CDA SC210SS Specification

Category
Ovens
Type
Specification

This manual is also suitable for

FAN
OVENS
Instruction for the use - Installation advice
KEEP IN A SAFE PLACE
Before operating this oven,
please read these instructions carefully
2
Dear Customer,
Thank you for having purchased and given your preference to our
product.
The safety precautions and recommendations within this booklet
are for your own safety and that of others. They will also provide
a means by which to make full use of the features offered by your
appliance.
Please preserve this booklet carefully. It may be useful in future,
either to yourself or to others in the event that doubts should arise
relating to its operation.
This appliance must be used only for the task it has explicitly
been designed for, that is for cooking foodstuffs. Any other form
of usage is to be considered as inappropriate and therefore dan-
gerous.
The manufacturer declines all responsibility in the event of dam-
age caused by improper, incorrect or illogical use of the appliance.
DECLARATION OF
CE
CONFORMITY
This oven has been designed to be used only for cooking. Any other use (such as
heating a room) is improper and dangerous.
This oven has been designed, constructed, and marketed in compliance with:
- safety requirements of EEC Directive “Low voltage” 2006/95
- safety requirements of EEC Directive “EMC” 89/336;
- requirements of EEC Directive 93/68.
IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN
ACCORDANCE WITH EC DIRECTIVE 2002/96/EC.
At the end of its working life, the product must not be disposed of as
urban waste. It must be taken to a special local authority differentiated
waste collection centre or to a dealer providing this service.
Disposing of a household appliance separately avoids possible negative
consequences for the environment and health deriving from inappropriate
disposal and enables the constituent materials to be recovered to obtain
significant savings in energy and resources. As a reminder of the need
to dispose of household appliances separately, the product is marked
with a crossed-out wheeled dustbin.
3
IMPORTANT PRECAUTIONS AND RECOMMENDATIONS
After having unpacked the appliance, check to ensure that it is not damaged.
If you have any doubts, do not use it and contact the store from where you
purchased it.
– Packing materials (i.e. plastic bags, polystyrene foam, nails, packing straps, etc.)
should not be left around within easy reach of children, as these may cause serious
injuries.
– Do not attempt to modify the technical characteristics of the appliance as it may
become dangerous to use.
Do not carry out cleaning or maintenance operations on the appliance without having
previously disconnected it from the electric power supply.
If you should decide not to use this appliance any longer (or decide to substitute an
older model), before disposing of it, it is recommended that it be made inoperative in
an appropriate manner in accordance to health and environmental protection regula-
tions, ensuring in particular that all potentially hazardous parts be made harmless,
especially in relation to children who could play with old appliances.
IMPORTANT PRECAUTIONS AND RECOMMENDATIONS FOR USE OF ELECTRICAL
APPLIANCES
Use of any electrical appliance implies the necessity to follow a series of fundamental
rules. In particular:
Never touch the appliance with wet hands or feet;
do not operate the appliance barefooted;
do not allow children or disabled people to use the appliance without your supervision.
The manufacturer cannot be held responsible for any damages caused by improper,
incorrect or unreasonable use of the appliance.
USING THE OVEN FOR THE FIRST TIME
You are advised to carry out the following operations:
Assemble the interior of the oven as described under the heading “Cleaning and main-
tenance”
Switch the empty oven ON at maximum temperature for about two hours to eliminate
traces of grease and smell from the components.
Let the oven cool down, switch off the electrical supply, then clean the inside of the
oven with a cloth soaked in water and neutral detergent and dry thoroughly.
4
Control panel
11
Fig. 1.1
A
U
T
O
40
50
60
100
30
0
20
10
90
80
70
110
120
2
3
6-71(A or B)
4
A
U
T
O
P
2
3
51(A or B)
4
2
3
8-9-101(A or B)
4
2
3
11-121(A or B)
4
TYPES OF THERMOSTAT
Depending on the models the thermostat
could be of type A (50 to 225°C) or type
B (50 to 250°C)
A
Fig. 1.2
Fig. 1.3
Fig. 1.4
B
CONTROL PANEL
1. Oven thermostat knob (type A or B)
2. Function selector knob
3. Power on indicator lamp
4. Oven temperature indicator lamp
5. Electronic programmer
6. Electronic clock/end cooking timer
5
55
50
45
40
35
30
25
20
15
10
5
0
2
3
6-7 1(A or B)
4
A
U
T
O
P
2
3
5 1(A or B)
4
2
3
1(A or B)
4
2
3
1(A or B)
4
8-9-10
11-12
A
U
T
O
Fig. 1.5
Fig. 1.6
Fig. 1.7
Fig. 1.8
7. Electronic clock
8. Clock programmer (start-end)
9. Electric clock with alarm
10. Electric clock
11. Timer (120’ cut-off)
12. 60’ alarm
6
GENERAL FEATURES
The heating and cooking in electrical hot
air ovens take place by forced convec-
tion.
The two elements which make this pro-
cess take place are:
- Grill element 2000 W
- Circular element 2200 W
NOTE:
Upon first use, it is advisable to operate
the oven at the maximum temperature
(thermostat knob on the maximum posi-
tion) for 60 minutes in the position
to eliminate possible traces of grease on
the heating elements.
Repeat the operation for another 15
minutes with the grill element on as
explained in the chapters GRILLING
and USE OF THE GRILL.
WARNING:
The door is hot, use the handle.
During use the appliance becomes hot.
Care should be taken to avoid touching
heating elements inside the oven.
OPERATING PRINCIPLES
Heating and cooking in the fan oven are
obtained in the following ways:
a. by forced convection
A fan sucks in the air contained in the
oven, which circulates it through the
circular heating element and then
forced back into the oven by the fan.
Before the hot air is sucked back
again by the fan to repeat the
described cycle, it envelops the food
in the oven, provoking a complete and
rapid cooking. It is possible to cook
several dishes simultaneously.
b. by radiation
The heat is radiated by the infra red
grill element.
c. by ventilation
The food is defrosted by using the
fan only function without heat.
Fig. 2.1A
How to use the oven
22
GREASE FILTER (some models only)
A special screen is provided at the
back of the oven to catch grease par-
ticles, mainly when meat is being
roasted (see page 23).
When baking pastry etc. this filter
should be removed.
Always clean the filter after cooking as
any solid residues on it might adverse-
ly affect the oven performance.
7
THERMOSTAT KNOB (fig. 2.1A - 2.1B)
To turn on the heating elements of the
oven, set function selector knob to the
required position and the thermostat
knob to the desired temperature.
To set the temperature, turn the thermo-
stat control knob indicator mark to the
required temperature.
The elements will turn on or off automat-
ically which is determined by the thermo-
stat.
The operation of the heating elements is
signalled by a light placed on the control
panel.
0
Fig. 2.2
Attention: the oven door becomes
very hot during operation.
Keep children away.
Fig. 2.1B
FUNCTION SELECTOR KNOB (fig. 2.2)
Rotate the knob clockwise to set the
oven to one of the following functions:
OVEN LIGHT
By turning the function selector knob to
this setting, the oven light will illuminate
in the oven cavity (15W).
The oven light will operate on all select-
ed functions.
DEFROSTING FROZEN FOODS
Only the oven fan is on.
To be used with the thermostat knob in
the off “” position because the other
positions have no effect.
The defrosting is done by simple venti-
lation without heat.
Recommended for:
To rapidly defrost frozen foods; 1 kilo-
gram requires about one hour.
The defrosting times vary according to
the quantity and type of foods to be
defrosted.
8
REGENERATION
Set the switch to position and the
thermostat knob to position 150° C.
Bread becomes fragrant again if wet with
a few drops of water and put into the
oven for about 10 minutes.
COOKING ADVICE
STERILIZATION
Sterilization of foods to be conserved, in
full and hermetically sealed jars, is done
in the following way:
a. Set the switch to position
b. Set the thermostat knob to position
175 °C and preheat the oven.
c. Fill the dripping pan with hot water.
d. Set the jars onto the dripping pan
making sure they do not touch each
other and the door and set the ther-
mostat knob to position 125 °C.
When sterilization has begun, that is,
when the contents of the jars start to
bubble, turn off the oven and let cool.
GRILLING
The infra-red heating element is switched
on. The heat is diffused by radiation.
Use with the oven door closed and the
thermostat knob must be regulated
between 50°C and 200°C max.
For correct use see chapter “USE OF THE
GRILL”.
Recommended for:
Intense grilling action for cooking with the
broiler; browning, crisping, “au gratin”,
toasting, etc.
It is recommended that you do not
grill for longer than 30 minutes at any
one time.
Attention: the oven door becomes
very hot during operation.
Keep children away.
HOT AIR COOKING
The circular element and the fan are on.
The heat is diffused by forced convec-
tion and the temperature must be regu-
lated between 50°C and the maximum
position with the thermostat knob.
It is not necessary to preheat the oven.
Recommended for:
For foods that must be well done on the
outside and tender or rare on the inside,
i. e. lasagna, lamb, roast beef, whole
fish, etc.
COOKING DIFFERENT DISHES AT
THE SAME TIME
With the function selector in position
, the ventilated oven allows you to cook
different types of food at the same time.
Fish, cakes and meat can be cooked
together without the smells and flavours
mixing.
The only precautions required are the
following:
The cooking temperatures must be as
close as possible with a maximum dif-
ference of 20° - 25°C between the dif-
ferent foods.
Different dishes must be placed in the
oven at different times according to
the cooking time required for each
one. This type of cooking obviously
provides a considerable saving on
time and energy.
9
ROASTING
To obtain classical roasting, it is neces-
sary to remember:
– that it is advisable to maintain a tem-
perature between 180 and 200 °C.
– that the cooking time depends on the
quantity and the type of foods.
USE OF THE GRILL
Set the switch to position and the
thermostat knob between 50°C and
200°C max.
Leave to warm up for approximately 5
minutes with the door closed.
Introduce the food to be cooked, posi-
tioning the rack as close to the grill as
possible.
The dripping pan should be placed
under the rack to catch the cooking
juices and fats.
Grilling with the oven door closed.
Grilling with the oven door closed and
do not for longer than 30 minutes at
any one time.
Attention: the oven door becomes
very hot during operation.
Keep children away.
10
Electronic programmer
33
A
U
T
O
P
Fig. 3.1
Fig. 3.2
Description of the buttons:
Timer
Cooking time
End of cooking time
Manual position and cancellation of
the inserted cooking program
or To increase the numbers on
the digital display
or To decrease the numbers on
the digital display.
The electronic programmer is a device
which groups together the following func-
tions:
24 hours clock with illuminated display
Timer (up to 23 hours and 59 minutes)
Program for automatic oven cooking
– Program for semi-automatic oven
cooking.
Description of the illuminated
symbols:
AUTO - flashing - Programmer in auto-
matic position but not pro-
grammed
AUTO - illuminated - Programmer in
automatic position with program
inserted.
Automatic cooking taking place
Timer in operation
and AUTO - flashing - Program
error.
(The time of day lies between the
calculated cooking start and end
time).
Note:
Select a function by the respective but-
ton and, in 5 seconds, set the required
time with the ( ) / ( ) buttons
(“one-hand” operation).
After a power cut the display resets to
zero and cancels the set programs.
11
Fig. 3.3
A
U
T
O
Fig. 3.4
ELECTRONIC CLOCK (fig. 3.2)
The programmer is equipped with an
electronic clock with illuminated num-
bers which indicates hours and minutes.
Upon immediate connection of the oven
or after a power cut, three zeros will
flash on the programmer display.
To set the correct time of day it is nec-
essary to push the button and then
the ( ) or ( ) button until you
have set the correct time (fig. 3.2).
In another way push simultaneously the
two buttons and at the same time
push the ( ) or ( ) button.
Note: If the clock is reset it deletes any
previously set programs
ELECTRONIC TIMER
The timer program consists only of a
buzzer which may be set for a maximum
period of 23 hours and 59 minutes.
If the AUTO symbol is flashing push the
button.
To set the time, push the button and
the ( ) or ( ) until you obtain
the desired time in the panel (fig. 3.4).
Having finished the setting, the clock
hour will appear on the panel and the
symbol will be illuminated.
The countdown will start immediately and
may be seen at any moment on the panel
by simply pressing the button .
At the end of the time, the symbol
will disappear and the buzzer will sound
and continue for approximatley 7 min-
utes or until a button is pressed (not the
( ) / ( ) buttons). After a short
time the display will revert back to the
time of day.
SETTING THE FREQUENCY OF THE
AUDIBLE SIGNAL
The buzzer has 3 different tones and can
be changed by pressing the ( ) but-
ton, but only when the time of day is dis-
played
NORMAL COOKING WITHOUT THE
USE OF THE PROGRAMMER
To manually use the oven, without the
aid of the programmer, it is necessary to
cancel the flashing AUTO by pushing the
button (AUTO will be switched off
and the symbol will illuminate - Fig.
3.3).
Attention: If the AUTO is illuminated
(which means a cooking program has
already been inserted), by pushing the
button you cancel the program and
return to manual operation.
If the oven is switch on, you must
switch off manually.
12
A
U
T
O
P
A
U
T
O
P
Fig. 3.6Fig. 3.5
AUTOMATIC OVEN COOKING
To cook food automatically in the oven,
it is necessary to:
1. Set the length of the cooking period
2. Set the end of the cooking time
3. Set the temperature and the oven
cooking program.
These operations are done in the
following way:
1. Set the length of the cooking period
by pushing the button and the
( ) button to increase, or ( )
to decrease if you have passed the
desired time (fig. 3.5). The AUTO and
the symbol will illuminate.
2. Set the end of the cooking time by
pressing the button (the cooking
time already added to the clock time
will appear), and the ( ) button
(fig. 2.6); if you pass the desired time
you may get back by pushing the
( ) button.
After this setting, the symbol will
disappear. If after this setting, the
AUTO flashes on the display and a
buzzer sounds, it means there was
an error in the programming, that is
that the cooking cycle has been
superimposed on the clock. In this
case, modify the end of cooking time
or the cooking period itself by follow-
ing again the above mentioned
instructions.
3. Set the temperature and the cooking
program by using the switch and ther-
mostat knobs of the oven (see specific
chapters).
Now the oven is programmed and every-
thing will work automatically, that is the
oven will turn on at the right moment to
end the cooking at the established hour.
During cooking, the symbol remains
illuminated.
By pushing the button you can see
the time that remains until the end of
cooking.
The cooking program may be can-
celled at any time by pushing .
At the end of the cooking time the oven
will turn off automatically, the symbol
will turn off, AUTO will flash and a buz-
zer will be sound, which can be turned
off by pushing any of the buttons except
the ( ) / ( ) buttons.
Turn the switch and thermostat knobs to
zero and put the programmer onto “man-
ual” by pressing the button.
Attention: After a power cut the clock
resets to zero and cancels the set pro-
grams.
After a power cut, three zeros will flash
on the display.
13
A
U
T
O
P
A
U
T
O
P
Fig. 3.7
Fig. 3.8
SEMI - AUTOMATIC COOKING
This is used to automatically switch off
the oven after the desired cooking peri-
od has elapsed.
Set the length of the cooking period by
pushing the button and the ( )
button to increase, or ( ) to
decrease if you have passed the desired
time (Fig. 3.7).
AUTO and the symbol will be illumi-
nated.
Then set the temperature and the cook-
ing program using the function selector
switch and thermostat knobs (see spe-
cific chapters).
The oven is switched on and it will be
switched of automatically at the end of
the desired time.
During cooking, the symbol remains
illuminated and by pressing the button
you can see the remaining cooking
time..
The cooking program can be can-
celled at any time by pushing the
button.
At the end of the cooking period, the oven
and the symbol will disappear, AUTO
will flash and a buzzer will sound and can
be stopped by pushing any of the buttons
except the ( ) / ( ) buttons
.
Turn the function selector switch and
thermostat knobs to zero and put the
programmer onto “manual” by pressing
the button.
14
The electronic programmer is a device
with the following functions:
24 hours clock with illuminated
display
Timing of oven cooking with automatic
switch-off (max. 99 minutes).
ELECTRONIC CLOCK
Upon immediate connection of the oven
or after a mains failure, three zeros will
flash on the programmer panel.
To set the clock it is necessary to push
the button and then, within 7 seconds,
the or button until you have set the
correct time.
The clock will show zero after a mains
failure.
Attention: When the programmer
display shows three flashing zeros the
oven cannot be switched on.
The oven can be switched on when the
symbol is shown in the display.
A
U
T
O
ELECTRONIC ALARM
The programmer can be used as an
alarm only for a maximum period of 99
minutes.
To set the alarm, push the or
button until you obtain the desired time
in the display. Once the time has
elasped, an intermittent buzzer, lasting 7
minutes, will start; this can be stopped
by pressing the button.
Attention: If the bottom oven is
switched on when the buzzer starts, it
will be automatically switched off. For it
to operate furtherly you have to stop the
buzzer by pressing the button.
SETTING THE FREQUENCY OF THE
ALARM SOUND
The selection from 3 possibilities of
sound can be made by pressing the
button.
Fig. 4.1
COOKING WITH AUTOMATIC
SWITCH-OFF
The aim of this function is to
automatically stop the cooking after a pre
programmed time, for a maximum period
of 99 minutes.
To set the cooking time, push the or
button until you obtain the desired
time in the display. The symbol AUTO
will be shown in the display. Then you
adjust the oven thermostat knob
according to the required temperature.
The oven will immediately start to
operate and will work for the pre
programmed time. The display shows the
count down. Clock time can be displayed
by pressing the button. Once the time
has elasped, the oven will switch off
automatically, the symbol AUTO will go
off and an intermittent buzzer, lasting 7
minutes, will start; this can be stopped by
pressing the button.
Important: Before the buzzer is stopped
switch off the oven manually.
To cancel the cooking program at any
time press the and buttons
together and release the button first.
Electronic clock/end cooking timer
44
15
Fig. 5.1
ELECTRONIC CLOCK (fig. 5.1)
The electronic alarm is a device which
groups the functions of 24 hours clock
with illuminated display and 99 minutes
alarm.
Upon immediate connection of the oven
or after a blackout, three zeros will flash
on the programmer panel.
To set the hour it is necessary to push
the button and then, within 7 sec-
onds, the or button until you have
set the exact hour.
An energy black-out makes the clock
go to zero.
ELECTRONIC ALARM
The alarm program consists only of a
buzzer which may be set for a maximum
period of 99 minutes.
To set the time, push the or until
you obtain the desired time in the panel.
Having finished the setting, the sym-
bol will be lighted and the countdown will
start immediately. At the end of the time,
the symbol will be switched off and
an intermittent buzzer, during 7 minutes,
will go off; this can be stopped by press-
ing the buttons.
To stop the alarm countdown in any
moment press the and buttons
together and release the button first.
SETTING THE FREQUENCY OF THE ALARM
SOUND
The selection from 3 possibilities of
sound can be made by pressing the
button.
Electronic clock
55
16
Clock programmer
66
COOKING WITH AUTOMATIC SWITCH-OFF
– Turn on the oven by setting the switch
knob on the desired program and the
thermostat knob onto the desired tem-
perature (see specific chapters).
– Set the cooking time by rotating knob
“A” anticlockwise until desired time in
window “B” coincides with the indica-
tor (Fig. 6.2).
The oven will immediately start to oper-
ate and will work for the pre pro-
grammed time. Once the time has
elasped, the oven will switch off auto-
matically and an intermittent buzzer will
start; this can be stopped by rotating
knob “A” until the symbol in window
“B” coincides with the indicator (Fig.
6.3).
Turn the switch and thermostat knobs to
“off” position.
The clock programmer is a device which
groups together the following functions:
Electric clock
Timing of oven cooking with automatic
switch-off (max. 180 minutes).
End cooking buzzer
SETTING THE TIME
To adjust, simply press the knob “A” (fig.
6.1) and rotate anticlockwise to the cor-
rect time.
MANUAL COOKING (without programmer)
To use the oven without the program-
mer, i.e. only with the function selector/
thermostat, the programmer function
must be cancelled by rotating knob “A”
anticlockwise until the symbol in win-
dow “B” coincides with the indicator (Fig.
6.1).
Fig. 6.1
Fig. 6.2
Fig. 6.3
A
A
A
B
B
B
17
ELECTRIC CLOCK WITH ALARM
(Fig. 7.1)
To adjust the clock, press knob “A” and
turn clockwise until it shows the correct
time.
Caution: the knob “A” will become loose
if turned anticlockwise.
Fig. 7.1
A
C
MINUTE COUNTER
The minute counter function consists
simply of an acoustic signal which
comes on once the set time has
elapsed.
To set the minute counter, rotate the
small knob (A) clockwise or anticlock-
wise (without pressing it) until the hand
(C) coincides with the required time
(max 55 minutes) (Fig. 7.1).
Countdown will begin immediately and
the hand (C) will begin to turn anticlock-
wise, always showing the remaining
time.
Once the set time has elapsed the bell
will ring until the hand (C) is positioned
to the symbol by rotating the knob
(A) anticlockwise.
Electric clock with alarm - Electric clock
77
ELECTRIC CLOCK (Fig. 7.2)
To adjust the clock, press knob “A” and
turn clockwise until it shows the correct
time.
Caution: the knob “A” will become loose
if turned anticlockwise.
Fig. 7.2
A
18
88
Timer - 60’ Alarm - 120’ Alarm
60’ ALARM (fig. 8.2)
The minute counter is a timed acoustic
warning device which can be set for a
maximum of 60 minutes.
The knob must be rotated clockwise as
far as the 60 minute position and then
set to the required time by rotating it
anticlockwise.
120’ ALARM (fig. 8.3)
The minute counter is a timed acoustic
warning device which can be set for a
maximum of 120 minutes.
The knob must be rotated clockwise as
far as the 120 minute position and then
set to the required time by rotating it
anticlockwise.
110
100
90
80
70
60
50
40
30
20
10
0
TIMER - 120’ CUT-OFF (fig. 8.1)
The function of the timer runs the oven
for a preset time.
1) Starting up.
After setting the function selector and
thermostat to the required mode and
temperature, rotate the timer knob
clockwise until you reach the required
cooking time (max 120 minutes).
Once this time has elapsed, the timer
will return to the 0 position and the
oven will automatically switch off.
2) Manual position.
If the cooking time is longer than two
hours or if you wish to use the oven
manually, switching it off as required,
the knob must be turned to position
.
40
50
60
100
30
0
20
10
90
80
70
110
120
Fig. 8.3
55
50
45
40
35
30
25
20
15
10
5
0
Fig. 9.2
Fig. 9.1
Fig. 8.2
Fig. 8.1
19
INSIDE OF OVEN
The oven must be always cleaned after
every use, using suitable products and
keeping in mind that its operation for 30
minutes on the highest temperature
eliminates most grime reducing it to
ashes.
GENERAL ADVICE
Important:
Before any operation of cleaning and
maintenance disconnect the appli-
ance from the electrical supply.
It is advisable to clean when the
appliance is cold and especially for
cleaning the enamelled parts.
Avoid leaving alcaline or acidic sub-
stances (lemon juice, vinegar, etc.) on
the surfaces.
Avoid using cleaning products with a
chlorine or acidic base.
The oven must always be cleaned after
every use, using suitable products and
keeping in mind that its operation for 30
minutes on the highest temperature
eliminates most grime reducing it to
ashes.
Cleaning and maintenance
99
STAINLESS STEEL AND ALUMINIUM
PARTS AND SILK-SCREEN PRINTED
SURFACES
Clean using an appropriate product.
Always dry thoroughly.
IMPORTANT: these parts must be
cleaned very carefully to avoid scratching
and abrasion. You are advised to use a
soft cloth and neutral soap.
ENAMELLED PARTS
All the enamelled parts must be cleaned
with a sponge and soapy water only or
other non-abrasive products.
Dry preferably with a chamois leather.
Do not use a steam cleaner because
the moisture can get into the
appliance thus make it unsafe.
STAINLESS STEEL SURFACES WITH
ANTI-FINGERPRINT TREATMENT
CAUTION:
The stainless steel surfaces used in
some ovens are protected with a Special
Lacquer to reduce finger-print marks.
To avoid damaging this lacquer, do not
clean the stainless steel with abrasive
cleaners or abrasive cloths or scouring
pads.
ONLY SOAP/WARM WATER MUST BE
USED TO CLEAN THE STAINLESS
STEEL SURFACES.
Do not store flammable material in
the oven.
20
Fig. 9.3
Fig. 9.2
A
Models with wire racks
Assemble the wire racks to the oven
walls using the 2 screws (Fig. 9.2).
In the models with catalytic panels
interpose the catalytic panels “A” with
the arrow up (Fig. 9.2).
Slide in, on the guides, the shelf and
the tray (fig. 9.3).
The shelf must be fitted so that the
safety catch, which stops it sliding out,
faces the inside of the oven.
To dismantle, operate in reverse order.
Fig. 9.1
OVEN FITTING OUT
Models with embossed cavity
The oven shelves are provided with a
security block to prevent accidental
extraction.
They must be inserted operating as per
figure 9.1.
To pull them out operate in the inverse
order.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32

CDA SC210SS Specification

Category
Ovens
Type
Specification
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI