Craftsman 113213090 Owner's manual

Brand: Craftsman

Model: 113213090

Category: Power tools

Type: Owner's manual

This manual is also suitable for

113.213090

Craftsman 113213090 is a 10-inch bench model drill press with a maximum developed 1/2 HP motor. It features 4 speeds, a sturdy base, and a precision chuck. This drill press is ideal for a variety of drilling applications, including woodworking, metalworking, and plastic. With its powerful motor and variable speed settings, the Craftsman 113213090 can handle a wide range of drilling tasks, from small precision holes to large holes in thick materials. The sturdy base and precision chuck ensure accurate and stable drilling, while the adjustable table allows for drilling at various angles.

f Save ThisManual "_

I For FutureReference

MODEL NO.

113.213090

DRILL PRESS WITH

MAXIMUM DEVELOPED

1/2 HP MOTOR

Serial

Number

Model and serial number

may be found at the rear of

the head.

You should record both

model and serial number in

a safe place for future use.

CAUTION:

READ ALL

iNSTRUCTIONS

CAREFULLY

BENCH

MOTORIZED

10-INCH

MODEL DRILL PRESS

• assembly

• operating

e repair parts

",... .j ../

Sold by SEARS, ROEBUCK AND CO., Chicago, IL 60684 U.S.A.

Part No. SP5t85 Printed in Taiwan

GENERAL SAFETY INSTRUCTIONS FOR POWER TOOLS

1, KNOW YOUR POWER TOOL

Read and understand the owner's manual and

labels affixed to the tool Learn its application and

limitations as well as the specific potential hazards

peculiar to this tool.

2. GROUND ALL TOOLS

This tool is equipped with an approved 3-conductor

cord and a 3-prong grounding type plug to fit the

proper grounding type receptacle. The green con-

ductor in the cord is the grounding w_re. Never

connect the green w_reto a live terminal.

3. KEEP GUARDS IN PLACE

In working order, and in proper adjustment and

alignment.

4. REMOVE ADJUSTING KEYS AND WRENCHES

Form a habit of checking to see that keys and

adjusting wrenches are removed from tool before

turning It on.

5. KEEP WORK AREA CLEAN

Cluttered areas and benches inviteaccidents. Floor

must not be slippery due to wax or sawdust.

Z87.1) at al! times. Everyday eyeglasses are not

safety glasses. They only have impact resistant

lenses Also. use face or dust mask if cutting oper-

atior is dusty, and ear protectors (plugs or muffs)

during extended oeriods of operation.

13. SECURE WORK

Use c_arnps or a vise [o hold work when practical.

It frees both hands to operate tool.

DON'T OVERREACH

Keep proper footing and balance at all times.

MAINTAIN TOOLS WITH CARE

Keep tools sharp and clean for best and safest

performance. Follow instructions for lubricating and

changing accessories.

16. DISCONNECT TOOLS

Before servicing; when changing accessories such

as blaoes bits, cutters, etc.

17. AVOID ACCIDENTAL STARTING

Make sure switch is in "OFF" position before olug-

glng _n

18. USE RECOMMENDED ACCESSORIES

15.

6, AVOID DANGEROUS ENVIRONMENT Consult the owner's manual for recommended ac-

Don't use power tools in damp or wet locations or cessor es Fo ow the

expose them to rain. Keep work area well lighted, the accessories. The instructions that accompany

use of improper accessories

Provide adequate surrounding work space.

7. KEEP CHILDREN AWAY

All visitors should be kep_ a safe distance from

work area

8. MAKE WORKSHOP CHILD-PROOF

With padlocks, master switches, by removing star-

ter keys. or storing tools where children can't get

them.

9. DON'T FORCE TOOL

It will do the job better and safer at the rate for

which it was designed.

10. USE RIGHT TOOL

Don't force tools or attachment to do a job it was

not designed for.

11. WEAR PROPER APPAREL

19.

20.

may cause hazard s,

NEVER STAND ON TOOL OR ITS STAND

Serious injury could occur if the tool is tipped or if

the cutting tool is accidentally contacted. Do not

store materials above or near the tool such that _t

is necessary to stand on the tool or _ts stand to

reach them

CHECK DAMAGED PARTS

Before further use of the tool. a guard or other part

that =sdamaged should be carefully checked to

ensure that it will operate properly and perform its

=ntended functJon Check for alignment of moving

parts, b_nding or moving parts, breakage of parts.

mounting, and any other conditions that may affect

its operation. A guard or other part that is damaged

Do not wear loose cothing goves necktes, or should be proper_y repaired or replaced.

jewelry (rings wristwatchesito get c_Lught n mov- 21. DIRECTION OF FEED

ing p_trts. NONSLIP f0otwear S re ;ornmended Feed work nto a b ade or cutter aga nst the d rec-

Wear protective ha r cover ng to conla n ong hair. t on of rotation of the bade or cutter on y

Roll t(_ngsleeves above the elbow. 22 NEVER LEAVETOOL RUNNING UNATTENDED

12. USESAFETYGOGGLES(HEADPR :)TECTION) Turn power off Dont eave too unt t comes to a

Wear safety goggles (must _om'rp wth ANSi compete stop.

additional

safety instructions for drilm presses

WARNING: FOR YOUR OWN SAFETY, DO NOT

ATTEMPT TO OPERATE YOUR DRILL PRESS

UNTIL iT iS COMPLETELY ASSEMBLED AND IN-

STALLED ACCORDING TO THE iNSTRUCTIONS...

AND UNTIL YOU HAVE READ AND UNDERSTAND

THE FOLLOWING:

1. General Safety instructions for Power Tools. 2

2. Getting to Know Your Drill Press ........ 17

3. Basic Drill Press Operation ............. 22

4. Adjustments .......................... 24

5. Maintenance .......................... 25

6. Stability of Drill Press

If there is any tendency of the drill press to tilt or

move during any use, bolt it to the floor or a flat

piece of 1/2" exterior plywood large enough to

stabilize the drill press. Bolt the plywood to the

underside of the Base. so it extends at least to

both sides. Make sure the plywood won't trip the

operator, Do not use pressed wood panels--

they can break unexpectedly.

If the workpiece is too large to easily support with

one hand, provide an auxiliary support.

7. Location

Use the drill press in a well lit area and on a level

surface clean and smooth enough to reduce the

risk of trips, slips, or falls. Use it where neither the

operator nor a casual observer is forced to stand

in line with a potential kickback.

8. Kickback

A kickback occurs when the workpiece is suddenly

thrown in the OPPOSITE direction to the DIREC-

TION OF FEED: THIS CAN CAUSE SERIOUS IN-

JURY. Kickbacks are most commonly caused by

use of accessories NOT recommended for this tool.

9. Protection: Eyes, Hands, Face, Ears and Body

WARNING: TO AVOID BEING PULLED INTO

THE SPINNING TOOL --

1. Do NOT wear:

-- gloves

-- necktie

-- loose clothing

-- jewelry

2. Do tie back long hair

a. Ifany part ofyour drillpress ismissing, malfunc-

tioning, has been damaged or broken.., such

as the motor switch, or other operating control,

a safety device or the power cord . . . cease

operating immediately until the particular part

is properly repaired or replaced.

b. Never place your fingers in a position where

they could contact the drilI or other cutting tool

if the workpiece should unexpectedly shift or

your hand should slip.

c. To avoid injury from parts thrown by the spring,

follow instructionsexactly as given and shown

in adjusting spring tension of quill.

d: To prevent the workpiece from being .E_

torn from your hands, spinning of the _"

toot. shattering the tool or being thrown, "_

always properly support your work so t,_

it won't shift or bind on the tool:

-- Always position BACKUP MATERIAL (use :_

beneath the workpiece) to contact the left -D

side of the column. "._

-- Whenever possible, position the WORK-

PIECE to contact the left side of the col-

umn-if it is too short or the table is tilted,

clamp solidly to the table. Use table slots

or clamping ledge around the outside edge

of the table.

-- When using a drill press VICE, always fas-

ten it to a table.

-- Never do any work "FREEHAND" (hand-

holding workpiece rather than supporting it

on the table), except when polishing.

-- Securely lock Head and Support to Column,

and table to support before operating drill

press.

-- Never move the Head or Table while the

tool is running.

-- Before starting the operation, jog the motor

switch to make sure the drill or other cutting

tool does not wobble or cause vibration.

- If a workpiece overhangs the table such

that it will fall or tip if not held, clamp it to

the table or provide auxiliary support.

- Use fixtures for unusual operations to

adequately hold, guide and position work-

piece.

-- Use the SPINDLE SPEED recommended

for the specific operation and workpiece

material--check the inside of the Belt

Guard for drilling information; for acces-

sories, refer to the instructions provided

with the accesso[ies.

f. Never climb on the drill press Table, it

could break or pull the entire drill press

down on you.

g. Turn the motor Switch Qff and put away

the Switch Key when leaving the drill

press.

h. To avoid injury from thrown work or tool

contact, do NOT perform layout, as-

sembly, or setup work on the table while

the cutting tooI is rotating,

10. Use only accessories designed for this

drill press to avoid serious injury from

thrown broken parts or work pieces.

a. Holesaws must NEVER be operated on

this drill press at a speed greater than

400 RPM

b. DrumsandersmustNI _ER be operated on

the drill press at a sp_ d greater than 1800

RPM.

o. Do not insta I or use an_ rill that exceeds 7" in

length or extends 6' b#lc the chuck jaws. They

Cad suddenly bend out_ rd or break.

d Do not use wire whee s, )uter bits, shaper cut-

ters circle (fly) cutters € rotary planers on this

drill press.

11. Note and Follow the Safety Warnings and In-

structions that Appear on the Panel on the

Right Side of the Head:

o o

I DANGER J FOR YOUR OWN SAFETY:

Know This Tool! Read and Understand Owner's Manual before Using th=s

Machine, Use Recommended Drill S_eed- See Chart inside Pulley Cover,

m Always wear safety goggles that comply with ANSI Z87.1

m Donotweargloves.necktieorlooseclothing Tieback SP=NO_E

long hair. _N

m Securelyclampworktotableifitistooshort tocontact

the column when in operatmg position.

• Securely lock head and support to Column. and table _" ('U_

to support, before operating drill press,

O a Use only recommended accessories. E82443 O

12. This Drill Press has 4 speeds as listed below:

48ORPM

930 RPM

1750 RPM

3000 RPM

See inside of guard for specific placement of belt

on pulleys.

13 Think Safety, Safety is a combination of operator

common sense and alertness at all times when the

drill press is being used.

WARNING: DO NOT ALLOW FAMILIARITY (GAINED

FROM FREQUENT USE OF YOUR DRILL PRESS)

TO BECOME COMMONPLACE. ALWAYS RE-

MEMBER THAT A CARELESS FRACTION OF A

SECOND iS SUFFICIENT TO iNFLICT SEVERE

INJURY,

The operation of any power toot can result in foreign

objects being thrown into the eyes, which can result in

severe eye damage. Always wear safety goggles com-

ply with ANSl Z87.1 (shown on Package) before com-

rnenc_ng 0ower tool operation. Safety Goggles are

available at Sears retail or catalog stores.

WEAR YOUR

glossary of terms

1. Workpiece

The item on which the cutting operations is being

performed.

2. Drill

The cutting toot used in the dril_ press to make holes

in a workpiece.

3. Backup Material

A piece of wood placed between the workpiece and

table .... it prevents wood in the workpiece from

splintering when the drill passes through the back-

side of the workpiece .... also prevents drilling into

the table top.

4. Revolution Per Minute (R.P.M.)

The number of turns completed by a spinning object _=

in one minufe,

5. Spindle Speed

The RPM of the spindle. _"

table of contents

Page

General Safety Instructions for Power Tools ...... 2

Additional Safety Instructions for Drill Presses .... 3

Glossary of Terms ....................... 5

Table of Contents .......................... 5

Motor Specifications and Electrical

Requirements .......................... 6

Unpacking and Checking Contents ............. 7

Table of Loose Parts ........................ 8

Location and Function of Controls ............. 9

Assembly ................................ 10

Assembly of Base/Column ............... 10

Installation of TabletSupport .............. 10

Installing the Head ..................... 13

Installing Feed Handles ................. 14

Installing the Chuck ..................... 14

Installing Belt Guard Knob ............... 15

Tensioning Belt ........................ 15

Adjusting the Table Square to Head ....... I6

Bevel Scale ........................... 16

Getting to Know You_ Drdl Press

On-Off Switch

Remownq The Chuck

Dnlhng Io Depth ......

Page

.. . 19

Depth Sca_e ........... 21

Bas=c Drill Press Operation .. . 22

Installing Drills ........... 22 "_

Pos*honmg Table and VVorko_ece ... 23€_

T_thng Table ..... 23 "_

Hole hocatlon 24

Feeding 24 "_

Adlus[rnenls ............ 24

Qudl Relurn Sprtng. . 24

Maintenance ............ 25

Lubncat_on ...................... 25

Recommended Accessories 25

Trouble Shoot_ng ................ 26

Repair Parts 27

ifi _ m

motor spec Tca ons and electrica requ

i_i !i_i_i_i_

° t i¸

reme s

MOTOR SPECiFICATiONS

TNs dril! press is designed to use a 1725 RPM motor

only. Do not use any motor that runs faster than 1725

RPM It is wired for operation on 110-120 volts. 60 Hz.

alternating current,

WARNING: TO AVOID INJURY FROM UNEX-

PECTED STARTUP, DO NOT USE BLOWER OR

WASHING MACHINE MOTORS OR ANY MOTOR

WITH AN AUTOMATIC RESET OVERLOAD PRO-

TECTOR.

CONNECTING TO POWER

SOURCE OUTLET

This machine must begrounded while _nuse to protect

the operator from electric shock.

Plug power cord Into a 110-!20V properly grounded

type outlet protectea by a 15-amo dual element time

delay or Circuit breaker.

NOT ALL OUTLETS ARE PROPERLY GROUNDED.

IF YOU ARE NOT SURE THAT YOUR OUTLET, AS

PICTURED BELOW. iS PROPERLY GROUNDED,

HAVE IT CHECKED BY A QUALIFIED ELECTRiCiAN.

WARNING: TO AVOID ELECTRIC SHOCK. DO NOT

TOUCH THE METAL PRONGS ON THE PLUG,

WHEN INSTALLING OR REMOVING THE PLUG TO

OR FROM THE OUTLET.

WARNING: FAILURETO PROPERLY GROUNDTHIS

POWER TOOL CAN CAUSE ELECTRICUTION OR

SERIOUSSHOCK, PARTICULARLY WHEN USED IN

DAMP LOCATIONS. OR NEAR METAL PLUMBING.

IF SHOCKED, YOUR REACTION COULD CAUSE

YOUR HANDS TO HIT THE CUTTING TOOL

IF POWER CORD IS WORN OR CUT, OR DAMAGED

IN ANY WAY, HAVE IT REPLACED IMMEDIATELY

TO AVOID SHOCK OR FIRE HAZARD.

This power tool is equipped with a 3-conductor

and grouna_ng type plug, approved by Underwriters'

Laooratories and the Canadian Standards Association:

The grouna conductor has a green jacket and is at_

tached to the tool housing at one end and to the grour]d

prong in the attachment plug at the other end.

This plug requires a mat ng 3-conductor grounded type

outlet as shown.

If the outlet you are planning to use for this power tool

s of the two prong type, DO NOT REMOVE OR ALTER

THE GROUNDING PRONG IN ANY MANNER. Use

an adapter as shown and always connect the grounding

tug to known ground.

It is recommended that you have a qualified electrician

replace the TWO prong outlet with a properly grounded

THREE orong outlet.

An adaoter as shown below isavailable for connecting

plugs to 2-pror_g receptacles.

WARNING: THE GREEN GROUNDING LUG EX-

TENDING FROM THE ADAPTER MUST BE CON-

NECTED TO A PERMANENT GROUND SUCH AS

TO A PROPERLY GROUNDED OUTLET BOX.

GROUNDING LUG

SCREW \

ADAPTER

3-PRONG

PLUG

GROUNDING

PRONG

has a plug that looks

NOTE: The adapter illustrated is for use only if you

alreaoy nave a properly grounded 2-prong receptacle,

Adapter is not allowed inCanada by the Canadian Elec-

trical Code.

The use of any extension cord will cause some loss of

0ower. To Keep this to a minimum and to prevent over-

neatmcj and motor bum-out, use the table below to

determine the minimum wire size (A W.G) extension

cord Use only 3 wire extension cords which have 3-

prong grounding type plugs and 3-pote receptacles

which accept the tools ptug.

Extension Cord Length Wire Size A.W.G.

0-25Feet 16

26-50Feet !4

51-100 Feet 12

unpacking and checking contents

WARNING: TO AVOID iNJURY FROM UNEX-

PECTED STARTING OR ELECTRICAL SHOCK, DO

NOT PLUG THE POWER CORD iNTO A SOURCE

OF POWER. THIS CORD MUST REMAIN UNPLUG-

GED WHENEVER YOU ARE WORKING ON THE

DRILL PRESS.

Model 113.213090 Drill Press is shipped compiete n

one box.

1. Unpacking and Checking Contents

a. Separate ali "loose parts" from packaging mate-

rials and check each item with "Table of Loose

Parts" to make sure ali items are accounted for

before discarding any packing material

WARNING: IF ANY PARTS ARE MISSING, DO NOT

ATTEMPT TO ASSEMBLE DRILL PRESS, PLUG IN

THE POWER CORD, OR TURN THE SWITCH ON

UNTIL THE MISSING PARTS ARE OBTAINED AND

ARE INSTALLED CORRECTLY.

2 Remove the protective oil that is apoliec to the

table and column. Use any ordinary hoLJsehold type

grease and spot remover.

WARNING: TO AVOID FIRE OR TOXIC REAC-

TION, NEVER USE GASOLINE, NAPTHA OR

SIMILAR HIGHLY VOLATILE SOLVENTS.

3 Apply a coat of paste wax to the tab!e and co!umn

to prevent rust. Wipe all parts thoroughly with a clean

dry cloth.

TABLE OF LOOSE pARTS

Item Description Qty.

A " " r, ,_, Asrlr_.... I

Tae e Su_..pL t ............. _ "_

_:: Column SL_pport As,q"_ .................. _ _ "_

C Owners MamJa ................... .E o

D Box of Loose Parts ................. ' o c

E Base ......... _ = L_• • .............. t*_

F Head A..... _',_ ................ 1 _,.,c

i o

G Bag of Loose Parts ...........

List of Loose Parts in Box 507884

item Description Qty.

Chuck Key . ...................... 1

Chuck .............................. 1

List of Loose Parts in Bag 507885

item Description Qty.

C Feed Handle ........................ 3 C

D Wrench Hex "L" 3mm ................ 1

E Wrench Hex "L" 4mm ................ 1

*F Knob ............................. 1

*G Screw Pan Hd, M5 x 0.8-12 .......... 1

H Table Crank ........................ 1

I Support LOCKHandle ................. 1

*J Switch Key ........................ 1

*K Screw Hex Hd M8 x 1.25-20 .......... 4

These Parts Shown =ull Size

E J

G....G ]'llltlrl,l,l'l'lt!'l'l'g (_ H

location and function of controls

1, BELT TENSION LOCK HANDLES... Tightening

handles locks motor bracket support and BELT

TENSION HANDLE to maintain correct belt dis-

tance and tension,

2. FEED HANDLE... For moving the chuck up or

down, One or two of the handles may be removed

if necessary whenever the workpiece is of such

unusual shape that it interferes with the handles,

3. TABLE CRANK . . . Turn clockwise to elevate

table. Support lock must be released before operat-

ing crank,

4. CHUCK KEY... Used to tighten drill in the chuck

and also to loosen the chuck for drill removal.

5. CHUCK... Holds drill bit or other recomrpended

accessory to perform desired operations.

6. DEPTH SCALE... Allows operator to adjust drill

press to drill to a desired depth.

7. DRILL "ON-OFF" SWITCH . . . Turns drift press

on and off . . , also used to lock drill press in off _

position, ,_ o

8. DEPTH SCALE LOCK Locks the depth scale

at selected position. _ o

.-J to

9. SPRING CAP Provides means tc ; ,_just quill "

spring tension, u,.

10. HEAD LOCKS... Locks the head to the columr

ALWAYS have them locked in place while operaz-

ing the drill press.

. • , ÷_

11. BEVEL SCALE Shows degree tab_ s ,_ted

for bevel operations.

12. SUPPORT LOCK HANDLE... Tightening locks

table support to column, Always" have it Iocke(_ tn

place while operating the Drill Press.

13. TABLE BEVEL LOCK... Locks the table in any

position from 0'_'-45 °.

.... TOOLS NEEDED ..............

SCREWDRIVER

SQUARE _J"

8-INCH ADJUSTABLE

WRENCH

FRAMING SQUARE MUST BE TRUE,

-Check its accuracy as il;ustrated below,

DRAW LIGHT STRAIGHT EDGE OF

LINE ON BOARD BOARD 3/4" THICK--

THIS EDGE MUST BE

PERFECTLY STRAIGHT

JflllJltli!li JIl tlltllltlll

8mm DIA. x 20turn LONG BOLT

ASSEMBLY OF BASE/COLUMN

1 Position base on floor. Remove protect_vecoverlng

and discard

2, Remove protective sleeve from column tube and

discard. Place column assembly on base, and align

holes in column support with holes in base.

3. Locate four (4) 8ram Dia. x20ram long bolts among

oose parts bag,

4, Install a bolt _neach hole through column support

and base and tighten with adjustable wrench.

ALONG THE EDGE ,_

SHOULD BE NO GAP OR OVERLAP WHEN

SQUARE IF FLIPPED OVER IN DOTTED POSITION

RACK

COLUMN

ASSEMBLY

1, L_sen set screw n Column collar with 3ram HEX

wrenchandremove co ar and rack from co umn COLUMN

COLLAR

SPECIAL NOTE: Make sure the elevation worm gear

shaft is extending through the opening in the table sup-

port as far as possible -- See Illustration.

2. With long smooth end of rack pointing upward, slide

rack down through large round opening in table

support. Engage rack in gear mechanism found

inside opening of table support.

RACK

TABLE

SUPPORT

TABLE

3. While hotding rack and table support in an engaged

position slide both down over column. Slide rack

down column until rack is positioned against lower

column support.

TABLE

RACK

COLt.

GEAR

MECHANISM

ELEVATION

WORM GEAR

SHAFT

ELEVATION

WORM GEAR

SHAFT

LOWER

COLUMN

SUPPORT

4. Replace column collar and position it bevel side

down over rack. Tighten set screw in collar with

3ram HEX "E' wrench. To let the rack slide when

the table is swung to the left or right around the

column, the collar must s_t loosely over rack aria

should not be angled on the column- Only tighten

set screw enough to keep collar _nulace, otherwise

the collar may De broken due to excess pressure

CAUTION: To avoid co lumn tube or collar dam-

age, do not over tighten set screw.

COLUMN

COLLAR

RACK

5. Locate support lock handle in loose 3arts bag.

6. Install support lock from left side into table support

and tighten by hand.

TABLE

SUPPORT_

SUPPORT

LOCK HANDLE

7. Locate table crank in loose parts bag.

8. Install table crank assemb y and tighten set screw

with a 3turn HEX "E' wrench.

TABLE

SUPPORT

TABLE

CRANK

INSTALLING THE HEAD

CAUTIONi The head assembly weighs about 45

pounds. Carefully li_ head.

1. Remove protective covering from head.

2. Carefully lift head above column tube and slide it

down on the column as far as it will go. Align head

with table and base.

HEAD

COLUMN

Using a 4mm Hex 'L" wrench tighten the head lock

set screws on the right side of the head

HEAD LOCK

SET SCREWS

..J

HEAD

!NSTALL{NG FEED HANDLES

! Lecate th_-ee_3i feed handl_-s amor; 9 io0se pa,*ls.

2 S(_w _ie feed ha:nd_es tight!y i_to 1he threaded

_ht hub

HUB

FEED

HANDLE

INSTALUNG THE CHUCK

_ocale the chuck among loose parts

CIear: out the TAPERED HOLE in the chuck: clean

the spindle nose with a clean cloth. Make sure

the_e are no foreign partic}es sticking to the sur-

faces The slightest piece of dirt on the spindle

nose or _n the chuck wi_ prevent the chuck from

seating proper!y THis w;_ cause the drill to

X,vobbte '

NOTE: _f TAPERED HOLE in the chuck iS ex-

tremeIy dirty, use a c_eamng so_vent on the clean

do_h

CHUCK

•:_ Push the cr]_Jc:Kup on lhe spindle nose ;Asfa as

,t w_t go

4 ]urn cm_ck sleeve clockwise and open jaws _n

chuck Cornpietely

5 L_gntb! lap the nose of the chuck w_th a _ece of

woeo _o _nsure r_roper seating of the d]uck on the

spindle.

SPINDLE

J NOSE

CHUCK

14.

BELT GUARD KNOB

5rr_m DiA x !2ram LONG

SCREW

INSTALUNG BELT GUARD KNOB

1 To attach belt guard k:ob !ocate knob ar'd 5ram

Oa × 12ram ong par] hd screw _ loose parts

bag _nstalJ sc_ew n hoe ocated _n guarc and ab

taCh knob t_rnmg ;_;1_ l/ghl

WARNING: TO AVOID POSSIBLE INJURY KEEP

GUARD 1N PLACE AND _N PROPER WORKtNG

ORDER WHILE OPERATING.

PAN NO. SCREW

BELT GUARD KNOB

BEt.T

TENSION

LOCK

HANDLE

TENSIONING BELT

NOTE: T,__ Dr_ll P,ess s :m_pped w_ff: th(? bet _r_St,:_Jied

but _tshoud be pro;beriy t_.'m,oq_-,'dbefor÷, Js(,_

! i.lfl (juard f[orn qghl s,;xe apt! e:-_v(' Op!}nei on

hinge

2 Looser Be!t Te,%on Lock Hand!es !ocaled on

BOTH SIDES of 0_1t P_es;head P}il the motor

toward flont of @! pzess to r{:,_eve tens;o _on t}elt

BELT

TENSION

HANDLE

3 Choose speed for drii!ing operation, and move belt

to correct position for desired speed

NOTE: Refer to chart _nside belt guard for Recom-

mended Drilfing Speeds

4 _._ovethe_d.1orrearwarotoaop_yte_ls_ontothe

5.TightenBeetTensionLOCkHandles

NOTE:Be_,tSHOULDdeflectapprox_matewI/2'_ by

thuntb pressure at mid-point of be_t between pulleys.

6 C_ose De_1[guard.

7 _ be_t s_[_£ ,*rhinedrfihng, readjust belt tension.

BELT

LOCK HANDLE

ADJUSTING THE TABLE SQUARE TO

HEAD

NOTE: The comb_nahon square rT1USt[3_ "_"Uf_ See

Unpack_n_ and Checking Contents section to_

mettled

• b_sert orec_s_on round steel rod approxlnqatel',i 3

_ong rote chuck and tighten

2 With table raised to working height aria locked on

CO_LJrT'_n.p_ace combmatlon square flat on table De-

side rod

PRECISION

ROD

3 _fan adjustment _snecessary _oesen tl_e set screw

under bevetIock w_th 3ram "L wrench then loosen

the table bevel IoCk bolt with an adj LJstan_ewrench

(Th_s adjustmen,, _slocated unaer the tablel

4 Ahgn the table square to the rod by relating table

unt_] the square arid rod are n I_ne

5 Ret_ghten table beve lock

6 Retighten set screw

SCREW

TABLE

BEVEL

LOCK

TABLE

BEVEL SCALE

NOTE: The beve! scale t_as been included to Drowae

a qu_ck method for bevehng the table to approximate

angIes, tt precise accuracy ts necessary, a square, or

o_hef prec|s}on measuring tool should be used to pose-

hen the table

1 To use {he bevel scale do the loltow ng

a. Loosen set screw and table beve! lock,see steo

3 above_

b Move table so desired angle on beve sea e s

straigh_ across from zero line on table

c Ret_g_en table beve_ tock ana se_ screw

SCALE

POINTER

TABLE

getting to

knOW

your driSl

FEED HANDLE

press

BELT GUARD

O o_

.F5

DEPTH SCALE LOCK

DEPTH

SCALE

DEPTH

iNDiCATOR

FEED SPRING

ADJ USTME NT 18

TABLE

FEED

SPRING

BELT TENSION LOCK

HANDLE

COLUMN COLLAR

rABLE SUPPORT

TABLE CRANK

COLUMN

RACK

COLUMN SUPPORT

HEAD LOCK SET

SCREWS

SPRING CAP

SUPPORT LOCK

HANDLE

ON-OFF SWITCH

TABLE BEVEL LOCK

BEVEL SCALE

CHUCK

KEY

BASE

{_ ,,,/ SPLINES

(GROOVES)

fJ_L,_-"'-_ SP,NDLE

_ (TEETH)

CHUCK

QUILL AND SPINDLE ASSEMBLY

iNSiDE OF DRILL PRESS

This Drill Press has 4 speeds as listed below:

480 RPM

930RPM

1750 RPM

3000 RPM

See inside of belt guard for soecific placement of belts

on pulleys.

SPINDLE[ SPEEDS IN R.P.M.

480

1750

930

3OOO

! BELT GUARD... Covers pulleys and belt dunng

operation of drill press

2. BELT TENSION LOCK HANDLE... Tightening

handle locks motor bracket support to maintain c0r-

rect belt dtstance and tension

3. COLUMN COLLAR... Holds tne rack lo the co_-

umn Rack remains movable in collar to permit

table support movement.

4 TABLE SUPPORT... Rides on column to support

table

5. TABLE CRANK . _ . Turn ClOCKWiSe [O elevate

table. Support lock handle must be released before

operating crank

6. RACK... Combines with gear mechanism to pro-

vide easy elevatton of table by hand operated table

Crank

7 COLUMN SUPPORT... Supports column and

provides mounting holes for column to base

8 BASE... Supports Drill Press. F:or addihonat sta-

bility: holes are provided in base to bolt Drill Press

to bench {See "Additional Safety Instruchons for

Drill Presses.'h

9. CHUCK ,., Holds anll bit or other recommended

accessory 1o perform desired operations.

10. CHUCK KEY... It is a self-electing chuck key

which wtll "'pop" out of the chuck when you let go

of it. This action is designed to help prevent throw-

mg of the chuck key from the chuck wnen power

_s turned "ON, Do not use any other key as a

substitute, oraer a new one d damaged or lost

11 TABLE BEVEL LOCK ... Locks the table m any

position from 0 -45.

12. BEVEL SCALE... Shows degree table Js hlted

for bevel operations. Scale _s moun_eo on table

suoport. It is to be used for qu_ck reference where

accuracy is not critical

13 SUPPORT LOCK . . . T ghtentng locks tabe sup-

port to column. Always have _tlocked _nplace whde

operating the Unll Press

14 SPRING CAP ... Provides means to adjust qudt

spring tension

15 HEAD LOCK SET SCREWS... Locks the head

to the column ALWAYS have them locked tn place

wh_le operating tne drill press,

16 ON-OFF SWITCH ... Has locking feature THIS

FEATURE IS INTENDED TO PREVENT UNAU-

THORIZED AND POSSIBLE HAZARDOUS USE

BY CHILDREN AND OTHERS

_7 COLUMN.. Coqnec[s head, table, and base on

a one-piece tube for easy alignment and move-

ment

18 TABLE . . Prowaes working surface to support

workplece

DEPTH SCALE iNDICATOR... Indicates drilling

oepth selected on deoth scale.

DEPTH SCALE _ _ . Shows depth of hole being

drdled in mcnes and milhmeters

21, DEPTH SCALE LOCK... Locks the depth scale

to selected ae ptn

22 FEED HANDLE . . . For mov=ng the chuck up or

aown One or two of the handles may be removed

if necessary whenever the workpiece Js of such

unusual shade that _tinterferes with the handles

23 BELT TENSION . . Refer to sechon Tensioning

Bett "

24 DRILLING SPEED... Can be changed by placing

the belt n any of the STEPS [grooves! _nthe pul-

leys See Spindle Speed chart _nside belt guard,

DRILL "ON-OFF" SWITCH . .. Has Iocmng feature

THIS FEATURE tS XITENDED TO HELP PREVENT

UNAUTHORIZED AND POSSIBLE HAZARDOUS USE

BY CHILDREN AND OTHERS

Insert KEY into swftch

NOTE: Key _s made of yellow plastic.

€.J

L,U . =::::

To turn drill ON . . .

Insert finger under switch lever and pull.

To turn drill OFF, . . Push lever in,

In an emergency;, . . the drill bit BINDS., , STALLS

. . . STOPS . . . or tends to tear the workpiece loose

• .. you can QUICKLY turn the drill OFF by hitting the

switch with the palm of your hand.

To lock switch in OFF position , , . hold switch IN with

one hand ... REMOVE key with other hand,

WARNING: FOR YOUR OWN SAFETY, ALWAYS

LOCK THE SWITCH "OFF" WHEN DRILL PRESS IS

NOT IN USE . .. REMOVE KEY AND KEEP IT IN A

SAFE PLACE ... ALSO... iN THE EVENT OF A

POWER FAILURE (ALL OF YOUR LIGHTS GO OUT)

OR BLOWN FUSE OR TRIPPED CIRCUIT

BREAKER, TURN SWITCH OFF . . . LOCK IT AND

REMOVE THE KEY. THSS WILL PREVENT THE

DRILL PRESS FROM STARTING UP AGAIN WHEN

THE POWER COMES BACK ON.

REMOVING THE CHUCK

1 Open jaws of chuck as wide as they w_lt go by

turning chuck sleeve,

2. Carefully tap chuck w_th mallet n one hand while

holding other hand under chuck to catch _twhen

_t falls. It may be necessary to lap tlqe crluck at

several different spots around the top of the chuck.

SLEEVE_

CHUCK_

CHU(

BODY

DRILLING TO A SPECIFIC DEPTH

To drill a BLIND hole (not all the way through) to a

given depth, proceed as follows.

1. Mark the depth of the hoe on the s de of the work-

piece. •

2. Loosen the depth scale lock.

3. With the switch OFF bring the dri!l down until the

TIP or lids of the dril are even with the Mark

4. Turn the depth scale counterclockwise until it stops

moving.

5. Tighten the depth scale lock.

6. The drill will now be stopped at this depth until the

deoth scale is readjusted,

DEPTH SCALE"

LOCK

DEPTH

SCALE

Page is loading ...

Craftsman 113213090 Owner's manual

Brand: Craftsman

Model: 113213090

Category: Power tools

Type: Owner's manual

This manual is also suitable for

113.213090

Download PDF

report

Craftsman 113213090 Owner's manual

This manual is also suitable for

Craftsman 113213090 Owner's manual

Related papers

Other documents