

maintenance can cause property damage, injury, or

death. Read the installation, operation, and maintenance

instructions thoroughly before installing or servicing this

equipment.

NOTICE

The warranty is

NOT VALID

unless the oven is installed, started, and

demonstrated under the supervision of a factory-authorized installer.

NOTICE

Contact your authorized Service Agency to perform maintenance and

repairs. A Service Agency Directory is supplied with your oven.

NOTICE

Using any parts other than genuine Middleby Marshall factory-manufactured

parts relieves the manufacturer of all warranty and liability.

NOTICE

Middleby Marshall (Manufacturer) reserves the right to

change specifications at any time.

KEEP THIS MANUAL IN A VISIBLE LOCATION NEAR THE OVEN

FOR FUTURE REFERENCE.

NOTICE:

This

Owner's Operating and Installation Manual should be given to the user. The operator of the oven should

be familiar with the functions and operation of the oven.

This manual must be kept in a prominent, easily reachable location near the oven.

It is suggested to obtain a service contract with a Middleby Marshall Authorized Service Agent.

iii

MIDDLEBY MARSHALL INC.

OVEN LIMITED WARRANTY

(Non U.S.A.)

The Seller warrants equipment manufactured by it to be free from

defects in material and workmanship for which it is responsible. The

Seller’s obligation under this warranty shall be limited to replacing or

repairing, at Seller’s option, without charge, F.O.B. Seller’s factory,

any part found to be defective and any labor and material expense

incurred by Seller in repairing or replacing such part. Such warranty

is limited to a period of one year from date of original installation or

15 months from date of shipment from Seller’s factory, whichever is

earlier, provided that terms of payment have been fully met. All labor

shall be performed during regular working hours. Overtime premium

will be charged to the Buyer.

This warranty is not valid unless equipment is installed, started,

and demonstrated under the supervision of a factory-autho-

rized installer.

Normal maintenance functions, including lubrication, adjustment of

airflow, thermostats, door mechanisms, microswitches, burners

and pilot burners, and replacement of light bulbs, fuses and indicat-

ing lights, are not covered by warranty.

Any repairs or replacements of defective parts shall be performed by

Seller’s authorized service personnel. Seller shall not be respon-

sible for any costs incurred if the work is performed by other than

Seller’s authorized service personnel.

When returning any part under warranty, the part must be intact and

complete, without evidence of misuse or abuse, freight prepaid.

Seller shall not be liable for consequential damages of any kind

which occur during the course of installation of equipment, or which

result from the use or misuse by Buyer, its employees or others of

the equipment supplied hereunder, and Buyer’s sole and exclusive

remedy against Seller for any breach of the foregoing warranty or

otherwise shall be for the repair or replacement of the equipment or

parts thereof affected by such breach.

The foregoing warranty shall be valid and binding upon Seller if and

only if Buyer loads, operates and maintains the equipment supplied

hereunder in accordance with the instruction manual provided to

Buyer. Seller does not guarantee the process of manufacture by

Buyer or the quality of product to be produced by the equipment

supplied hereunder and Seller shall not be liable for any prospective

or lost profits of Buyer.

THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF

ALL OTHER EXPRESS AND IMPLIED WARRANTIES WHATSO-

EVER. SPECIFICALLY THERE ARE NO IMPLIED WARRANTIES

OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR

PURPOSE.

The foregoing shall be Seller’s sole and exclusive obligation and

Buyer’s sole and exclusive remedy for any action, whether in breach

of contract or negligence. In no event shall seller be liable for a sum

in excess of the purchase price of the item.

Model No.

Modéle No.

Serial No.

Serié No.

Installation Date

Date d'installation

MIDDLEBY MARSHALL

NO QUIBBLE LIMITED WARRANTY

(U.S.A. ONLY)

MIDDLEBY MARSHALL, HEREINAFTER REFERRED TO AS

“THE SELLER”, WARRANTS EQUIPMENT MANUFACTURED

BY IT TO BE FREE FROM DEFECTS IN MATERIAL AND

WORKMANSHIP FOR WHICH IT IS RESPONSIBLE. THE

SELLER’S OBLIGATION UNDER THIS WARRANTY SHALL

BE LIMITED TO REPLACING OR REPAIRING, AT SELLER’S

OPTION, WITHOUT CHARGE, ANY PART FOUND TO BE

DEFECTIVE AND ANY LABOR AND MATERIAL EXPENSE

INCURRED BY SELLER IN REPAIRING OR REPLACING

SUCH PART. SUCH WARRANTY SHALL BE LIMITED TO

THE ORIGINAL PURCHASER ONLY AND SHALL BE EFFEC-

TIVE FOR A PERIOD OF ONE YEAR FROM DATE OF ORIGI-

NAL INSTALLATION, OR 18 MONTHS FROM DATE OF PUR-

CHASE, WHICHEVER IS EARLIER, PROVIDED THAT TERMS

OF PAYMENT HAVE BEEN FULLY MET.

This warranty is valid only if the equipment is installed, started,

and demonstrated under the supervision of a factory-autho-

rized installer.

Normal maintenance functions, including lubrication, clean-

ing, or customer abuse, are not covered by this

no quibble

warranty

Seller shall be responsible only for repairs or replacements

of defective parts performed by Seller’s authorized service

personnel. Authorized service agencies are located in prin-

cipal cities throughout the contiguous United States, Alaska,

and Hawaii. This warranty is valid in the 50 United States

and is void elsewhere unless the product is purchased

through Middleby International with warranty included.

The foregoing warranty is exclusive and in lieu of all other

warranties, expressed or implied. There are no implied

warranties of merchantability or of fitness for a particu-

lar purpose.

The foregoing shall be Seller’s sole and exclusive obligation

and Buyer’s sole and exclusive remedy for any action, in-

cluding breach of contract or negligence. In no event shall

Seller be liable for a sum in excess of the purchase price of

the item. Seller shall not be liable for any prospective or lost

profits of Buyer.

This warranty is effective on Middleby Marshall equip-

ment sold on, or after, February 15, 1995.

The Middleby Marshall logo is a registered trademark of Middleby Marshall, A Middleby Company.

Middleby Marshall Inc. • 1400 Toastmaster Drive • Elgin, Illinois 60120-9272 U.S.A. • (847) 741-3300 • FAX: (847) 741 4406

NOTE

Wiring Diagrams are in Section 6 of this Manual.

The diagram for each oven is also inside the left

side control box door.

TABLE OF CONTENTS

Page

SECTION 1

I. MODEL IDENTIFICATION .............................................. 1

SERIES PS724 ELECTRIC SPECIFICATIONS ................. 2

II. COMPONENT FUNCTION ............................................. 4

A. Conveyor Motor and Conveyor Belt ........................ 4

B. Blower Fan ................................................................. 4

C. Cooling Fan ................................................................ 4

D. Air Fingers and Blank Plates - See Figure 1-9 ........ 4

SECTION 2

I. UNLOADING ................................................................... 8

PARTS LIST FOR SERIES PS724 ELECTRIC OVEN

INSTALLATION KIT .................................................... 8

UTILITY ROUGH-IN DIMENSIONS AND POSITIONING

FOR PS724-SERIES OVENS .................................... 13

CIRCUIT BREAKER ..................................................... 13

ELECTRICAL SPECIFICATIONS ................................. 13

ELECTRICAL RATING ................................................. 13

SUPPLY WIRE .............................................................. 13

SUGGESTED ................................................................ 13

II. VENTILATION GUIDELINES ........................................ 13

III. ELECTRICAL CONNECTION INFORMATION FOR

PS724-SERIES OVENS. ........................................... 14

IV. ELECTRIC SUPPLY .................................................... 14

SECTION 3 INSTALLATION

I. CONTROL FUNCTIONS ................................................ 15

II. COMPONENT INFORMATION AND LOCATION ......... 16

A. Door Safety Switch .................................................. 16

B. Blower Switch .......................................................... 16

C. Heat Switch .............................................................. 16

D. Temperature Controller .......................................... 16

E. Conveyor ................................................................. 17

MEASURING CONVEYOR SPEED. ............................. 17

TABLE OF CONTENTS

(Continued)

Page

III. STEP-BY-STEP OPERATION ..................................... 18

A. Startup Procedures ................................................. 18

Daily Startup ................................................................. 18

Power Failure ............................................................... 18

B. Shutdown Procedure ............................................... 18

IV. NORMAL OPERATION - STEP-BY-STEP ................... 20

A.Daily Startup Procedure ........................................... 20

B. Daily Shutdown Procedure ...................................... 20

V. QUICK REFERENCE: TROUBLESHOOTING ............ 22

SECTION 4 MAINTENANCE

I. MAINTENANCE - DAILY ............................................ 24

A. Exterior ..................................................................... 24

B. Cooling Fan ............................................................. 24

C. Conveyor Belt .......................................................... 24

D. Crumb Pans ............................................................. 24

II. MAINTENANCE - MONTHLY ....................................... 25

A. Removing Conveyor From Oven For Cleaning ..... 25

B. Air Fingers Disassembly For Cleaning .................. 27

C. Reassembly of Air Fingers ..................................... 28

D. Reinstall End Plugs ................................................. 30

E. Conveyor Reassembly Into Oven .......................... 31

F. Checking Conveyor Belt Tension ........................... 31

G. Conveyor Belt Link Removal ................................. 32

H. Attaching Drive Chain ............................................. 33

III. MAINTENANCE - (3 and 6 MONTH) ............................ 34

PS724-SERIES ELECTRIC OVEN KEY

SPARE PARTS ........................................................... 35

KEY SPARE PARTS KIT ............................................... 35

SECTION 5 TROUBLESHOOTING

Troubleshooting Charts ...................................................... 37

SECTION 6 ELECTRICAL SCHEMATICS

Wiring Diagrams ............................................................... 39

SECTION 1

DESCRIPTION

I. MODEL IDENTIFICATION

The Middleby Marshall PS724-Series may be used

either as a single oven or stacked for use as double or

triple ovens.

A single PS724-Series Oven (Figure 1-1) can be mounted

on an insulated base with short legs for countertop use,

or on a leg stand with a lower shelf and casters for a free

standing unit. A double oven (Figure 1-2) consists of

two,

stacked,

single ovens. A triple oven (Figure 1-3)

consists of three stacked single ovens. The lower oven

is mounted on an insulated base with casters affixed.

On a double or triple oven, the ovens operate indepen-

dently. All ovens use identical controls and compo-

nents. One oven can be cleaned or serviced, while the

others are operating.

SECTION 1

DESCRIPTION

Figure 1-1. Single PS724 Oven

Figure 1-2. Double PS724 Oven

Figure 1-3. Triple PS724 Oven

SECTION 1

DESCRIPTION

NOTE

Wiring Diagrams are contained in Section 6 of this Manual

and are also located inside inside the left side control box door.

Additional electrical information is provided on the oven's serial plate.

This Manual Must Be Kept For Future Reference.

PS724 SERIES OVEN SPECIFICATIONS

Conveyor Belt Width 18.00″ (457 mm)

Heating Zone Length 24.00″ (610 mm)

Baking Area Square Feet 3.0 sq. ft. (0.28 m

)

Overall Dimension – Standard Single Oven w/Legs - 8″ Exit tray Installed 64.00″ (1625 mm) L ×

36.00″ (914 mm) W ×

43.69″ (1110 mm) H ×

Overall Dimension – Double Oven 64.00″ (1625 mm) L ×

36.00″ (914 mm) W ×

64.00″ (1625 mm) H ×

Overall Dimension – Triple Oven 64.00″ (1626 mm) L ×

36.00″ (914 mm) W ×

69.25″ (1759 mm) H ×

Weight of Single Oven 250 lb (93.3 kg)

Shipping Weight 360 lb (163.3 kg)

Shipping Cube 61.1 ft

(1.73 m

)

Operating Range 17.4 kW/hr

Maximum Operating Temperature 600°F (316°C)

Warm-up Time 20 min.

Belt Speed Limits 0.30 - 12:00

SERIES PS724 ELECTRICAL SPECIFICATIONS

DOMESTIC OVENS

VOLTAGE PHASE HZ kW WIRING BREAKER POWER POWER

SIZE CORD PLUG

SPECIFICATION

208 3 60 14.4 STD 4-WIRE / L1,L2,L3 & GROUND 50 A 8 GA, 4-WIRE NEMA 15-50P

3 50-60 17.4 OPT 4-WIRE / L1,L2,L3 & GROUND 60 A 6 GA, 4-WIRE NEMA 15-60P

240 3 60 14.4 STD 4-WIRE / L1,L2,L3 & GROUND 50 A 8 GA, 4-WIRE NEMA 15-50P

3 60 17.4 OPT 4-WIRE / L1,L2,L3 & GROUND 60 A 6 GA, 4-WIRE NS

480 3 60 17.4 STD 5-WIRE / L1,L2,L3,N & GROUND 30 A 8 GA, 5-WIRE NS

INTERNATIONAL OVENS

VOLTAGE PHASE HZ kW WIRING BREAKER POWER POWER

SIZE CORD PLUG

SPECIFICATION

208 3 50-60 17.4 OPT 4-WIRE / L1,L2,L3 & GROUND 60 A 6 GA, 4-WIRE - NS NS

3 50-60 14.4 STD 4-WIRE / L1,L2,L3 & GROUND 50 A 8 GA, 4-WIRE - NS NS

230-240 3 50-60 16 / 17.4 OPT 4-WIRE / L1,L2,L3 & GROUND 60 A 6 GA, 4-WIRE - NS NS

3 50-60 13.2 / 14.4 STD 4-WIRE / L1,L2,L3 & GROUND 50 A 8 GA, 4-WIRE - NS NS

380 3 50-60 17.4 STD 5-WIRE / L1,L2,L3,N & GROUND 40 A 10 GA, 4-WIRE - NS NS

400-416 3 50-60 16.1 / 17.4 STD 5-WIRE / L1,L2,L3,N & GROUND 35 A 6 GA, 5-WIRE - NS NS

STD = Standard

OPT = Optional

NS = Not Supplied

SECTION 1

DESCRIPTION

Figure 1-4. PS724-Series Oven Components Locations

2EMOVABLE

#ONVEYOR

!SSEMBLY

#ASTERS

4EMPERATURE

#ONTROLLER

3PEED

#ONTROL

(EAT#ONVEYOR

3WITCH

-AIN"LOWER

3WITCH

2EMOVABLE

%ND0LUG5PPER

2EMOVABLE

%ND0LUG,OWER

SECTION 1

DESCRIPTION

II. COMPONENT FUNCTION (Figure 1-4)

A. Conveyor Motor and Conveyor Belt

The conveyor belt is driven by a variable-speed electric

motor (Figure 1-5) operating through a gear reducer.

The motor speed is controlled by a digital control. The

stainless-steel wire belt can travel in either direction at

variable rates ranging from 30 seconds to 12 minutes; this

is the time that a product can take to pass through

the oven.

B. Blower Fan

The circulation air blower drive motors (2) are located in

the right side control box. The blowers force heated air

through the air fingers. The MAIN / BLOWER switch

must be set to “ON” or “I” for oven warmup and baking.

C. Cooling Fan — See Figure 1-5 and Figure 1-6

Cooling fans are located at the rear of each (left and

right) control box. Cooling air is drawn into each control

box and blown across the control components and

circulating blower bearings and exits the oven front and

rear louvers.

IMPORTANT

THE CONTROL BOX DOORS MUST BE

CLOSED WHILE THE OVEN IS HOT OR

HEATING IN ORDER TO KEEP THE

COMPONENTS AND BEARINGS COOL.

D. Air Fingers - See Figure 1-7

An Air Finger Assembly is made up of three parts:

1. Outer Plate - The Outer Plate is the removable covering

with tapered holes, which direct the air stream onto the

product being baked.

2. Inner Plate -The perforated Inner Plate is vital in forming

the unique air jets. It must be assembled into the manifold

with its holes aligned with the holes of the outer plate.

3. Manifold - The Manifold is the assembly which slides

on tracks into the oven plenum.

Figure 1-5. Machinery Compartment

Components

Blower Assembly

Right Control Box

#OOLING&AN

"LOWER

-OTOR

Conveyor

Drive Motor

SECTION 1

DESCRIPTION

Figure 1-6. Cooling Fan

#OOLING

&AN'RILLE

#OOLING&AN'RILLE

0OWER#ABLE%NTRANCE

"LOWER-OTOR!CCESS

0OWER#ABLE%NTRANCE

"LOWER-OTOR!CCESS

#ONNECTION

"LOCK!CCESS

SECTION 1

DESCRIPTION

Figure 1-7. Air Finger.

Outer Plate

Inner Plate

Finger

Manifold

Assembly

Baffle

SECTION 2

INSTALLATION

WARNING

Do not obstruct the flow of combustion and ventilation air to and from your oven. There must be no

obstructions around or underneath the oven. Constructional changes to the area where the oven is

installed shall not affect the air supply to the oven.

CAUTION

For additional installation information, contact your local Authorized Service Agent.

NOTE

There must be adequate clearance between the oven and combustible construction. Clearance

must also be provided for servicing and for proper operation.

NOTE

An electrical wiring diagram for the oven is located inside the machinery compartment.

WARNING

The oven must be installed on an even (level) non-flammable flooring and any adjacent walls must

be non-flammable. Recommended minimum clearances are specified in the Description section of

this Manual.

NOTE - AUSTRALIA INSTALLATION

In Australia, the oven installation must conform with any requirements of the appropriate statutory authority.

NOTE - CANADA INSTALLATION

In Canada, the oven installation must conform with local codes. Installed ovens must be electrically

grounded in accordance with local codes, or in the absence of local codes, with the Canadian Electrical Code

CSA C22.2.

NOTE

In the USA, the oven installation must conform with local codes. Installed ovens must be electrically

grounded in accordance with local codes, or in the absence of local codes,

with the National Electrical Code (NEC), or ANSI/NFPA70.

NOTE

All aspects of the oven installation, including placement, utility connections, and ventilation requirements,

must conform with any applicable local, national, or international codes. These codes supersede the

requirements and guidelines provided in this manual.

NOTE - CE OVEN INSTALLATION

Four casters are provided to allow the oven to be more easily moved to the installation location. These casters

are intended to simplify pre-installation movement only, and are NOT suitable for use as part of a CE oven

installation. During the installation procedure, the casters MUST be removed, so that the oven can be

supported by the supplied 152mm adjustable legs.

SECTION 2

INSTALLATION

SECTION 2

INSTALLATION

NOTE: The oven, when installed, must be electrically

grounded in accordance with local codes, or in the ab-

sence of local codes, with the National Electrical Code

(NEC), or ANSI/NFPA70.

NOTE

There must be adequate clearance between

the oven and any adjacent combustible con-

struction. Clearance must also be provided

for servicing and for operation.

CAUTION

It is recommended that the oven be placed under

a ventilation hood for adequate air supply and

ventilation.

CAUTION

Do not obstruct the flow of ventilation air to and

from your oven. Do not obstruct the fan holes in

the rear of the unit.

I. UNLOADING

Your Middleby Marshall PS724-Series Oven is shipped

partially assembled. It will arrive in a carton on a crate.

Carton size for a PS724-Series Oven is:

56.3″ (1422 mm) Long ×

41″ (1041 mm) Wide ×

40″ (1013 mm) High

The crate and carton must be examined before signing the

Bill of Lading. Report any visible damage to the transport

company, and check for the proper number of crates. If

apparent damage is found, make arrangements to file a

claim against the carrier. Surface Interstate Commerce

Regulations (U.S.A.) require that the claim must be

initiated by the consignee within 10 days from the date that

the shipment is received.

SECTION 2

INSTALLATION

Figure 2-1. PS724-Series Electric Oven Installation Kit

03/6%.).34!,,!4)/.

2%15)2%$+)43!.$%15)0-%.4

490% 03 33 03 33

3INGLE /VEN $OUBLE/VEN 4RIPLE /VEN&RXQWHU

).34!,,!4)/.

)NSTALLATION )NSTALLATION )NSTALLATION )NSTALLATION

+IT0. +IT0. +IT0. +IT0.

   

 #%  #%  #%

3INGLE /VEN  

$OUBLE/VEN  1$

4RIPLE/VEN1$

Qty. Qty. Qty. Inc. with Inc. with

Single Double Triple domestic CE

Item Oven Oven Oven Part No. ovens? ovens? Description

1 1 1 1 61243 Yes Yes Base pad

2 2 2 2 59835 Yes Yes Top panel

3 4 4 -- 37900-0024 Yes Yes 15″ (381mm) leg extension,

for single and double ovens

4 2 2 2 22290-0009 Yes Yes Caster, with flat plate and brake

5 2 2 2 22290-0010 Yes Yes Caster, with flat plate (no brake)

NOTE: Domestic and standard export ovens include 2 braking casters (item 5) and 2 non-braking casters (Item 6).

CE-approved ovens include 4 non-braking casters (Item 6) SOLELY for the purpose of moving the oven to the installation

location. Casters are NOT suitable for use as part of CE oven installations. Refer to the notice on the preceding page.

6 4 4 4 22450-0028 No No Leg, adjustable, 6″ (152mm)

7 1 1 1 21392-0004 Yes Yes Eyebolt, 3/4″

8 A/R A/R A/R 220373 Yes Yes Hex bolt, 3/8″-16 x 1″

NOTE: CE-approved ovens include 32 hex bolts. Domestic and standard export ovens include 31 hex bolts and one eyebolt

(item 8) that acts as an anchor for the restraint cable (Item 12). CE ovens are mounted on legs (Item 7) and do not use a

restraint cable.

9 32 32 32 21416-0001 Yes Yes Flat washer, 3/8″

10 32 32 32 21422-0001 Yes Yes Lockwasher, 3/8″

11 1 1 1 22450-0228 Yes Yes Restraint cable assembly

12 1 1 1 61778 Yes Yes Owner's Operating and Installation

Manual

13 1 1 1 1002040 Yes Yes Authorized Service Agency Listing

14 1 1 -- 61226 Yes Yes Lower shelf

8, 9, 10

SECTION 2

INSTALLATION

Figure 2-5. MODEL PS724 SINGLE OVEN DIMENSIONS

SECTION 2

INSTALLATION

Figure 2-6. MODEL PS724 DOUBLE OVEN DIMENSIONS

SECTION 2

INSTALLATION

Figure 2-7. MODEL PS724 TRIPLE OVEN DIMENSIONS

SECTION 2

INSTALLATION

WARNING

DO NOT USE CONDUIT FOR

GROUND CONNECTION.

CAUTION

IT IS RECOMMENDED THAT THE OVEN

BE PLACED UNDER A VENTILATION

HOOD FOR ADEQUATE AIR SUPPLY

AND VENTILATION.

ELECTRIC SUPPLY TO BE

PROVIDED BY CUSTOMER

CIRCUIT BREAKER

A seperate circuit breaker with lockout/tagout electrical

shutoff is required for each, seperately wired oven.

See breaker sizing requirements below:

ELECTRICAL SPECIFICATIONS

NOTE: Please refer to page 2, Electrical Specifications

chart and your units data plate information, for more

detailed information.

DOMESTIC: 208V, 60 Hz, 14.4 kW, 50A Service

240V, 60 Hz, 14.4 kW, 50A Service

480V, 60 Hz, 14.4 kW, 25A Service

NOT

use conduit for ground.

EXPORT: CE MODEL

208V, 50/60 Hz, 14.4 kW, 50A Service

230-240V, 50/60Hz, 13.2/14.4 kW, 50A Service

380V, 50/60 Hz, 14.4 kW, 25A Service

NOT

use conduit for ground.

POWER RATING

14.4 kW Standard

17.4 kW Optional

UTILITY ROUGH-IN DIMENSIONS AND POSITIONING

FOR PS724-SERIES OVENS

SUPPLY WIRE

Supply wire size must be in accordance with the

National Electrical Code (current edition) and must be in

compliance with local codes.

SUGGESTED

If space permits, service should be located near the

control console end of the oven(s) to allow convenient

access to safety switches.

II. VENTILATION GUIDELINES

Use of a ventilation hood is not required for proper

operation, but installation must conform with all local

codes and regulations.

Local codes and conditions vary greatly from one area to

another and must be complied with. Following are the

suggested requirements for good ventilation. Please re-

member these are recommendations or guidelines, you

may have a special condition or problem that will require

the services of a ventilation engineer or specialist. Proper

ventilation is the oven owner’s responsibility. Improper

ventilation can inhibit oven performance.

Figure 2-9. Typical PS724-Series Oven(s)

Installation



MM



MM

3UGGESTEDDIMENSIONSARESHOWNUTILITYCODE

REQUIREMENTSSUPERSEDEANYFACTORSSHOWN

4O/VEN

Suggested dimensions are shown; utility code

requirements supersede any factors shown.

SECTION 2

INSTALLATION

III. ELECTRICAL CONNECTION INFORMATION

FOR PS724-SERIES OVENS.

WARNING

Authorized supplier personnel normally ac-

complish the connections for the ventilation

system, electric and gas supplies, as ar-

ranged by the customer. Following these

connections, the factory-authorized installer

can perform the initial startup of the oven.

Check the oven data plate (Figure 2-10) before making any

electric supply connections. Electric supply connections

must agree with data on the oven data plate.

NOTE: The electric supply installation must satisfy the

requirements of the appropriate statutory authority, such

as the National Electrical Code (NEC), ANSI/NFPA70,

(U.S.A.); the Canadian Electrical Code, CSA C22.2; the

Australian Code AG601; or other applicable regulations.

A fused disconnect switch or a main circuit breaker

(customer furnished) MUST be installed in the electric

supply line for each oven; it is recommended that this

switch/ circuit breaker have lockout/tagout capability. The

electric supply connection must meet all national and local

electrical code requirements. Copper is the recommended

material for the electrical supply conductors.

IV. ELECTRIC SUPPLY

Electrical connection is made through a cord and plug.

A cord, plug and strain relief is supplied for Domestic

oven models, only. International ovens must supply,

See Electrical Specifications chart on page 2.

The supply conductors must be of the size and

material (copper) recommended to provide the cur-

rent required; (refer to the data plate for the ampere

specifications). The electric current rating for each

conductor supplying a PS724-Series Oven is 1.5A.

Figure 2-10. Typical Electric Oven Data Plate

International CE Plate

Domestic Plate

Figure 2-11. Junction Connection Box

ELECTRICAL

INLET

SECTION 3

OPERATION

SECTION 3

OPERATION

I. CONTROL FUNCTIONS

WARNING

A possibility of injury from rotating parts and

electric shock exists in this oven.

Never disassemble or clean the oven with the

BLOWER switch or any other oven control turned

“ON” or “I”. Turn “OFF” or “O” and lockout or

tagout all electric power to the oven before

attempting to clean or service this oven.

Figure 3-1. PS724-Series Oven Control Functions

4EMPERATURE

#ONTROLLER

3PEED

#ONTROL

(EAT#ONVEYOR

3WITCH

-AIN"LOWER

3WITCH

SECTION 3

OPERATION

II. COMPONENT INFORMATION AND

LOCATION (Figures 3-1 and 3-2)

A. Door Safety Switch

The Door Safety Switch is located at the lower right side

of control panel opening. Opening the control panel door

permits this switch to open, disconnecting power to all

electrical controls, except for the blower motor inverters,

located in the left side control cabinet.

CAUTION

Do NOT touch the wires going to this safety switch.

Current is always present.

B. Blower Switch

The blower switch has two positions. The switch must

be “ON” or “I” for the main blowers to come on and permit

the oven to run. The fan circulates the air throughout the

oven and must stay on during baking and during the

cool down cycle above 200°F (93°C) to prevent blower

bearing damage. To protect the blower motor and

bearings a thermostatic override is built into the oven.

If the temperature inside the oven is over 180°F (82°C)

the main blower will continue to run after the blower

switch is turned to the “OFF” or “O” position.

C. Heat / Conveyor Switch

The “Heat/Conveyor Switch” allows the burner to activate.

Activation is determined by the settings on the Digital

Temperature Controller.

D. Temperature Controller

The temperature controller is a solid-state, PID type to

maintain the operator-set temperature. The temperature

controller continuously monitors the oven temperature and

turns on the modulating solid state relay controller. The

heat is proportioned as required to maintain a constant

oven temperature.

The temperature controller contains a low-limit switch

which allows the oven to cool down to 200°F (93°C) before

shutting off the blower. A high-limit indication (ALM 1) will

appear on the display if the oven reaches 650°F (343°C).

Figure 3-2. Interior View of Control Console

4EMPERATURE

#ONTROL

#ONVEYOR0OWER4RANSFORMER

#ONVEYOR3PEED

#ONTROL"OARD

#IRCUIT"REAKERS

"LOWER-AIN

3WITCH

(EAT#ONVEYOR

3WITCH

(I,O"LOWER

3PEED2ELAY

$ISC

4HERMOSTAT

(IGH,IMIT

2ESET

(IGH,IMIT

4HERMOSTAT

#ONVEYOR

'EARMOTOR

#OOLING&AN

Page is loading ...

Middleby Marshall PS724E User manual

Brand: Middleby Marshall

Model: PS724E

Category: Ovens

Type: User manual

This manual is also suitable for

Download PDF

report

Middleby Marshall PS724E User manual

This manual is also suitable for

Middleby Marshall PS724E User manual

Related papers

Other documents